
LevelShifter
gusmanb/logicanalyzer
24 channel, 100Msps logic analyzer hardware and software

Fall Sensor System: IoT Firmware (ESP32 C1001/LD2410 + ATtiny85), KiCad 10.0 PCB & Schematics, and Android Companion App
Fall sensor is an open-source printed circuit board by RajatG, from the RajatG/FallSensorSystem repository on GitHub. It is a 2-layer board of 100 × 80 mm with 21 parts on 42 nets, routed with 212 tracks and 30 vias.
Its parts include 7 ICs, 5 capacitors, 3 resistors, 2 switches and 1 diode. It belongs with the sensors and measurement boards and the ESP32 and AVR (ATmega, ATtiny) boards of this library.
This directory contains the complete electronic schematic and PCB design files for the Fall Sensor System prototype (Rev A).
| File / Folder | Type | Description |
|---|---|---|
fall_sensor.kicad_sch | Schematic | Main system schematic in KiCad 10 format. |
fall_sensor.kicad_pcb | PCB Layout | 2-layer, $100.00 \times 80.00\text{ mm}$ printed circuit board layout. |
fall_sensor.kicad_pro | Project Config | KiCad project workspace and design rules. |
FallSensor.kicad_sym | Symbol Library | Custom schematic symbols for breakout modules. |
FallSensor.pretty/ | Footprint Library | Custom PCB footprints for daughterboards and sensors. |
export/ | Production Files | Manufacturing Gerbers and printable PDF packages. |
| Pin # | Label | Connected Net | Hardware Destination & Role |
|---|---|---|---|
| 1 | 3V3 | +3V3 | Regulated 3.3V power input from U7 buck converter |
| 5 | GPIO34 | /BATT_ADC | Midpoint of 100kΩ/100kΩ battery sensing divider |
| 8 | GPIO33 | Net-(U1-GPIO33) | Tactile Sync & Alarm Clear Button (SW1) |
| 9 | GPIO25 | /PRESENCE | C1001 radar hardware presence flag (OUT1) |
| 10 | GPIO26 | /FALL | C1001 radar hardware fall detection flag (OUT2) |
| 11 | GPIO27 | /RADAR_EN | Load switch gate control (energizes radar power rail) |
| 14 | GND | GND | Common system ground plane |
| 15 | GPIO13 | /PIR_WAKE | Motion wake interrupt from ATtiny85 Sentinel (PB2) |
| 19 | GPIO19 | Net-(U1-GPIO19) | Status Fall Alarm LED (D1) via 270Ω resistor |
| 26 | GPIO17 | /RADAR_RX | Hardware UART RX $\leftarrow$ C1001 radar TX |
| 27 | GPIO16 | /RADAR_TX | Hardware UART TX $\rightarrow$ C1001 radar RX |
| 28 | GPIO4 | /MIC_WAKE | Acoustic impact wake interrupt from ATtiny85 Sentinel (PB0) |
| Pin # | Label | Connected Net | Hardware Destination & Role |
|---|---|---|---|
| 2 | PB4 | Net-(U2-P4) | Digital acoustic trigger input from LM393 (DO) |
| 5 | PB1 | Net-(PIR1-OUT) | Digital motion trigger input from AM312 PIR (OUT) |
| 6 | PB0 | /MIC_WAKE | Active-HIGH 50ms wake pulse to ESP32 GPIO4 |
| 4 | PB2 | /PIR_WAKE | Active-HIGH 50ms wake pulse to ESP32 GPIO13 |
| 7 | GND | GND | Common ground |
| 8 | VIN | Unconnected | Bypassed (Digispark onboard regulator not used) |
| 9 | 5V/VCC | +3V3 | Regulated 3.3V power input from U7 buck converter |
export/fall_sensor_gerbers.zip — Ready for direct upload to JLCPCB, PCBWay, or OSH Park.export/pdf/fall_sensor_pcb_front_and_back_A4.pdf — Verified 1:1 A4 sheet with 10.0 cm calibration ruler for physical component fit-testing.export/pdf/README.md for top/bottom silkscreen and layer plots.../docs/PCB_Component_Connections_Verification.md../docs/PCB_Component_Footprints_and_Dimensions.md../docs/SMD_BOM_Master_List.md| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 0.1u | Capacitor_THT:C_Disc_D5.0mm_W2.5mm_P5.00mm | C7, C8 |
| 2 | 100k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1, R2 |
| 1 | 10u | Capacitor_THT:C_Disc_D5.0mm_W2.5mm_P5.00mm | C1 |
| 1 | 22u | Capacitor_THT:C_Disc_D5.0mm_W2.5mm_P5.00mm | C4 |
| 1 | 270 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R3 |
| 1 | 470u | Capacitor_THT:CP_Radial_D8.0mm_P3.50mm | C3 |
| 1 | AM312_PIR | FallSensor:AM312_PIR_Square22x20 | PIR1 |
| 1 | BATTERY_PADS | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | BT1 |
| 1 | Buck Converter | FallSensor:LM2596_Module | U7 |
| 1 | C1001_Radar | FallSensor:C1001_Module | RADAR1 |
| 1 | Digispark_ATtiny85 | Digispark_9Pin_RightAngle | U2 |
| 1 | ESP32_DevKit_V1 | FallSensor:ESP32_DevKit_DOIT_2x15 | U1 |
| 1 | LATCH_PWR | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | SW2 |
| 1 | LED | LED_THT:LED_D3.0mm | D1 |
| 1 | LM393_Sound_Module | FallSensor:LM393_Sound_Module | U5 |
| 1 | LoadSwitch_DBVT | DIP-6_W10.16mm | U6 |
| 1 | MT3608_Module | FallSensor:MT3608_Module | U3 |
| 1 | SYNC | Button_Switch_THT:SW_PUSH_6mm | SW1 |
| 1 | TP4056_Module | FallSensor:TP4056_Module | U4 |

gusmanb/logicanalyzer
24 channel, 100Msps logic analyzer hardware and software

mntmn/amiga2000-gfxcard
MNT VA2000, an Open Source Amiga 2/3/4000 Graphics Card (Zorro II/III), written in Verilog


hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

drandyhaas/KiCadRoutingTools
A set of Python/Rust tools to aid routing in KiCad

Arrow-air/project-quiver
Project Quiver documentation, designs, and project artifacts.


It measures 100 × 80 mm and has 2 copper layers, 1.6 mm thick.
21 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the RajatG/FallSensorSystem repository on GitHub, at the commit this page was made from: the board is hardware/fall_sensor.kicad_pcb and its schematic hardware/fall_sensor.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask RajatG before reusing the design.