Skip to the content
2 layers56 × 40 mmUSB to RS232-INTERFACE, the printed circuit board in 3D

USB to RS232-INTERFACE

pitiee-9/USB-to-RS232-INTERFACE

A kicad small PCB project, consists of gerber files of the pcb board structure of USB-RS232

Size
56 × 40 mm
Copper layers
2
Thickness
1.6 mm
Parts
14
Nets
26
Pads
73
Tracks, vias
127, 2
Pours
1
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
25 Aug 2026
Updated
25 Aug 2026

Overview

USB to RS232-INTERFACE is an open-source printed circuit board by pitiee-9, from the pitiee-9/USB-to-RS232-INTERFACE repository on GitHub. It is a 2-layer board of 56 × 40 mm with 14 parts on 26 nets, routed with 127 tracks and 2 vias.

It is built around the MAX232N and CH341T. Its parts include 9 capacitors, 2 ICs, 2 connectors and 1 crystal. It belongs with the interfaces and adapters boards of this library.

Main components

2

README

readme.md

USB to RS232 Interface

A KiCad hardware design for connecting a computer's USB port to a standard RS-232 serial device.

Overview

The board combines:

  • CH341T (U2) for USB-to-UART conversion
  • MAX232 (U1) for UART-to-RS-232 level conversion
  • A USB Type-A receptacle (J2) for the host connection
  • A DE-9/DB9 socket (J1) for the RS-232 connection
  • A 12 MHz SMD crystal (X1) for the CH341T clock

The signal path is:

text
USB host -> USB D+/D- -> CH341T UART -> MAX232 -> DE-9 RS-232 connector

The MAX232 charge-pump capacitors are routed to the converter's C1+, C1-, C2+, C2-, V+, and V- pins. The board also routes USB VBUS and ground between the USB interface and the serial circuitry.

Design status

This repository contains a Version 1 schematic and PCB layout created with KiCad 9.0. The PCB title block identifies the project as USB TO RS232 INTERFACE and the board outline is a 56 mm x 40 mm rectangle.

Before assembly or connection to equipment, verify the exact component variants, supply voltage requirements, connector pin mapping, and RS-232 cable wiring against the relevant datasheets and the target equipment.

Main components

ReferencePart / valueFootprint or package
U1MAX232SOIC-16, 3.9 x 9.9 mm, 1.27 mm pitch
U2CH341TSSOP-20, 5.3 x 7.2 mm, 0.65 mm pitch
X112 MHz crystalSMD 5032, 2-pin
J2USBUSB-A Molex 67643, horizontal
J1DB9DE-9 socket, horizontal, through-hole style
C34700 pF1206 metric
C40.1 uF1206 metric
C2, C9See schematicValues are not populated in the exported BOM

The authoritative component values and connections are the KiCad schematic and the supplied BOM. The exported BOM currently contains incomplete value fields for C2 and C9; resolve those before ordering parts.

Repository contents

KiCad design files

  • USB TO RS232 INTERFACE.kicad_pro: KiCad project settings
  • USB TO RS232 INTERFACE.kicad_sch: source schematic
  • USB TO RS232 INTERFACE.kicad_pcb: source PCB layout
  • USB TO RS232 INTERFACE.kicad_sch-bak: schematic backup
  • USB TO RS232 INTERFACE-backups/: KiCad backup files
  • _autosave-USB TO RS232 INTERFACE-backups/: autosaved project backups

Manufacturing outputs

  • Gerber files/: copper, edge cuts, solder-mask-related fabrication data, drill files, and the Gerber job file
  • Pick and place files/: top and bottom component placement CSV files
  • Bills of material/USB TO RS232 INTERFACE.csv: exported bill of materials
  • DXF files/: board and layer drawing exports

For fabrication, use the Gerber job file together with the Gerbers and drill files. For assembly, use the BOM alongside the appropriate pick-and-place file and confirm orientation in the PCB editor.

Recommended workflow

  1. Open USB TO RS232 INTERFACE.kicad_pro in KiCad 9.0 or a compatible newer version.
  2. Review the schematic and assign or confirm the missing capacitor values.
  3. Run electrical-rule checking and resolve any intentional warnings.
  4. Run PCB design-rule checking and confirm the board outline on Edge.Cuts.
  5. Regenerate the BOM, Gerbers, drill files, and pick-and-place files after any design change.
  6. Assemble the PCB, inspecting the pin-1/orientation marks for U1, U2, the crystal, capacitors, and connectors.
  7. Test USB enumeration and serial communication with current CH341 drivers and a known-good RS-232 device.

Bring-up checklist

  • Inspect the PCB for shorts, solder bridges, and incorrect component orientation.
  • Confirm continuity of USB ground and VBUS before applying power.
  • Confirm the selected MAX232 part is compatible with the board supply and capacitor network.
  • Connect the USB cable and check whether the CH341 serial device appears on the host.
  • Use a terminal program with the intended serial settings and perform a loopback or known-good-device test.
  • Measure the RS-232 output levels before connecting sensitive external equipment.

Notes and limitations

  • The design exposes a DE-9 connector, but RS-232 device pin assignments and cable gender are application-dependent. Check the target device documentation.
  • USB driver behavior depends on the host operating system and the exact CH341 variant.
  • The repository does not define a single baud rate, flow-control mode, or complete external connector pinout in this README; these should be documented once the intended application is fixed.
  • Do not connect the RS-232 connector directly to a logic-level UART without the MAX232 stage.

License

No license is currently specified for this project. Add a license file and update this section before redistributing the design.

Parts

14
QtyValueFootprintReferences
50.47uFCapacitor_SMD:C_1206_3216MetricC5, C6, C7, C8, C9
220pFCapacitor_SMD:C_1206_3216MetricC1, C2
10.1uFCapacitor_SMD:C_1206_3216MetricC4
112MHzCrystal:Crystal_SMD_5032-2Pin_5.0x3.2mm_HandSolderingX1
14700pFCapacitor_SMD:C_1206_3216MetricC3
1CH341TPackage_SO:SSOP-20_5.3x7.2mm_P0.65mmU2
1DB9Connector_Dsub:DSUB-9_Socket_Horizontal_P2.77x2.84mm_EdgePinOffset4.94mm_Housed_MountingHolesOffset4.94mmJ1
1MAX232Package_SO:SOIC-16_3.9x9.9mm_P1.27mmU1
1USBConnector_USB:USB_A_Molex_67643_HorizontalJ2

Similar boards

  • 2 layers100 × 70 mmRTD2662Board, the printed circuit board in 3D

    RTD2662Board

    KerJoe/RTD2662Board

    Prototype board for RTD2662 display controller

    259 parts24
  • 2 layers40 × 55 mmPs2usb, the printed circuit board in 3D

    Ps2usb

    rasteri/HIDman

    Adapting USB devices to work on old computers

    26 parts432
  • 2 layers132.1 × 45.7 mmIPoS, the printed circuit board in 3D

    IPoS

    peterheinrich/InternetOverSpaghetti

    Transmitting IP packages over a pair of spaghetti thus demonstrating how media independent IP really is.

    42 parts342
  • 2 layers60.5 × 31.5 mmPs2-serial mouse adapter, the printed circuit board in 3D

    Ps2-serial mouse adapter

    necroware/ps2-serial-mouse-adapter

    PS/2 to serial port mouse adapter

    13 parts89GPL-3.0
  • 2 layers79.7 × 35.1 mmUSB-2-232, the printed circuit board in 3D

    USB-2-232

    LimeProgramming/USB-serial-mouse-adapter

    Convert USB mouse to Serial mouse using Pi Pico

    29 parts50MPL-2.0
  • 2 layers148.3 × 116.6 mmKiCAD RetroArduInput, the printed circuit board in 3D

    KiCAD RetroArduInput

    RetroFuturisticEngineer/RetroARDUInput

    Use USB Keyboards, Mice and Joysticks on PC/XT, PC/AT, Tandy 1000, Atari, Amiga, C64 and Apple

    48 parts25LGPL-2.1
  • 2 layers99.1 × 99.1 mm6809v2, the printed circuit board in 3D

    6809v2

    jbevren/6809v2

    Code and design repository for the 6809v2 SBC: To be released at VCFMW 13

    60 parts22
  • 2 layers100 × 45 mmTranscribe, the printed circuit board in 3D

    Transcribe

    cyberboy666/_transcribe_

    midi to rs232 bridge - for performance control of old video mixers and switchers

    28 parts20

Questions

How big is the USB to RS232-INTERFACE PCB?

It measures 56 × 40 mm and has 2 copper layers, 1.6 mm thick.

What parts does the USB to RS232-INTERFACE use?

14 parts, built around the MAX232N and CH341T. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the USB to RS232-INTERFACE KiCad files?

From the pitiee-9/USB-to-RS232-INTERFACE repository on GitHub, at the commit this page was made from: the board is USB TO RS232 INTERFACE.kicad_pcb and its schematic USB TO RS232 INTERFACE.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the USB to RS232-INTERFACE design in my own project?

Its repository states no licence, so its author keeps all rights: ask pitiee-9 before reusing the design.