Skip to the content
2 layers80 × 34.5 mmBc250 carrier, the printed circuit board in 3D

A small controller + receiver (esp32) for controlling a string of ws2812b leds. It installs a daemon that can switch between different effects based on some defined rules.

Size
80 × 34.5 mm
Copper layers
2
Thickness
1.6 mm
Parts
16
Nets
18
Pads
77
Tracks, vias
120, 48
Pours
3
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
10 Jun 2026
Updated
3 Nov 2026

Overview

Bc250 carrier is an open-source printed circuit board by peterdk31, from the peterdk31/bc250_ws2812b_controller repository on GitHub. It is a 2-layer board of 80 × 34.5 mm with 16 parts on 18 nets, routed with 120 tracks and 48 vias.

Its parts include 11 connectors, 1 resistor and 1 transistor.

README

hardware/bc250_carrier_e/README.md

BC-250 carrier board (rev E)

Rev E is the same carrier as rev D, with the same parts, nets and firmware, laid out differently: every plug sits on the left, the PSU header at the board's right-hand end, and the module directly beside it. The fans run down the left edge, the breakouts, the button and the strip sit in a column beside them, and no signal has to cross the PSU plug's zone. 76.8 × 34.5 mm (rev D: 80 × 34.5), two layers.

Annotated pinout of rev E: every pad labelled with its rail, GPIO and role

make pinout → pinout.png, drawn from generate.py's geometry. Open it at full size for soldering.

Both revisions stay buildable side by side: rev D in hardware/bc250_carrier/, rev E here. The tools (check.py, drc.py, fill.py, preview.py, fab.py, zoom.py) are copies of rev D's and work the same way; only generate.py and pinout.py differ.

Layout

Left to right:

  • The four fan headers stacked down the left edge, 9 mm apart, pins G · 12V · T · PWM left to right, lock ramps facing down. Their 12 V and GND are two bars down the column.
  • Column C, top to bottom: the power breakout J14, the button J9, R1, Q1 and the strip VH (J3). The fan PWM lines cross it in three lanes between J14 and J9 (FAN4's between Q1 and the VH).
  • J11 (the sense wire and the spare GPIOs), right beside the module's left pad column.
  • The Super Mini in its two sockets (J12, J13), USB-C at the top edge. Nothing sits under it, so it can still be soldered flat instead of socketed.
  • The PSU header (J1) directly beside the module at the right-hand end, the same right-angle Mini-Fit Jr as rev D, facing the same way: the plug lies flat over the board's right quarter and its wires leave over the top edge. Everything above the header is the plug zone: tracks only, nothing taller than the solder mask.

The module's right pads (DIN, GATE, BTN, GPIO0) face the PSU header, so their lines go round the module: down the gap between it and the header (6.7 mm between their pin columns) (or inside its right pad column) and west along the bottom edge under its antenna end, next to the strip's 3 A feed from the header's 3.3V pin.

No mounting holes: the plug zone has to stay flat and every other spot is taken. The repo's case isn't used with this board.

What is on it

The same parts as rev D (see its ordering table; J11 and J14 are still cut from 2 × 8 pin headers and left off assembly orders).

The rev C fan headers (Ckmtw W-2510S04P, KF2510) fit the same holes, but only just: their body is 12.7 mm long (the Molex's about 10.2), so FAN2's reaches about 0.2 mm into J9's housing and FAN3's and FAN4's about 0.15 mm into J3's. Dry-fit first: fit J9 and J3, then push each fan header towards the left edge while soldering it (the pins have about 0.15 mm of play in their holes); if one still won't sit flat, file about 0.3 mm off the end facing column C. Their lock ramp spans all four pins, so it needs cutting down as on rev C; fit them with the ramp facing down the board, as the silkscreen shows. A fan plug as long as 12.7 mm would just touch J9 or J3 when plugged in (not checked on a real plug).

refpartwhere
J5–J8four Molex 47053-1000 fan headers, stacked, pins G 12V T PWM left to rightleft edge
J142 × 3 power breakout, turned: three columns 3V3, 12V, 5VSB, two pins eachcolumn C, top
J9JST-XH 4-pin button connector: pins 12V, GND, NO, C left to rightcolumn C
R1, Q1100 kΩ; 2N7000 on the wide TO-92 footprint (S G D left to right)column C
J3JST-VH strip connector, turned 180: GND, DIN, 3.3V left to rightcolumn C, bottom
J112 × 6: SENSE + five spare GPIOs, GND beside each (as rev D)between column C and the module
U1 on J12 + J13ESP32-C3 Super Mini in two 1 × 8 low-profile socketsbeside the PSU header
J1PSU header, Mini-Fit Jr 5569-10A2 right-angleright-hand end

Wiring

connectorpinsgoes to
PSU J1as rev D (the PSU header)the FSP500-30AS 10-pin plug, straight on
STRIP J31 3.3V, 2 DIN, 3 GND; pin 1 is the right pinthe WS2812B strip; DIN is GPIO4
BUTTON J91 12V, 2 GND, 3 NO, 4 C; pin 1 is the left pinthe illuminated button as on rev D: 1–2 the ring LED (12 V), 3 the normally-open contact → GPIO1, 4 the switch's common (a real GND)
J111 GND / 2 SENSE, 3 / 4 GPIO8, 5 / 6 GPIO9, 7 / 8 GPIO20, 9 / 10 GPIO21, 11 / 12 GPIO0 (odd pins GND)as rev D: the sense wire (BC-250 TPMS1 pin 9) on pin 2; OpenPuck 017 → pin 8, its GND → pin 7
J14columns left to right: pins 1+2 3.3V, 3+4 12V, 5+6 5VSBoptional rail breakout; an OpenPuck's BAT goes on 5VSB (pin 5 or 6)
FAN1 J5 … FAN4 J8left to right: G, 12V, T, PWMstandard 4-pin fans, tach unconnected; FAN1..4 = GPIO 5, 6, 7, 10 = header1..4 in the config, top to bottom. The lock ramps face down the board

The config is unchanged from rev D: the same power_switch pins, the same fan headers, strip.pin 4.

Routing

The rule from rev D holds: on the back, where every joint is soldered, 12 V passes no pad of 5VSB, GATE, 3.3V, PS_ON# or any GPIO within 1 mm. The only 12 V on the back is the PSU header's own pin 4-5 tie (J14's pins sit 0.84 mm apart at the 2.54 mm pitch, as on any header). A slipped bridge on the back can short a rail to ground or switch the PSU, never feed 12 V into the module. On the front, under FAN1's plastic, the top-edge 12 V passes FAN1's PWM pin at 0.6 mm.

  • 12 V leaves the PSU header's pin 4 straight up through the plug zone and runs along the top edge on the front (2 mm, ~3.5 A), then down the fans' 12V pins as a bar. J14's 12 V column taps it, and J9's LED is fed from that column on the front.
  • The fans' ground runs along the top edge on the back, right under the 12 V, and down the fans' G pins, so the fan current's loop is one narrow strip. At the other end it drops into the PSU header's pin 2. A ground spine runs down the back of the gap between the module and the header, from the top edge to the bottom edge; the module's GND pad joins it, a branch goes over pin 1 into pin 2, and the strip's 3 A return comes east along the bottom edge from the VH's GND pin into it. J9's, J11's, Q1's and R1's grounds have a web of their own down column C into the VH's GND pin, and the ground fill on both layers, stitched with ground vias, ties in everything else.
  • 3.3V (3 A) leaves the header's pin 6 as a 2.5 mm track west along the bottom edge on the front, into the VH's pin 1. On from there, narrower, it runs under the VH's other pins to the gap by the fans and up it into J14's 3V3 column.
  • 5VSB runs from the header's pin 3 up through the plug zone into the module's 5V pin (front), and on over the module's top to J14's 5VSB column.
  • The fan PWM lines run west on the back: FAN1's to FAN3's off the module's top three pads, in three lanes under J14 to the gap by the fans, then up or down into each pin 4. FAN4's goes down between J11 and the module, under J11 and over the VH's pins.
  • DIN goes down the back inside the module's right pad column (0.5 mm from the pads, clear of the antenna zone), west along the bottom and up into the VH's pin 2. SENSE goes up the same lane on the front and over the module's top into J11. GPIO0 drops off its pad and goes west under the module's end into J11's bottom row.
  • BTN and GATE go east off their pads, down the gap by the header, west along the bottom edge and up between column C and J11: BTN under J9 into its pin 3, GATE into R1's pin 1 and on to Q1's gate. PS_ON# leaves the PSU header's pin 8 through the gap between its pin rows on the back, changes to the front through a via just past the header's left end and follows them into Q1's drain.

Clearances as rev D: 0.5 mm from any solder pad to copper of another net, 0.3 mm track to track, 0.5 mm fill clearance; check.py and KiCad's DRC are both clean.

Building, checking, ordering

As rev D: building it, before the first power-up (the PSU header's pins are numbered the same; on rev E Q1's middle hole is still the gate), ordering (make writes out/fab/ here too) and flashing. Q1's legs are printed S G D on rev E (left to right), the opposite way round from rev D's D G S: follow the silkscreen outline.

make regenerates the KiCad files (bc250_carrier_e.*), fills and stitches the ground, runs check.py and KiCad's DRC, renders out/preview.png (plus preview-F.png / preview-B.png, one layer each) and pinout.png, and exports gerbers, PDFs and the fab folders into out/.

Parts

16
QtyValueFootprintReferences
3M3MountingHole:MountingHole_3.2mm_M3H2, H3, H4
1100kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR1
12N7000Package_TO_SOT_THT:TO-92_Inline_WideQ1
1BUTTONConnector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_VerticalJ9
1FAN1 GPIO5Connector_Molex:Molex_KK-254_AE-6410-04A_1x04_P2.54mm_VerticalJ5
1FAN2 GPIO6Connector_Molex:Molex_KK-254_AE-6410-04A_1x04_P2.54mm_VerticalJ6
1FAN3 GPIO7Connector_Molex:Molex_KK-254_AE-6410-04A_1x04_P2.54mm_VerticalJ7
1FAN4 GPIO10Connector_Molex:Molex_KK-254_AE-6410-04A_1x04_P2.54mm_VerticalJ8
1PSU Mini-Fit Jr 2x5 R/AConnector_Molex:Molex_Mini-Fit_Jr_5569-10A2_2x05_P4.20mm_HorizontalJ1
1PWR 3.3V/5VSB/12V (optional)Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_VerticalJ14
1SENSE+GPIO/GNDConnector_PinHeader_2.54mm:PinHeader_2x06_P2.54mm_VerticalJ11
1STRIPConnector_JST:JST_VH_B3P-VH_1x03_P3.96mm_VerticalJ3
1U1 socket LConnector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_VerticalJ12
1U1 socket RConnector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_VerticalJ13

More from peterdk31/bc250_ws2812b_controller

1
  • 2 layers76.8 × 34.5 mmBc250 carrier e, the printed circuit board in 3D

    Bc250 carrier e

    peterdk31/bc250_ws2812b_controller

    A small controller + receiver (esp32) for controlling a string of ws2812b leds. It installs a daemon that can switch between different effects based on some defined rules.

    13 parts4

Similar boards

  • 2 layers140.5 × 30 mmType e, the printed circuit board in 3D

    Type e

    google/mozc-devices

    Circuit diagrams and firmware source code for Gboard DIY keyboards

    16 parts3kApache-2.0
  • 2 layers41.4 × 14.5 mmU2f zero, the printed circuit board in 3D

    U2f zero

    conorpp/u2f-zero

    U2F USB token optimized for physical security, affordability, and style

    16 parts2.4k
  • 2 layers122 × 37 mmV0-UmbilicalBoard, the printed circuit board in 3D

    V0-UmbilicalBoard

    VoronDesign/Voron-Hardware

    Cool Hardware designed by the Voron Design group

    16 parts1.1kGPL-3.0
  • 2 layers152 × 57.6 mmVideoslotadapter, the printed circuit board in 3D

    Videoslotadapter

    hoglet67/RGBtoHDMI

    Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

    16 parts1kGPL-3.0
  • 2 layers36 × 63.4 mmSmart ringfinal layout, the printed circuit board in 3D

    Smart ringfinal layout

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    16 parts915
  • 2 layers60 × 40 mmHASwitchPlate, the printed circuit board in 3D

    HASwitchPlate

    aderusha/HASwitchPlate

    LCD touchscreen for Home Automation

    16 parts738MIT
  • 2 layers21.1 × 26.9 mmDemo, the printed circuit board in 3D

    Demo

    easyw/kicadStepUpMod

    kicadStepUp: ECAD to MCAD FreeCAD WorkBench

    16 parts704

Questions

How big is the Bc250 carrier PCB?

It measures 80 × 34.5 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Bc250 carrier use?

16 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Bc250 carrier KiCad files?

From the peterdk31/bc250_ws2812b_controller repository on GitHub, at the commit this page was made from: the board is hardware/bc250_carrier/bc250_carrier.kicad_pcb and its schematic hardware/bc250_carrier/bc250_carrier.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Bc250 carrier design in my own project?

Its repository states no licence, so its author keeps all rights: ask peterdk31 before reusing the design.