

STM32F1 based Flight Controller with 9dof IMU (LSM9DS1) and serial 32M Flash
- Size
- 45 × 45 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 58
- Nets
- 79
- Pads
- 238
- Tracks, vias
- 546, 72
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 8 Jun 2019
- Updated
- 8 Jun 2019
Overview
FC V2 is an open-source printed circuit board by prashanthmypadi, from the prashanthmypadi/STM32FC repository on GitHub. It is a 2-layer board of 45 × 45 mm with 58 parts on 79 nets, routed with 546 tracks and 72 vias.
It is built around the STM32F103C8T6, CP2102N-EK and AMS1117-3.3, with the LSM9DS1 and BAT54C among its other parts. Its parts include 20 capacitors, 10 resistors, 9 connectors, 6 ICs and 3 diodes. It belongs with the STM32 boards of this library.
Main components
5STM32F103C8T6
LQFP-48(7x7)-40℃~+85℃ 12bit 20KB 2V~3.6V 32 Bit 37 64KB 72MHz ARM Cortex-M3 Built-in FLASH LQFP-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)CP2102N-EK
-- USB Conversion Modules ROHSSilicon LabsUSB Conversion ModulesAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsLSM9DS1
LGA-24(3x3.5)-40℃~+85℃ 1.9V~3.6V 16bit Accelerometer Gyroscope SPI、I2C X,Y,Z X,Y,Z ±16g ±2000dps LGA-24(3x3.5) Accelerometers ROHSSTMicroelectronicsAccelerometersBAT54C
SOT-231 Pair Common Cathode 200mA 2uA@25V 30V 600mA 800mV@100mA SOT-23 Schottky Diodes ROHSNexperiaSchottky Diodes
README
README.mdSTM32FC
STM32F1 based Flight Controller with 9dof IMU (LSM9DS1) and serial 32M Flash. Upto 4 servo outputs. PPM RC input Connectors for external UART and I2C modules. Battery Voltage monitoring.
Parts
58| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | 100n | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C1, C2, C3, C4, C7, C8, C13, C15, C17, C18, C21 |
| 4 | MountingHole | MountingHole:MountingHole_2.5mm | H1, H2, H3, H4 |
| 3 | 10k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R1, R2, R5 |
| 3 | 1u | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C5, C9, C10 |
| 2 | 10n | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C20, C22 |
| 2 | 10u | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C6, C19 |
| 2 | 1k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R8, R11 |
| 2 | 330 | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R9, R10 |
| 2 | 4.7u | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C14, C16 |
| 2 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2, U3 |
| 1 | 22.1k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R6 |
| 1 | 41.2k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R4 |
| 1 | 47.5k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R7 |
| 1 | BAT54C | Package_TO_SOT_SMD:SOT-23 | D1 |
| 1 | BOOT | Button_Switch_SMD:SW_SPST_EVQP2 | SW1 |
| 1 | Batt | Connector_JST:JST_EH_B02B-EH-A_1x02_P2.50mm_Vertical | J3 |
| 1 | CP2102N | Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm | U5 |
| 1 | I2C | Connector_PinHeader_1.27mm:PinHeader_1x04_P1.27mm_Vertical | J9 |
| 1 | LD1 | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D3 |
| 1 | LSM9DS1 | Package_LGA:LGA-24L_3x3.5mm_P0.43mm | U6 |
| 1 | M1 | Connector_PinHeader_1.27mm:PinHeader_1x03_P1.27mm_Vertical | J4 |
| 1 | M2 | Connector_PinHeader_1.27mm:PinHeader_1x03_P1.27mm_Vertical | J5 |
| 1 | M25PX32 | Package_SO:SOIJ-8_5.3x5.3mm_P1.27mm | U4 |
| 1 | M3 | Connector_PinHeader_1.27mm:PinHeader_1x03_P1.27mm_Vertical | J6 |
| 1 | M4 | Connector_PinHeader_1.27mm:PinHeader_1x03_P1.27mm_Vertical | J7 |
| 1 | MS621F | Battery:BatteryHolder_Seiko_MS621F | BT1 |
| 1 | POWER | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D2 |
| 1 | PPM | Connector_PinHeader_1.27mm:PinHeader_1x03_P1.27mm_Vertical | J1 |
| 1 | RESET | Button_Switch_SMD:SW_SPST_EVQP2 | SW2 |
| 1 | SG-5032CA | Oscillator:Oscillator_SMD_SeikoEpson_SG8002LB-4Pin_5.0x3.2mm_HandSoldering | X1 |
| 1 | STM32F103C8T6 | Package_QFP:LQFP-48_7x7mm_P0.5mm | U1 |
| 1 | UART | Connector_PinHeader_1.27mm:PinHeader_1x04_P1.27mm_Vertical | J8 |
| 1 | USB | Connector_USB:USB_Micro-B_Wuerth_629105150521_CircularHoles | J2 |
| 1 | vyoma logo | logo:Vyoma | G*** |
The 57 most common of 58 parts.
Similar boards
- 2 layers145 × 165 mm

- 4 layers160 × 73.2 mm

MainPCB
doppelgrau/esp32-f9p-io-board
An IO-PCB (two motor-driver/H-bridge, CAN, RS232, ADS1115, relay, ethernet, ardusimple f9p compatible connector) with an ESP32 for 12V power, three 15V tolerant analog inputs, three 5V tolerant inputs.
162 parts39 - 4 layers29 × 69.8 mm

- 2 layers110 × 100 mm

PidginTranslator
DevMubarak1/PidginTranslator
Handheld translator for Nigerian languages. No internet needed for common phrases, YarnGPT for everything else.
14 parts21MIT - 2 layers54 × 68 mm

OpenSTM32F4 LQFP64
phonght32/openSTM32F4_LQFP64
openSTM32 board using STM32F4 LQFP64 package. This board designed to perform base control for SLAM and Navigation.There are also many availabe connectors that meet many other application requirements.
77 parts7MIT - 4 layers121 × 60 mm

- 2 layers45.7 × 60.2 mm

Pcb watch
nithinmathewjoji/Schrodinger-Clock-PCB-Watch-
An open-source ESP32-S3-based smartwatch with RTC, I2C display, buzzer, LEDs, and battery monitoring. Designed using KiCad, it features a compact PCB layout, Li-Po battery support, and USB charging
58 parts4MIT - 4 layers48.2 × 54.1 mm

ESP32
apoorvarshneya/ESP32_DevBoard
Designed and developed a custom ESP32 Development Kit from scratch using KiCad, featuring USB-to-Serial programming, 5V-to-3.3V power regulation, reset/boot buttons, LEDs, GPIO headers, and selectable power inputs.
48 parts
Questions
How big is the FC V2 PCB?
It measures 45 × 45 mm and has 2 copper layers, 1.6 mm thick.
What parts does the FC V2 use?
58 parts, built around the STM32F103C8T6, CP2102N-EK, AMS1117-3.3 and LSM9DS1. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the FC V2 KiCad files?
From the prashanthmypadi/STM32FC repository on GitHub, at the commit this page was made from: the board is STM32FC/FC V2.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the FC V2 design in my own project?
Its repository states no licence, so its author keeps all rights: ask prashanthmypadi before reusing the design.