Skip to the content
2 layers261 × 18 mmSynth, the printed circuit board in 3D

This work is licensed under a [Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License][cc-by-nc-sa].

Size
261 × 18 mm
Copper layers
2
Thickness
1.6 mm
Parts
19
Nets
18
Pads
100
Tracks, vias
155, 0
Pours
2
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
7 Apr 2026
Updated
8 Apr 2026

Overview

Synth is an open-source printed circuit board by povle, from the povle/spark-synth-hardware repository on GitHub. It is a 2-layer board of 261 × 18 mm with 19 parts on 18 nets, routed with 155 tracks and 0 vias.

It belongs with the audio and music boards of this library.

README

README.md

CC BY-NC-SA 4.0

This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.

CC BY-NC-SA 4.0

Spark Synth - Hardware

This repo is intended to host the hardware files and assembly information for Spark - an open-source portable ESP32-based synth.

Important disclaimer: currently, this project is a prototype. If you really want to assemble it yourself, be prepared for a lot of drilling, sanding, double-sided-taping, soldering tiny wires and figuring stuff out on your own. You can contact me on Reddit and I might help if I have the time for that, but no guarantees here.

Moving forward I'm planning to design an easier to assemble V2 with everything mounted on custom PCBs, but I can't provide any timeline on that.

Feel free to modify and improve the design, but respect the licensing.

Electronics - Bill of Materials

ComponentFunctionComments
ESP-32 S3 N16R8MicrocontrollerI've used some no-name devboard marked "S3 AI". Note the "N16R8" - the project does need a lot of PSRAM.
PCM 5102ADAC
PAM8403Amp
RV09 (10 kOhm) (x16)PotentiometersNot sure what the exact model is, but mine are vertical with a plastic 12 mm long knurled shaft.
YANJUXING 4020 4 Ohm 3WSpeakerFound it on Aliexpress. It's rectangular, 40mm x 20 mm, 14.3 mm tall. The dimensions are critical, it's a pretty tight fit.
Adafruit USB-C breakout boardUSB-CAny peripheral breakout board you can find that has both power and data will do. I've used a copy of this one. Ideally look for one with 5.1k pull-down resistors on CC1 and CC2 preinstalled, so that you are not limited to Type A - Type C cables.
TP-4056Battery charger
CKCS BS015V Boost converterGiven that it's only connected to the ESP, you probably should better look for a 3.7 - 3.3V stepdown converter and power it via the 3.3V pin directly. That should be quite a bit more efficient.
Custom PCB for PotsPotentiometer wiringYou can find the KiCad project in the repo. Not essential, you could just print a mounting plate and deadbug wire all the pots to the multiplexer, but I'm not sure how well the wires will fit, there's not a lot of space there.
CD74HC4067Analog multiplexer for the pots
On-off switch
ICS 43434MicrophoneOptional, used only for the sampler.
B103 10K 5Pin 16x2Volume wheelNote the 5 pins. Important if you want stereo line out.
TLZWLA PJ-3073.5 mm socketImportant to get a switching socket.
184x74x3.5 mm Li-ion battery (5000 mAh)BatteryTAKE PROPER PRECAUTIONS WHEN WORKING WITH THESE! Only use batteries with a built-in protection circuit, take extreme care not to short circuit or damage them. I've designed the whole project around these dimensions, so your battery MUST NOT exceed them. Carefully check the clearances during assembly.
Keychron Low Profile Silent Red (x28)Keyboard switchesI think any low-profile switches with Cherry stems will work? Not sure if they are all exactly the same dimensions.
1N4148 (x28)Diodes for the keyboard matrix
MCP23017I2C IO Expander for the keyboardTechnically optional, i've only used it to minimize the amount of wiring between the top case and the bottom case. I think that ESP32 has enough pins left to connect the keyboard matrix directly, but that will make the wiring even more of a mess.
128x64 0.96 I2C OLEDDisplayThere seem to be a lot of variants with slightly different mounting dimensions, so you might have to redesign the control panel for your specific one. Or just use double sided tape.
4.5x4.5x7 mm button (x4)Control panel buttonsThese were an afterthought. They don't feel that nice, are tiny but still barely fit. This should definitely be redesigned.
GPD WIN 3 JoystickJoystickI bought this because it was the only one i could fit when i was planning to use the Korg Nanokey PCB for the keybed. Now there's a lot more space inside, so it should be doable to redesign it for something more common.
FPC 6 Pin 0.5 mm Breakout BoardBreakout for the GPD joystick

Hardware - Bill of materials

ComponentFunctionComments
3D printer3D printingI've designed the project around my Bambu Lab A1 Mini, so almost any printer will be big enough.
M3x6x5 Heat insert (x4)Connecting the case halvesI've screwed up (pun intended) with the top-right one, under the potentiometer recess. It pokes through the case (you can even see that in the photos). This should be redesigned. There's also a hole for a fifth heat insert in the center of the top case, but that would go straight through the battery.
M3x12 Screw (x4)Connecting the case halves
M2x2x3 Heat insert (x10)Connecting the keyboard plate to the top caseThey are TINY. I had to screw an M2 bolt in and heat up the whole thing with a soldering iron so that no plastic gets on the threads.
M2 Screw (x10)Connecting the keyboard plate to the top caseI've had to cut them down to specific lengths so they fit...
eSun PLA+ WhiteStructural componentsMaybe switching to PETG would be a good idea.
Bambu Lab Pla Matte (Sky Blue)Everything blue

3D printed parts

For now I'm providing them as a .3mf project, I will upload the .STEP files to the repo upon request (not sure if anyone will actually want to modify any of this),

Bottom case

Consists of 3 parts: bottom_left, bottom_right, bottom_dovetail. I've used a lot of CA glue to connect them. No supports needed, default 15% infill settings seem fine.

Bottom case

You will note that it's just a plain tub with no attachments for the components. I've printed it as a prototype to check how all my components and wires fit IRL and just stuck with it, using double-sided tape for securing most components. For the ones that need a stronger connection I've either hand drilled holes for M2 screws or used CA glue.

I'm sure I could do a much better job with wire management here, but I'm not touching this with a 10-foot pole until something breaks.

There are mounting holes for an IO side panel, but I still haven't designed one.

Some of the bottom screw holes are slightly wrong, because the version of the bottom case was designed for a different iteration of the top case. Can be fixed with a drill.

Keyboard mounting plate

Consists of two independent parts: keyboard_left and keyboard_right. They are not initially attached to each other, both will be held in place when connected to the top case. After that you can glue them together with the connecting plate.

Keyboard

Note that the switches are attached sideways for better stability and easier wiring.

Top case

Top case This is the most complicated part of the build. The main part of it consists of two halves glued together with a thin dovetail plate. The control panel is simply held in with friction, you could add a dab of glue if needed.

The keys are wired in a 5x6 matrix with the rows and the columns connected to an IO expander. I've made traces using copper tape thinking that it would make the wiring cleaner. I really don't think that it did. I would advise to just use thin wire.

The buttons are wired directly to the 5 remaining pins on the expander. They are mounted on a screwed-in piece of perfboard.

Top case covered

I've printed thin covers so that the keyboard doesn't get shorted with something in the bottom case.

Top of Spark A lot of small glued-in decorative parts, should be mostly obvious. There's a separate white part glued on the pot panel for better surface quality. I've colored the space under the letters with a black sharpie and then glued the labels on. The labels were printed with a 0.2 mm nozzle, not sure if you could resolve them with a 0.4 mm.

The joystick knob is 3d printed, with a silicone cover made for Switch 2.

Conclusion

Hope that this was useful or at least interesting. TERRIBLY SORRY for a lot of my design (in)decisions to anyone who might have decided to build this. Stay tuned for V2! Should be significantly friendlier to DIY.

Parts

19
QtyValueFootprintReferences
16R_PotentiometerPotentiometer_THT:Potentiometer_Alps_RK09K_Single_VerticalRV1, RV2, RV3, RV4, RV5, RV6, RV7, RV8, RV9, RV10, RV11, RV12, RV13, RV14, RV15, RV16
2MountingHole_2.2mm_M2_DIN965MountingHole:MountingHole_2.2mm_M2_DIN965 ,
1Conn_01x18_PinConnector_PinHeader_2.54mm:PinHeader_1x18_P2.54mm_VerticalJ1

Similar boards

  • 2 layers43.9 × 27.7 mmTcd1304-4v, the printed circuit board in 3D

    Tcd1304-4v

    OpnTec/open-spectrometer-hardware

    Open source VIS spectrometer

    19 parts1.5k
  • 2 layers50 × 60 mmDebate Device, the printed circuit board in 3D

    Debate Device

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    19 parts915
  • 2 layers102.9 × 96.7 mmISA adapter, the printed circuit board in 3D

    ISA adapter

    polpo/picogus

    Emulation of ISA sound cards and CD-ROM on Raspberry Pi Pico (GUS, SB/Adlib, MPU-401, Tandy, CMS, Panasonic CD-ROM) with USB mouse/joystick support

    19 parts805
  • 2 layers60 × 39 mmPs2usb, the printed circuit board in 3D

    Ps2usb

    rasteri/HIDman

    Adapting USB devices to work on old computers

    19 parts432
  • 2 layers70.1 × 43.2 mmIaq device, the printed circuit board in 3D

    Iaq device

    nkitanov/iaq_board

    IAQ Board is a DIY (Do-It-Yourself) device for measuring internal air quality

    19 parts396
  • 2 layers80 × 80 mmGB BRK CPU G1, the printed circuit board in 3D

    GB BRK CPU G1

    Gekkio/gb-hardware

    Game Boy -related custom hardware by gekkio

    19 parts379CC-BY-4.0
  • 2 layers25.4 × 25.4 mmIna169, the printed circuit board in 3D

    Ina169

    Ardumower/ardumower

    Develop an open source robotic lawn mower (HW+SW reference platform)

    19 parts282
  • 2 layers58.4 × 28.6 mmNew rele, the printed circuit board in 3D

    New rele

    zmaker/arduino_cookbook

    gli sketch del nuovo progetto Arduino Cookbook e dei video di YouTube

    19 parts269

Questions

How big is the Synth PCB?

It measures 261 × 18 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Synth use?

19 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Synth KiCad files?

From the povle/spark-synth-hardware repository on GitHub, at the commit this page was made from: the board is pot_pcb/synth.kicad_pcb and its schematic pot_pcb/synth.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Synth design in my own project?

Its repository states no licence, so its author keeps all rights: ask povle before reusing the design.