Skip to the content
2 layers84 × 59.5 mmHackpad V2, the printed circuit board in 3D

This is my very cool hackpad, with a oled screen, a rotary encoder with a switch and 6 switches.

Size
84 × 59.5 mm
Copper layers
2
Thickness
1.6 mm
Parts
19
Nets
20
Pads
71
Tracks, vias
128, 0
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
1 Jul 2026
Updated
15 Jul 2026

Overview

Hackpad V2 is an open-source printed circuit board by Random1011010, from the Random1011010/My-Very-Cool-HackPad repository on GitHub, published under the MIT licence. It is a 2-layer board of 84 × 59.5 mm with 19 parts on 20 nets, routed with 128 tracks and 0 vias.

Its parts include 7 switches, 6 diodes, 1 IC and 1 connector. It belongs with the lEDs and displays boards of this library.

README

README.md

My Very Cool HackPad

A 6-key macropad with a rotary encoder (push-button) and a 128x32 OLED display, built around the Seeed Studio XIAO RP2040. The OLED runs an idle-animated "Luna" sprite that cycles through sit, walk, run, sleep, and work.

Screenshot 2026-07-14 at 11 34 16 PM

About me

I'm a Grade 10 (going into Grade 11) student, I am interested in aerospace, but I wanted to get real hands-on experience with hardware and PCB design before jumping into anything bigger. This was my first full custom PCB build, so a lot of this project was just learning by doing.

Inspiration & Challenges

I wanted something I'd actually use, not just a demo board but rather, media controls, screen brightness, and a few shortcuts I use constantly (Spotlight, screenshot, undo/redo). The OLED also mattered to me too, I didn't want it just showing static text, so it runs a small animated character instead.

Most of the challenges were on the PCB and case side, since this was my first time doing either seriously. In KiCad, I had to fix a missing net label on one of the matrix columns, and ran into alignment issues while placing components that took a while to track down. Getting the rotary encoder's footprint right was its own thing.

The case went through a full rebuild. I first modeled it with not a clue how to I would get the keys to line up with the PCB, then rebuilt it in Fusion 360, sketch by sketch, to match Hack Club's submission format, while keeping the board dimensions (84x59.5mm), switch spacing, and heatset insert placement consistent with the original.

On the firmware side, I wrote the QMK code for the matrix, the encoder (volume normally, brightness when you hold the encoder's button), and the OLED animation, I adapted an open-source Luna sprite animation to loop continuously instead of reacting to typing, since I wanted it to feel more like a little idle character than a status display. (Hopefully it works)

Features

  • 6-key matrix (2 rows x 3 columns)
  • Rotary encoder with push-button:
    • Rotate: volume up/down (default)
    • Hold + rotate: screen brightness up/down
    • Short tap: play/pause
  • 128x32 I2C OLED with an idle-animated Luna sprite
  • QMK firmware, fully open source

Bill of Materials (BOM)

PartQtyUnit CostTotalNotes
Seeed Studio XIAO RP20401$5.00$5.00Main MCU
Cherry MX-style switches6$0.35$2.10
Keycaps6$0.30$1.80
Rotary encoder (EC11) with push-button1$0.90$0.90
128x32 I2C OLED display (SSD1306)1$5.90$5.90
Custom PCB1~$5.00$5.002-layer, JLCPCB/similar, price for small qty
3D printed case1~$3.00$3.00Filament cost estimate
M3 heatset inserts6$0.10$0.60
Diodes6$0.05$0.301N4148, one per switch
Total~$24.60

Pinout

FunctionPin
Matrix rowsGP26, GP27
Matrix colsGP29, GP0, GP3
Encoder A/BGP2, GP1
Encoder switchGP28
OLED SDAGP6
OLED SCLGP7

Photos

Exploded View Screenshot 2026-07-15 at 12 25 32 AM

Schematic:

Screenshot 2026-07-14 at 11 25 23 PM

PCB:

Screenshot 2026-07-14 at 11 26 05 PM

Case:

image

Firmware Written in QMK. Full source is in the firmware/ folder — see firmware/myverycoolpad/readme.md for build/flash instructions.

Status Parts haven't arrived yet, so the physical build and OLED orientation are untested. Firmware compiles cleanly with qmk compile -kb myverycoolpad -km default.

Parts

19
QtyValueFootprintReferences
61N4148Diode_THT:D_DO-35_SOD27_P7.62mm_HorizontalD1, D2, D3, D4, D5, D6
6SW_PushButton_Switch_Keyboard:SW_Cherry_MX_1.00u_PCBSW1, SW2, SW3, SW4, SW5, SW6
1Conn_01x04Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ1
1MOUDLE-SEEEDUINO-XIAOfootprints:XIAO-Generic-Hybrid-14P-2.54-21X17.8MMU1
1RotaryEncoder_SwitchRotary_Encoder:RotaryEncoder_Alps_EC11E-Switch_Vertical_H20mmSW7

The 15 most common of 19 parts.

Similar boards

  • 2 layers43.9 × 27.7 mmTcd1304-4v, the printed circuit board in 3D

    Tcd1304-4v

    OpnTec/open-spectrometer-hardware

    Open source VIS spectrometer

    19 parts1.5k
  • 2 layers50 × 60 mmDebate Device, the printed circuit board in 3D

    Debate Device

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    19 parts915
  • 2 layers102.9 × 96.7 mmISA adapter, the printed circuit board in 3D

    ISA adapter

    polpo/picogus

    Emulation of ISA sound cards and CD-ROM on Raspberry Pi Pico (GUS, SB/Adlib, MPU-401, Tandy, CMS, Panasonic CD-ROM) with USB mouse/joystick support

    19 parts805
  • 2 layers60 × 39 mmPs2usb, the printed circuit board in 3D

    Ps2usb

    rasteri/HIDman

    Adapting USB devices to work on old computers

    19 parts432
  • 2 layers70.1 × 43.2 mmIaq device, the printed circuit board in 3D

    Iaq device

    nkitanov/iaq_board

    IAQ Board is a DIY (Do-It-Yourself) device for measuring internal air quality

    19 parts396
  • 2 layers80 × 80 mmGB BRK CPU G1, the printed circuit board in 3D

    GB BRK CPU G1

    Gekkio/gb-hardware

    Game Boy -related custom hardware by gekkio

    19 parts379CC-BY-4.0
  • 2 layers25.4 × 25.4 mmIna169, the printed circuit board in 3D

    Ina169

    Ardumower/ardumower

    Develop an open source robotic lawn mower (HW+SW reference platform)

    19 parts282
  • 2 layers58.4 × 28.6 mmNew rele, the printed circuit board in 3D

    New rele

    zmaker/arduino_cookbook

    gli sketch del nuovo progetto Arduino Cookbook e dei video di YouTube

    19 parts269

Questions

How big is the Hackpad V2 PCB?

It measures 84 × 59.5 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Hackpad V2 use?

19 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Hackpad V2 KiCad files?

From the Random1011010/My-Very-Cool-HackPad repository on GitHub, at the commit this page was made from: the board is PCB Files/Hackpad V2.kicad_pcb and its schematic PCB Files/Hackpad V2.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Hackpad V2 design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).