Skip to the content
4 layers90 × 76.6 mmMicro core, the printed circuit board in 3D

Core EFI Micro Core — Hellen-One rusEFI ECU, 35-way AMPSEAL, vertical header

Size
90 × 76.6 mm
Copper layers
4
Thickness
1.6 mm
Parts
49
Nets
69
Pads
418
Tracks, vias
1,144, 107
Pours
4
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
13 Sep 2026
Updated
26 Sep 2026

Overview

Micro core is an open-source printed circuit board by quintinbannink42, from the quintinbannink42/micro-core repository on GitHub. It is a 4-layer board of 90 × 76.6 mm with 49 parts on 69 nets, routed with 1,144 tracks and 107 vias.

It is built around the SLM27524CA-DG, NCE4080K and SMAJ33A, with the US1M among its other parts. Its parts include 14 diodes, 11 resistors, 8 capacitors, 7 transistors and 4 ICs.

Main components

4

README

README.md

Micro Core

Core EFI Hellen-One rusEFI ECU. Microsquirt-class sealed box, 35-way AMPSEAL, vertical header.

4-cylinder sequential wire-in. STM32F407VGT6 on Hellen mega-mcu100/0.3 (not mega-mcu64). Seven NCE4080K power FETs: 4 injector channels (2× high-Z each) plus fuel-pump, idle, and boost low-sides with US1M flyback and SMAJ33A. Gates are driven from /V12_RAW by SLM27524CA-DG low-side drivers, not directly from the 3.3 V GPIO.

Status

Spec locked in docs/SPEC.md. Hardware on this branch: rev q. Q1–Q7 are NCE4080K (LCSC C191380) on the existing DPAK land. Four SLM27524CA-DG drivers (LCSC C2921387) take the mega-mcu100 GPIO and drive the gates from /V12_RAW through the 12 ohm series resistors. Seven of eight channels are used; the spare input is tied to GND. Q5–Q7 (AMPSEAL pins 8/9/10, FP / Idle / Boost) keep the US1M flyback and SMAJ33A from rev p. F407VGT6 on mega-mcu100 stays. boards/microcore-q/ lands when Create Board succeeds on main after merge. See docs/HARDWARE_STATUS_rev_q.md. Not production-ready. The earlier FET comparison is in docs/FET_COMPARISON.md.

  • Header: TE 776231-1 (straight / vertical)
  • Plug: TE 776164-1 black, key A
  • Not 776163-1 (right-angle)
  • USB: vertical Mini-B on the frame (hellen-one-common:USB_B_Mini / USB-MINI-B-VERTICAL), gasketed flap or pigtail — not on the 35-way AMPSEAL

Spec

See docs/SPEC.md. Boss brief: MICROCORE_BRIEF.md.

Hellen tips: docs/HELLEN-FAQ.md.

Firmware board name: coreefi_micro (sibling tree /workspace/fw-coreefi-micro, not in this repo). The MCU is the F407 from rev n; that firmware tree will need an F407 target later. This repo does not publish a firmware remote.

KiCad board basename: microcore (BOARD_PREFIX=micro, BOARD_SUFFIX=core, rev q).

Hellen tooling

  • Submodules: hellen-one (andreika-git/hellen-one), kicad6-libraries (rusefi/kicad6-libraries)
  • CI: Create Board on push to main; daily submodule update workflows
  • Fab outputs on main include boards/microcore-p/. After merge, Create Board writes boards/microcore-q/
  • Local DRC needs KiCad 10 (kicad-cli); board file is generator_version 10.0
  • Empty-PCB guard: bin/check-pcb-not-empty.sh (Create Board job guard-pcb-not-empty)

License

Hardware and docs in this repo: use for Core EFI product development. Firmware will track rusEFI (GPL) when the board config lands.

Parts

49
QtyValueFootprintReferences
1112R0603R1, R2, R3, R4, R5, R6, R7, R8, R9, R10, R11
7NCE4080KDPAKQ1, Q2, Q3, Q4, Q5, Q6, Q7
7SMAJ33ADO214ACD5, D6, D7, D8, D12, D13, D14
7US1MDO214ACD1, D2, D3, D4, D9, D10, D11
4100nmicrocore-fp:C0603C1, C3, C5, C7
41umicrocore-fp:C0603C2, C4, C6, C8
4SLM27524CA-DGmicrocore-fp:SOIC-8U1, U2, U3, U4
1Module-power_12and5V-0.3hellen-one-power_12and5V-0.3:power_12and5VM2
1Module-vr-max9924-0.3hellen-one-vr-max9924-0.3:vr-max9924M3
1Module:mega-mcu100/0.3hellen-one-mega-mcu100-0.3:mega-mcu100M1
1TE_776231-1kicad6-libraries:TE_776231J1
1USB_B_Minihellen-one-common:USB-MINI-B-VERTICALJ8

Similar boards

  • 4 layers36.7 × 49 mmMegadesk companion, the printed circuit board in 3D

    Megadesk companion

    gcormier/megadesk_companion

    companion board for megadesk to add smarthome functionality

    35 parts27
  • 2 layers120.4 × 85.7 mmESPrinkler Retic PCB, the printed circuit board in 3D

    ESPrinkler Retic PCB

    slippery-carrot/ESPrinkler-Retic-Controller

    8-Zone reticulation controller based on ESPHome for Home Assistant

    142 parts6GPL-3.0
  • 4 layers87.6 × 46.7 mmModbus to x, the printed circuit board in 3D

    Modbus to x

    joachimda/modbus-to-x

    ESP32 based hardware and firmware stack that bridges modbus RTU devices to modern network services.

    58 parts5MIT
  • 4 layers100 × 50 mmChronolog, the printed circuit board in 3D

    Chronolog

    slemanz/chronolog

    STM32-based temperature data logger with RTC, NOR flash storage, LCD and Wi-Fi. Hardware and firmware.

    95 parts5
  • 2 layers155 × 78 mm4F5LCD, the printed circuit board in 3D

    4F5LCD

    Code99it/4F5LCD

    88 parts3
  • 2 layers49.5 × 29 mmXESC YF r4, the printed circuit board in 3D

    XESC YF r4

    ClemensElflein/xESC_YF_rev4-adapter

    [![Contributors][contributors-shield]][contributors-url] [![Forks][forks-shield]][forks-url] [![Stargazers][stars-shield]][stars-url] [![Issues][issues-shield]][issues-url] [![MIT License][license-shield]][license-url]

    54 parts2MIT
  • 4 layers95 × 43 mmReflow Plate Controller, the printed circuit board in 3D

    Reflow Plate Controller

    incend1um3/USB-C-PD-Reflow-Plate

    300W PCB Reflow Plate with USB-C PD Support

    83 parts2CERN-OHL-S-2.0
  • 2 layers100 × 55 mmWellD, the printed circuit board in 3D

    WellD

    kinggh0stee/WellD

    ESP32-C6 Zigbee well monitor — reads a 4–20 mA pressure transducer and DS18B20, reports water level, temperature, and battery to Zigbee2MQTT with OTA update support

    122 parts2MIT

Questions

How big is the Micro core PCB?

It measures 90 × 76.6 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Micro core use?

49 parts, built around the SLM27524CA-DG, NCE4080K, SMAJ33A and US1M. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Micro core KiCad files?

From the quintinbannink42/micro-core repository on GitHub, at the commit this page was made from: the board is microcore.kicad_pcb and its schematic ANALOG.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Micro core design in my own project?

Its repository states no licence, so its author keeps all rights: ask quintinbannink42 before reusing the design.