Skip to the content
2 layersTransmitter, the printed circuit board in 3D

This is a transponder intended for indoor microdrones. It's not that bright, which is fine when flying only a few feet from the receiver. It's also very small, which is good when every milligram counts.

Copper layers
2
Thickness
1.6 mm
Parts
6
Nets
9
Pads
23
Tracks, vias
48, 1
Pours
2
Routed
Yes
KiCad
KiCad 4
Created
2 Nov 2015
Updated
23 Jan 2023

Overview

Transmitter is an open-source printed circuit board by polyvision, from the polyvision/EasyRaceLapTimer repository on GitHub. It is a 2-layer board with 6 parts on 9 nets, routed with 48 tracks and 1 via.

Its parts include 2 resistors, 1 IC, 1 diode, 1 transistor and 1 connector. It belongs with the AVR (ATmega, ATtiny) boards of this library.

README

datasheets/micro_transponder_v1/README.md

This is a transponder intended for indoor microdrones. It's not that bright, which is fine when flying only a few feet from the receiver. It's also very small, which is good when every milligram counts.

It can still be programmed using alligator clips on the sides. The lettering on the back will show you which pad goes where (PB0, PB1, etc.). See the ATtiny85 datasheet for how they connect to the physical pins and their extended features.

Solder the +5V and GND pads to the power. If necessary, a +3.7V input (such as from a 1S lipo cell) should be enough.

Parts

6
QtyValueFootprintReferences
1330Resistors_ThroughHole:Resistor_Horizontal_RM7mmR1
139Resistors_ThroughHole:Resistor_Horizontal_RM7mmR2
1ATTINY85-PHousings_DIP:DIP-8_W7.62mmIC1
1AVR-ISP-6Pin_Headers:Pin_Header_Straight_2x03CON1
1IR LEDPin_Headers:Pin_Header_Straight_1x02D1
1Q_NPN_EBCTO_SOT_Packages_THT:TO-92_Inline_Narrow_OvalQ1

More from polyvision/EasyRaceLapTimer

1
  • 2 layers10.4 × 13 mmMicro transponder, the printed circuit board in 3D

    Micro transponder

    polyvision/EasyRaceLapTimer

    This is a transponder intended for indoor microdrones. It's not that bright, which is fine when flying only a few feet from the receiver. It's also very small, which is good when every milligram counts.

    11 parts103

Similar boards

  • 2 layers18.5 × 11.1 mmSwitch, the printed circuit board in 3D

    Switch

    byrantech/laptop

    anyon_e, a highly integrated, high end, open source laptop. Attempt the impossible.

    6 parts4.3kMIT
  • 2 layers14.6 × 33 mmBrain board SD Card 1, the printed circuit board in 3D

    Brain board SD Card 1

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    6 parts1.2k
  • 2 layers9 × 9 mmDpoint, the printed circuit board in 3D

    Dpoint

    Jcparkyn/dpoint

    Open-source digital stylus using camera tracking and inertial measurements

    6 parts1.1kMIT
  • 2 layers51.5 × 16.6 mmMicroswitchXY Endstop, the printed circuit board in 3D

    MicroswitchXY Endstop

    VoronDesign/Voron-Hardware

    Cool Hardware designed by the Voron Design group

    6 parts1.1kGPL-3.0
  • 2 layers21.9 × 76.7 mmAmiga External, the printed circuit board in 3D

    Amiga External

    hoglet67/RGBtoHDMI

    Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

    6 parts1kGPL-3.0
  • 2 layers88.9 × 50.8 mmBusinesscard, the printed circuit board in 3D

    Businesscard

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    6 parts915
  • 2 layers20.3 × 15.2 mmL0 RGB led, the printed circuit board in 3D

    L0 RGB led

    Luos-io/luos_engine

    Open-source and real-time orchestrator for cyber-physical-systems, to easily design, test and deploy embedded applications and digital twins.

    6 parts546MIT
  • 2 layers9 × 3.6 mmOpticalEncoder, the printed circuit board in 3D

    OpticalEncoder

    adamb314/ServoProject

    Getting the most out of your hobby servo

    6 parts545

Questions

What parts does the Transmitter use?

6 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Transmitter KiCad files?

From the polyvision/EasyRaceLapTimer repository on GitHub, at the commit this page was made from: the board is datasheets/transmitter/transmitter.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Transmitter design in my own project?

Its repository states no licence, so its author keeps all rights: ask polyvision before reusing the design.