
Rpi hat
ppetr/home-automation-CAN
SW and HW for an inexpensive home automation communication network based on the CAN bus

SW and HW for an inexpensive home automation communication network based on the CAN bus
Rj45can power is an open-source printed circuit board by ppetr, from the ppetr/home-automation-CAN repository on GitHub, published under the Apache-2.0 licence. It is a 2-layer board of 60 × 50 mm with 53 parts on 48 nets, routed with 433 tracks and 75 vias.
It is built around the ESP32-WROOM-32D, SN65HVD235D and PMEG6010CEJ. Its parts include 15 resistors, 7 capacitors, 7 diodes, 7 connectors and 4 ICs. It belongs with the interfaces and adapters boards and the ESP32 boards of this library.
Provides CAN interface using the standard D-sub DE-9 connector and our custom RJ-45 connector.
The board should comply to the requirements stated in https://github.com/raspberrypi/hats. If you encounter any violation or deviation, please open an issue.
The schema is loosely based on https://www.disk91.com/2015/technology/hardware/design-a-raspberry-pi-hat-shield/
| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 100 | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R6, R7, R8, R9, R10 |
| 4 | MountingHole | MountingHole:MountingHole_2.2mm_M2 | H1, H2, H3, H4 |
| 4 | PMEG6010CEJ | Diode_SMD:D_SOD-323F | D1, D2, D3, D4 |
| 3 | 330 | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R13, R16, R17 |
| 3 | LED | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D5, D6, D7 |
| 2 | 10uF | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C6, C8 |
| 2 | 120 | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R11, R12 |
| 2 | 1uF (50V) | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C2, C4 |
| 2 | NoTerminator | Jumper:SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mm | JP6, JP9 |
| 2 | Terminator | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | JP7, JP8 |
| 1 | 100K | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R5 |
| 1 | 100k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R3 |
| 1 | 100nF | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C5 |
| 1 | 10k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R1 |
| 1 | 10nF | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C1 |
| 1 | 2k5 | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R2 |
| 1 | 33uH | Inductor_SMD:L_Coilcraft_LPS4018 | L1 |
| 1 | 4.7uF (50V) | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C7 |
| 1 | 5k6 | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R4 |
| 1 | 7-48V | Connector_BarrelJack:BarrelJack_Horizontal | J1 |
| 1 | Boot option | TestPoint:TestPoint_2Pads_Pitch2.54mm_Drill0.8mm | JP2 |
| 1 | CAN DE-9 | Connector_Dsub:DSUB-9_Male_Horizontal_P2.77x2.84mm_EdgePinOffset4.94mm_Housed_MountingHolesOffset7.48mm | J3 |
| 1 | ESP32-WROOM-32D | RF_Module:ESP32-WROOM-32 | U1 |
| 1 | GPIO-B | Connector_JST:JST_SH_BM07B-SRSS-TB_1x07-1MP_P1.00mm_Vertical | J6 |
| 1 | JTAG | Connector_IDC:IDC-Header_2x05_P2.54mm_Vertical | J4 |
| 1 | MAX15062A | Package_DFN_QFN:DFN-8_2x2mm_P0.5mm | U3 |
| 1 | MAX17610 | rj45can-power:MAX17610 | U2 |
| 1 | No power | Jumper:SolderJumper-2_P1.3mm_Open_TrianglePad1.0x1.5mm | JP1 |
| 1 | RESET | Button_Switch_SMD:SW_SPST_FSMSM | SW1 |
| 1 | RESET/~EN | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | JP3 |
| 1 | RJ45_Shielded | Connector_RJ:RJ45_Ninigi_GE | J5 |
| 1 | SN65HVD235 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U4 |
| 1 | UART | Connector_JST:JST_SH_BM03B-SRSS-TB_1x03-1MP_P1.00mm_Vertical | J2 |
| 1 | qwiic/GPIO-A | Connector_JST:JST_SH_BM04B-SRSS-TB_1x04-1MP_P1.00mm_Vertical | J8 |

ppetr/home-automation-CAN
SW and HW for an inexpensive home automation communication network based on the CAN bus

ppetr/home-automation-CAN
SW and HW for an inexpensive home automation communication network based on the CAN bus




Kevpamm/PCB-PLL-ADF4159
This git repository tracks the design and development of the PCB for a phase-locked loop (PLL) system centered around the ADF4159 IC




punkfab/pcb-corpus
235 real KiCad boards from open-source hardware repositories, prepared as a placement and routing benchmark
It measures 60 × 50 mm and has 2 copper layers, 1.6 mm thick.
53 parts, built around the ESP32-WROOM-32D, SN65HVD235D and PMEG6010CEJ. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the ppetr/home-automation-CAN repository on GitHub, at the commit this page was made from: the board is power/rj45can-power.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the Apache-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).