
Commodore Vic-20
jimbro1000/Commodore-Vic-20
Late, cost reduced vic-20 schematic and board

Capture and write Commodore tapes via USB device
TapeXUM is an open-source printed circuit board by r1me, from the r1me/TapeXUM repository on GitHub. It is a 2-layer board of 62.4 × 34.4 mm with 21 parts on 18 nets, routed with 95 tracks and 2 vias.
It is built around the 2SD880. Its parts include 4 resistors, 4 diodes, 3 connectors, 2 capacitors and 2 transistors. It belongs with the AVR (ATmega, ATtiny) boards of this library.
TapeXUM is a USB device that can read and write to cassettes of Commodore 16/64/VIC-20 (read and write) and ZX Spectrum (read only) format. It requires a Commodore datasette connected to it. This project is based on ZoomTape by Arnd Menge, a great idea and originally a part of OpenCBM package. TapeXUM uses Arduino Pro Micro and through hole components so it's a DIY friendly design.
Huge thanks to Data/Tropyx for creating enclosure design for 3D printing!

| Component | qty |
|---|---|
| Arduino Pro Micro 5V | 1 |
| 1/4W Resistor for LEDs (~1K, depending on your preference) | 2 |
| 1/4W 1K Resistor | 1 |
| 1/2W 1.5k Resistor | 1 |
| 2N3904 Transistor | 1 |
| 2SD880 or 2SD313 Transistor | 1 |
| 3mm LED (i.e. green and red) | 2 |
| 6V8 Zener diode | 1 |
| 1N400x diode | 1 |
| 1uF electrolytic capacitor | 1 |
| 0.1uF electrolytic capacitor | 1 |
| Barrel jack DC connector 2.1/5.5mm or 2.5/5.5mm | 1 |
| 1x3 pin header 2.54mm and a jumper | 1 |
| 9VDC 500mA power supply with DC connector (center positive) | 1 |
| Micro USB cable | 1 |
Windows 7/10 64-bit libraries and tools: https://github.com/r1me/TapeXUM/releases/download/1.0/xum-installer-x64.zip
Get PCB's from PCBWay: https://www.pcbway.com/project/shareproject/TapeXUM___Capture_and_write_Commodore_tapes_via_USB_device.html
Gerber and Kicad files (hardware design): https://github.com/r1me/TapeXUM/tree/main/hardware
Firmware for Arduino Pro Micro: https://github.com/r1me/TapeXUM/tree/main/firmware
3D enclosure: https://www.thingiverse.com/thing:4659235
OpenCBM: https://github.com/r1me/OpenCBM
avrdude -p m32u4 -c avr109 -P comX -U flash:w:xum1541-PROMICRO_TAPE-v08.hex
TapeXUM follows same license for software as OpenCBM. PCB design of TapeXUM is free and shared under CERN OHW v2 (open hardware licence).
| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | R | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1, R4 |
| 1 | .1uF | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C2 |
| 1 | 1K5 1/2W | Resistor_THT:R_Axial_DIN0309_L9.0mm_D3.2mm_P12.70mm_Horizontal | R2 |
| 1 | 1N4004 | Diode_THT:D_DO-41_SOD81_P10.16mm_Horizontal | D1 |
| 1 | 1uF | Capacitor_THT:CP_Radial_D4.0mm_P2.00mm | C1 |
| 1 | 2N3904 | Package_TO_SOT_THT:TO-92_Inline | Q2 |
| 1 | 2SD880 | Package_TO_SOT_THT:TO-220-3_Horizontal_TabDown | Q1 |
| 1 | 330R | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R3 |
| 1 | 6V8 | Diode_THT:D_DO-35_SOD27_P10.16mm_Horizontal | D3 |
| 1 | Conn_01x02 | Connector_BarrelJack:BarrelJack_Horizontal | J2 |
| 1 | Conn_01x06 | TapeXUM:conn_datasette2 | J1 |
| 1 | DEBUG | Connector_PinHeader_1.27mm:PinHeader_1x03_P1.27mm_Vertical | J3 |
| 1 | MOTOR | LED_THT:LED_D3.0mm | D2 |
| 1 | POWER | LED_THT:LED_D3.0mm | D4 |
| 1 | ProMicro | TapeXUM:ProMicro | U1 |
| 1 | VDC INPUT | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | JP1 |
| 1 | rime_logo_5mm_b_cu | TapeXUM:rime_logo_5mm_b_cu | G*** |
The 18 most common of 21 parts.

jimbro1000/Commodore-Vic-20
Late, cost reduced vic-20 schematic and board


dslmande/TR-808PSU
UNTESTED KiCad rebuild of the Roland TR-808 power supply board PS3116 in two versions: 230 V (PS3116-054) and 110 V (PS3116-051). Not manufactured, not safety-tested.

sjgray/V364-Remake
Project to recreate the never-released Commodore V364 computer


gusmanb/logicanalyzer
24 channel, 100Msps logic analyzer hardware and software

mntmn/amiga2000-gfxcard
MNT VA2000, an Open Source Amiga 2/3/4000 Graphics Card (Zorro II/III), written in Verilog

It measures 62.4 × 34.4 mm and has 2 copper layers, 1.6 mm thick.
21 parts, built around the 2SD880. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the r1me/TapeXUM repository on GitHub, at the commit this page was made from: the board is hardware/TapeXUM.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask r1me before reusing the design.