Skip to the content
2 layers120.9 × 93.7 mmEsp32 hw130 adapter, the printed circuit board in 3D

ESP32 DVD pen plotter with HW-130 L293D shield: custom firmware, socket-plug wiring, USB/Bluetooth G-code

Size
120.9 × 93.7 mm
Copper layers
2
Thickness
1.6 mm
Parts
4
Nets
49
Pads
64
Tracks, vias
39, 27
Pours
2
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
29 Jul 2026
Updated
16 Aug 2026

Overview

Esp32 hw130 adapter is an open-source printed circuit board by priyanshuchawda, from the priyanshuchawda/esp32-dvd-plotter repository on GitHub. It is a 2-layer board of 120.9 × 93.7 mm with 4 parts on 49 nets, routed with 39 tracks and 27 vias.

It belongs with the interfaces and adapters boards and the ESP32 boards of this library.

README

README.md

ESP32 / Uno DVD Pen Plotter

DVD-drive sleds on an HW-130 L293D shield. Both boards are supported in separate folders — swap hardware, keep the same G-code tools.

DocContents
docs/STATUS.mdDone vs left checklist
docs/ARCHITECTURE.mdHow the system fits together
FINDINGS.mdMeasured bed, steps/mm, coil ohms
hardware/WIRING.mdESP32 jumper wiring (no soldering)
cad/pcb/ESP32↔HW-130 adapter PCB (Uno-style stack + Gerbers)
src/README.mdFirmware folder map

Pipeline

Firmware folders

PathBoard
src/uno/uno_plotterArduino Uno (shield stacked)
src/esp32/esp32_plotterESP32 (jumpers into shield headers)

Bed: 55 × 50 mm · steps/mm: 2.058 · baud: 115200

ESP32 quick start (current focus)

  1. Shield off the Uno. Power shield 5V+GND and EXT_PWR (yellow jumper off). Common GND with ESP32. See hardware/WIRING.md.
  2. Eight jumpers: D12/D4/D7/D8 + D11/D3/D6/D5 → ESP32 GPIOs in the wiring table.
  3. Flash and test:
bash
arduino-cli compile -b esp32:esp32:esp32 src/esp32/esp32_plotter
arduino-cli upload  -b esp32:esp32:esp32 -p /dev/ttyUSB0 src/esp32/esp32_plotter

# USB serial: $COILTEST then raise $POWER= if needed
tools/send_gcode.py -p /dev/ttyUSB0 -b 115200 test-square-uno.gcode

Wi-Fi hotspot DVD-Plotter / plotter123 → draw in the browser.

Uno quick start

bash
arduino-cli compile -b arduino:avr:uno src/uno/uno_plotter
arduino-cli upload  -b arduino:avr:uno -p /dev/ttyACM0 src/uno/uno_plotter
tools/send_gcode.py -p /dev/ttyACM0 -b 115200 test-square-uno.gcode

Making G-code

ToolUse
tools/text2gcode.pyHershey single-stroke text
tools/handwriting2gcode.pyNeural handwriting
tools/image2gcode.pyBitmap → outlines
tools/send_gcode.pyUSB stream
python3 sim/simulate.py job.gcode --paperPaper preview

Parts

4
QtyValueFootprintReferences
1DevKit_LEFTPinSocket_1x15_P2.54mm_VerticalJ_ESP_L
1DevKit_RIGHTPinSocket_1x15_P2.54mm_VerticalJ_ESP_R
1EXT_5VTerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_HorizontalJ_5V
1UNO_R3_HEADERSArduino_UNO_R3J_SHIELD

Similar boards

  • 2 layers18.5 × 26 mm24g2usb rp2350zero, the printed circuit board in 3D

    24g2usb rp2350zero

    joypad-ai/joypad-os

    Universal controller firmware for building adapters, dongles, and custom controllers.

    4 parts1.7kApache-2.0
  • 2 layers116 × 33 mm966595-1 and 963356-1, the printed circuit board in 3D

    966595-1 and 963356-1

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    4 parts1.2k
  • 2 layers19 × 18 mmDaughter board, the printed circuit board in 3D

    Daughter board

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    4 parts915
  • 2 layers24.8 × 24.8 mmNrf24 breakout, the printed circuit board in 3D

    Nrf24 breakout

    tardate/LittleArduinoProjects

    a collection of "Little Electronic & Arduino Projects", most involving electronics or an Arduino in one way or another!

    4 parts803MIT
  • 2 layers26 × 20 mmCap chain, the printed circuit board in 3D

    Cap chain

    drandyhaas/KiCadRoutingTools

    A set of Python/Rust tools to aid routing in KiCad

    4 parts744MIT
  • 2 layers34.7 × 20 mmXG Station Power MSI, the printed circuit board in 3D

    XG Station Power MSI

    osy/XG_Mobile_Station

    Open source eGPU dock for ROG Ally and ROG Flow

    4 parts712CC-BY-4.0
  • 2 layers20.3 × 24.5 mmJack power input, the printed circuit board in 3D

    Jack power input

    Luos-io/luos_engine

    Open-source and real-time orchestrator for cyber-physical-systems, to easily design, test and deploy embedded applications and digital twins.

    4 parts546MIT

Questions

How big is the Esp32 hw130 adapter PCB?

It measures 120.9 × 93.7 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Esp32 hw130 adapter use?

4 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Esp32 hw130 adapter KiCad files?

From the priyanshuchawda/esp32-dvd-plotter repository on GitHub, at the commit this page was made from: the board is cad/pcb/esp32_hw130_adapter/esp32_hw130_adapter.kicad_pcb and its schematic cad/pcb/esp32_hw130_adapter/esp32_hw130_adapter.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Esp32 hw130 adapter design in my own project?

Its repository states no licence, so its author keeps all rights: ask priyanshuchawda before reusing the design.