Skip to the content
2 layers78.2 × 16 mmMenuPanel, the printed circuit board in 3D

A redux of @TheTrain24's Project Purple in my own flavor.

Size
78.2 × 16 mm
Copper layers
2
Thickness
2.53 mm
Parts
13
Nets
13
Pads
43
Tracks, vias
52, 0
Pours
1
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
29 Sep 2024
Updated
24 Nov 2024

Overview

MenuPanel is an open-source printed circuit board by phazil, from the phazil/Purple-Project-Redux repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 78.2 × 16 mm with 13 parts on 13 nets, routed with 52 tracks and 0 vias.

Its parts include 6 resistors, 6 switches and 1 connector.

README

README.md

Purple Project Redux

A recreation of @TheTrain24's Purple Project seen here: Reference Posts

This started out as a post graduation project (someone in biology hire me pls) to explore deeper into the hobbies I was already interested in. Did all of the CAD/KiCAD work myself, and also because I missed out on the originals Train posted. Lots was learned here, and documenting it all isn't as fun as making it but I guess it's necessary lol.

This is my attempt to recreate Train's version, however there are differences. There is no custom wiring terminal pcb, it's not double stacked FR4 for both front/back panel, and there's no usage of low profile OSBMXs. I used a right angle header soldered onto a Basic Breakout Board running GP2040-CE along with a 20-pin wiring harness. There is some soldering involved in this to get the menu panel working however it is sequential and there's only 1 ground line needed. The single panel do not flex at all with the increase inside area of the 3D prints. you would have to try to push down really hard on the center of the panels to even see any sort of flex. Any low profile buttons that fit within a 20mm tall enclosure should work too.

As regards for making and selling, I do not think this is the most efficient way to go about it. The original project I am pretty sure was scrapped due to how expensive FR4 panels end up being. Using laser cut acrylic is probably more efficient for anything of the sorts. Total cost for making 5 of these is about $750 with the materials I chose, so around $160 each is close to breaking even. This does not at all account for the time needed to print parts or build this.

If you need any help or are even thinking about making this please contact me on Discord! I'd be willing to help. @phazil

Showcase Test Showcase Test 2

Repository Directory:

Features, Details, and To-Dos

3 Variations:

  • Purple Project Redux: 35.56cm x 20.32cm x 2.32cm (14" x 8" x 0.9")
  • UNTESTED Acrylic Layer Version: 35.56cm x 20.32cm x 2.47cm (14" x 8" x 0.97")
  • Right side carrying handle modifcation available for both (Adds about 1.25" to total length)

Features:

  • Daigo-ish Layout
  • Stickless+
  • Bottom Rubber Pads
    • Mirrored for both sides
  • Right side carrying handle
  • PCB top/bottom plate (1.6mm)
  • Possible Acrylic Top Plate (3.1mm total thickness, only screw ins work)
  • Designed PCB Auxilliary Button Panel

Each designed part can fit in a 250x250x250 volume print bed

  • 6 total pieces
    • Top Left
    • Top Right
    • Top Middle (Requires USB-C keystone jack panel mount)
    • Bottom Left
    • Bottom Middle
    • Bottom Right
  • Printed in Voron Spec hopefully

To Do's:

  • BOM Page written
  • Ordering Page written
  • Printing Parts written
  • Rough Assembly Guide written
  • Editting Parts written
  • Bottom Rubber/Foam pad DXFs

Parts

13
QtyValueFootprintReferences
60Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR1, R2, R3, R4, R5, R6
6SW_PushButton_Switch_THT:SW_PUSH_6mm_H4.3mmSW1, SW2, SW3, SW4, SW5, SW6
1Conn_01x07_SocketConnector_PinSocket_2.54mm:PinSocket_1x07_P2.54mm_VerticalJ1

Similar boards

  • 2 layers40 × 20 mmUsb uart, the printed circuit board in 3D

    Usb uart

    earthtojake/text-to-cad

    Design physical products with AI

    13 parts26kMIT
  • 2 layers35 × 29 mmMagSpoofTC, the printed circuit board in 3D

    MagSpoofTC

    samyk/magspoof

    A portable device that can spoof/emulate any magnetic stripe, credit card or hotel card "wirelessly", even on standard magstripe (non-NFC/RFID) readers.

    13 parts4.2k
  • 2 layers20.6 × 23.6 mmAO-03 signal amplifier, the printed circuit board in 3D

    AO-03 signal amplifier

    fossasia/pslab-scripts

    Pocket Science Lab - Scripts for Sensor Experiments

    13 parts1.6kApache-2.0
  • 2 layers47 × 35.6 mmMX7-C-35PL C11, the printed circuit board in 3D

    MX7-C-35PL C11

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    13 parts1.2k
  • 2 layers95 × 95 mmCube batteryboard, the printed circuit board in 3D

    Cube batteryboard

    willem-pennings/balancing-cube

    A cube that balances itself in a corner or edge using reaction wheels

    13 parts1.1kGPL-3.0
  • 2 layers15.2 × 20.3 mmPt100stick, the printed circuit board in 3D

    Pt100stick

    VoronDesign/Voron-Hardware

    Cool Hardware designed by the Voron Design group

    13 parts1.1kGPL-3.0
  • 2 layers53.9 × 23.2 mmBuffer, the printed circuit board in 3D

    Buffer

    hoglet67/RGBtoHDMI

    Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

    13 parts1kGPL-3.0

Questions

How big is the MenuPanel PCB?

It measures 78.2 × 16 mm and has 2 copper layers, 2.53 mm thick.

What parts does the MenuPanel use?

13 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the MenuPanel KiCad files?

From the phazil/Purple-Project-Redux repository on GitHub, at the commit this page was made from: the board is Source Files/KiCAD Files/MenuPanel/MenuPanel.kicad_pcb and its schematic Source Files/KiCAD Files/BackPanel/BackPanel.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the MenuPanel design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).