
Rpi pico debugger shoe
ShawnHymel/rpi-pico-debugger-shoe
Stackable debugger board for the Raspberry Pi Pico. Solder long headers to this debugger board in order to connect the Pico to it.

High-efficiency 5V wide-input DC-DC power module for UAV avionics — KiCad, LTspice, PCB design
PwrBrk5V is an open-source printed circuit board by raju-gudala, from the raju-gudala/5v-Power-Module-UAV-avionics repository on GitHub, published under the MIT licence. It is a 2-layer board of 27.8 × 39.1 mm with 42 parts on 27 nets, routed with 249 tracks and 21 vias.
It is built around the LT8645SHV-2#PBF, 150060VS75000 and SMCJ64A-Q, with the XAL7070-332MEC among its other parts. Its parts include 14 capacitors, 12 resistors, 4 connectors, 2 ICs and 2 diodes. It belongs with the power boards of this library.
High-efficiency, wide-input 5V DC-DC power module designed for UAV avionics, supporting 3S–12S LiPo battery input using the LT8645SHV-2 synchronous buck converter.
Flight-critical avionics — flight controllers, GPS, telemetry modules, and onboard sensors — need clean, stable power regardless of battery state or LiPo cell count. This module was designed to deliver a regulated 5V rail across a wide input range, with protection and monitoring features built in to keep avionics powered reliably through the full flight envelope.
| Parameter | Value |
|---|---|
| Input voltage range | 3S–12S LiPo (~11.1V–50.4V) |
| Output voltage | 5V regulated |
| Converter IC | LT8645SHV-2 (synchronous buck) |
| Protection | Reverse-polarity, UVLO, soft-start |
| Monitoring | Power-good signal |
| Target loads | Flight controller, GPS, telemetry, onboard sensors |
├── schematics/ # KiCad schematic files
├── pcb/ # KiCad PCB layout files
├── simulation/ # LTspice simulation files
├── gerbers/ # Fabrication-ready Gerber files
└── docs/ # Datasheets, design notes, test results(Adjust the folder structure above to match what you actually push.)
Designed as part of UAV avionics hardware development at TiHAN-IIT Hyderabad.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 0.47uF, 100V, X7R | Capacitor_SMD:C_0805_2012Metric | C2, C4 |
| 2 | 10E | Resistor_SMD:R_0603_1608Metric | R9, R10 |
| 2 | 1uF, 16V, X7R | Capacitor_SMD:C_0603_1608Metric | C6, C9 |
| 2 | 4.7uF, 100V, X7R | Capacitor_SMD:C_1210_3225Metric | C1, C3 |
| 2 | 47uF, 16V, X7R, 1210 | Capacitor_SMD:C_1210_3225Metric | C10, C11 |
| 2 | NetTie_2 | NetTie:NetTie-2_SMD_Pad0.5mm | NT1, NT2 |
| 1 | 100k, 1% | Resistor_SMD:R_0805_2012Metric | R6 |
| 1 | 100k, 1% | Resistor_SMD:R_0603_1608Metric | R4 |
| 1 | 100nF, 16V, X7R | Resistor_SMD:R_0603_1608Metric | C13 |
| 1 | 100nF, 16V, X7R | Capacitor_SMD:C_0603_1608Metric | C15 |
| 1 | 100nF, 25V, X7R | Capacitor_SMD:C_0603_1608Metric | C7 |
| 1 | 10nF, 25V, X7R | Capacitor_SMD:C_0603_1608Metric | C5 |
| 1 | 120k, 1% | Resistor_SMD:R_0603_1608Metric | R3 |
| 1 | 150060VS75000 | PWR_brick:LEDC1608X70N | LED1 |
| 1 | 1M, 1% | Resistor_SMD:R_0603_1608Metric | R2 |
| 1 | 1k | Resistor_SMD:R_0603_1608Metric | R12 |
| 1 | 1nF, 100V, X7R | Capacitor_SMD:C_0603_1608Metric | C14 |
| 1 | 22k, 1% | Resistor_SMD:R_0603_1608Metric | R5 |
| 1 | 4.7pF, 50V, C0G | Capacitor_SMD:C_0603_1608Metric | C8 |
| 1 | 47E | Resistor_SMD:R_0603_1608Metric | R11 |
| 1 | 5.6k, 1% | Resistor_SMD:R_0603_1608Metric | R7 |
| 1 | 74279226101 | PWR_brick:WE-MPSB_181252 | L1 |
| 1 | 88.7k / 91k, 1% | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | BATT+ | PWR_brick:pad 7mmx7mm | J1 |
| 1 | BATT- | PWR_brick:pad 7mmx7mm | J2 |
| 1 | GND | PWR_brick:pad 7mmx7mm | J4 |
| 1 | INA240A2DR | PWR_brick:SOIC127P600X175-8N | IC2 |
| 1 | LOGO | LOGO | G*** |
| 1 | LT8645SHV-2#PBF | PWR_brick:LT8645SHV2PBF | IC1 |
| 1 | MSRPM3920R-0L50-D2P0 | PWR_brick:MSRPM3920R0L50D2P0 | R8 |
| 1 | PDB+ | PWR_brick:pad 7mmx7mm | J3 |
| 1 | Power | PWR_brick:SM06B-GHS-TB | POWER1 |
| 1 | SMCJ64A-Q | PWR_brick:DIOM7959X262N | D1 |
| 1 | XAL7070-332MEC | PWR_brick:XAL7070332MEC | L2 |
| 1 | cap_+ve | PWR_brick:solder_pad_2.5mmx2.5mm | C+1 |
| 1 | cap_-ve | PWR_brick:solder_pad_2.5mmx2.5mm | C-1 |

ShawnHymel/rpi-pico-debugger-shoe
Stackable debugger board for the Raspberry Pi Pico. Solder long headers to this debugger board in order to connect the Pico to it.


BerkeleyLab/Marble
Dual FMC FPGA carrier board developed for general purpose use in particle accelerator electronics instrumentation.


ts-manuel/iMX6-Demo-Board
Demo board for the i.MX6ULL Single-Core Processor with Arm Cortex-A7 Core

BetzDrive/interface-board
Power and signal conditioning board for the Betz Drive system

myles-parfeniuk/biltong_board
Sun drying emulation controller for biltong and other dried foodstuffs.

SMalasGit/2s-BMS
A repository for a 2s lithium ion BMS that utilizes the BQ28Z620. This IC is an all-in-one chip that features battery protection, cell balancing, battery charging, battery current and voltage monitoring, and gas gauging…
It measures 27.8 × 39.1 mm and has 2 copper layers, 1.6 mm thick.
42 parts, built around the LT8645SHV-2#PBF, 150060VS75000, SMCJ64A-Q and XAL7070-332MEC. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the raju-gudala/5v-Power-Module-UAV-avionics repository on GitHub, at the commit this page was made from: the board is PwrBrk5V.kicad_pcb and its schematic PwrBrk5V.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).