Skip to the content
2 layers52.8 × 45.1 mmBadge, the printed circuit board in 3D

Hardware and Firmware for the OzLockCon2017 Badge

Size
52.8 × 45.1 mm
Copper layers
2
Thickness
1.6 mm
Parts
14
Nets
10
Pads
40
Tracks, vias
172, 6
Pours
3
Routed
Yes
KiCad
KiCad 4
Created
4 Jun 2017
Updated
6 Jun 2017

Overview

Badge is an open-source printed circuit board by peterfillmore, from the peterfillmore/OzLockConBadge2017 repository on GitHub, published under the Unlicense licence. It is a 2-layer board of 52.8 × 45.1 mm with 14 parts on 10 nets, routed with 172 tracks and 6 vias.

Its parts include 4 resistors, 4 diodes, 1 capacitor, 1 IC and 1 connector. It belongs with the lEDs and displays boards and the AVR (ATmega, ATtiny) boards of this library.

README

README.md

OzLockConBadge2017

Hardware and Firmware for the OzLockCon2017 Badge

Derived from the uDuck: https://github.com/insecurityofthings/uDuck - as you can probably tell from the source code.

The hardware may support the uDuck firmware as the circuit is based off it - but i screwed something up and it doesn't want to work. Ran out of time to debug so focused on the flashy flashy.

Warning!

don't solder the USB connector onto the badge until you check the pin out! i screwed up and reversed the pads on the footprint - again...

Parts

14
QtyValueFootprintReferences
268Resistors_SMD:R_0805_HandSolderingR2, R3
2LEDOzLockCon:LED_3528D1, D2
2ZENERDiodes_SMD:D_SOD-323_HandSolderingD3, D4
1OzLockCon:OzLockConLogo
10.1uFCapacitors_SMD:C_0805_HandSolderingC1
11.5kResistors_SMD:R_0805_HandSolderingR1
110kResistors_SMD:R_0805_HandSolderingR4
1ATTINY85-SSMD_Packages:SOIC-8-NIC1
1BatteryOzLockCon:CR2032_SMDBT1
1SW_PUSHButtons_Switches_SMD:SW_SPST_PTS645SW1
1USB_AOzLockCon:USB_A_SMDP1

Similar boards

  • 2 layers116.8 × 30 mmType d, the printed circuit board in 3D

    Type d

    google/mozc-devices

    Circuit diagrams and firmware source code for Gboard DIY keyboards

    14 parts3kApache-2.0
  • 2 layers32 × 22 mmDiff driver, the printed circuit board in 3D

    Diff driver

    rene-dev/stmbl

    AC Servo Driver for STM32F4

    14 parts990GPL-3.0
  • 2 layers34 × 45 mm2032Charger, the printed circuit board in 3D

    2032Charger

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    14 parts915
  • 2 layers34 × 109.9 mmTdisplay s3, the printed circuit board in 3D

    Tdisplay s3

    landonr/homeThing

    Wifi Smart Home Remotes that run on ESPHome

    14 parts551GPL-3.0
  • 2 layers45.3 × 42.7 mmMainPcb, the printed circuit board in 3D

    MainPcb

    adamb314/ServoProject

    Getting the most out of your hobby servo

    14 parts545
  • 2 layers42.5 × 28.8 mmC5VRX JACK DIY, the printed circuit board in 3D

    C5VRX JACK DIY

    Twotoz/C5VRX

    Ultra-minimal, zero-CPU 5.8 GHz analog FPV video receiver using ESP32-C5 Wi-Fi 6 PHY MODEM_DIAG, BitScrambler WBFM demodulation & resistor DAC CVBS

    14 parts515GPL-3.0
  • 2 layers62 × 24 mmMai button, the printed circuit board in 3D

    Mai button

    whowechina/mai_pico

    Pico controller for Maimai

    14 parts475

Questions

How big is the Badge PCB?

It measures 52.8 × 45.1 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Badge use?

14 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Badge KiCad files?

From the peterfillmore/OzLockConBadge2017 repository on GitHub, at the commit this page was made from: the board is hardware/Badge.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Badge design in my own project?

Its repository publishes it under the Unlicense licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).