Skip to the content
2 layersDTX-01 Controller, the printed circuit board in 3D
Copper layers
2
Thickness
1.6 mm
Parts
20
Nets
110
Pads
199
Tracks, vias
50, 0
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
26 Aug 2026
Updated
27 Aug 2026

Overview

DTX-01 Controller is an open-source printed circuit board by Patrik-OM1EPT, from the Patrik-OM1EPT/DTX01-Experiments repository on GitHub, published under the MIT licence. It is a 2-layer board with 20 parts on 110 nets, routed with 50 tracks and 0 vias.

It is built around the ESP32-DEVKITC-VE, 74LS299DC and ULN2003A. Its parts include 8 ICs, 6 resistors, 3 transistors, 2 connectors and 1 capacitor. It belongs with the ESP32 boards of this library.

Main components

3

README

README.md

DTX01 FM Transmitter experiments

Co-Authored with Bruno.

About DTX-01

DTX-01 is a FM transmitter that we bought at an amateur radio hamfest and in Holice, Czech Republic. Part of the hamfest was also a giant flea market full of old radios, reel-to-reel tape recorders and basically every electronic device known to man. But our interest was quickly stolen by this fm radio transmitter for 50czk (around 2 dollars/euros). It was a part of a security or an alarm system that was operating in the 300MHz part of the radioband. This band was later given to the army and this transmitters were suddenly illegal, so they were decommissioned. Our goal is to make it operate at 70cm amateur radio band, and create a DMR transmitter from it.

Here is our current progress day by day:

Day 1:

We created a board prototype, to control the parallel bus of the transmitter's PLL chip from and esp32. We used three shift registers (sn74ls299n) and three darlington transistor arrays (uln2003a). We used the shift registers to expand the IO on our ESP32. We also added a three channel level shifter (which turned out to not work). I have used the wrong design for the job. It was made from three bss138 mosfets and two resistors. And finally we connected three ethernet cables to the radio board, which we will use to interface with the control board.

Day 2:

Today, we wrote some code for the ESP32 (which you can find in this repo), and debugging our work. Then, I connected the three ethernet cables up to the control board and, of course, it didn't work. I found out, that Bruno's pinout was different (in the code), than was I wired up... (oops). Then, Bruno had to go for the day, but I finished off by adding a 7805 regulator to our control board so it can be powered from the same 12V supply as the radio transmitter. ESP32 is regulating it's own 3.3V from the 5V rail we provide.

TO BE CONTINUED :)

Parts

20
QtyValueFootprintReferences
310KResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR2, R4, R6
31KResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR1, R3, R5
32N3904Package_TO_SOT_THT:TO-92_InlineQ1, Q2, Q3
374LS299Package_DIP:DIP-20_W7.62mm_Socket_LongPadsU1, U2, U3
3ULN2003APackage_DIP:DIP-16_W7.62mm_Socket_LongPadsU5, U6, U7
1440uF 20VCapacitor_THT:CP_Radial_D10.0mm_P5.00mmC1
1Conn_01x24Connector_PinSocket_2.54mm:PinSocket_1x24_P2.54mm_VerticalJ1
1ESP32-DevKitCEspressif:ESP32-DevKitCU4
1Jack-DCConnector_BarrelJack:BarrelJack_HorizontalJ2
1LM7805_TO220Package_TO_SOT_THT:TO-220-3_VerticalU8

Similar boards

  • 2 layers85.2 × 71.3 mmBootarooni, the printed circuit board in 3D

    Bootarooni

    phooky/bootarooni

    A Raspberry Pi Pico (RP2040) based Apple IIe expansion card with USB isolation.

    34 parts12
  • 2 layers137 × 101.1 mmZ80 board1, the printed circuit board in 3D

    Z80 board1

    alexfreed58/z80-CPM-board-with-smart-i-o

    This is yet another retro computer running CPM on an actual Z80 CPU with a twist. Instead of using a traditional UART for communications, it uses a RPi pico module that is no bigger and no more expensive than a UART.

    48 parts2MIT
  • 2 layers96.5 × 76.2 mmAntiMonitor, the printed circuit board in 3D

    AntiMonitor

    FoxCutter/Cubit

    Source code repo for the Cubit z80 computer project

    18 partsBSD-2-Clause
  • 2 layers235 × 160 mmInput output.Text, the printed circuit board in 3D

    Input output.Text

    lynchaj/duodyne

    Duodyne is a hobbyist retrocomputer system designed to run ROMWBW. It is comprised of modules on a system bus

    87 parts15
  • 2 layers100 × 100 mmDram test, the printed circuit board in 3D

    Dram test

    Edgeworth/memepu

    cmake -DUSEAFL=yes -DCMAKEBUILDTYPE=Release $PFX/verymeme AFLSKIPCPUFREQ=yes AFLPRELOAD=/usr/local/lib/afl/libdislocator.so \ afl-fuzz -m 1024M -i $PFX/verymeme/testdata/memelang/parsing -o memelangfuzz \ -x…

    52 parts9GPL-3.0
  • 2 layers71.4 × 53.3 mmArrington Eprom Programmer, the printed circuit board in 3D

    Arrington Eprom Programmer

    abzman/Exidy-Sorcerer-Stuff

    boards and maybe software for the exidy sorcerer

    19 parts5
  • 2 layers99.1 × 99.1 mmVT100, the printed circuit board in 3D

    VT100

    Roland-Scholz/FABIAN

    FAbulous BInary ANihilator

    34 parts1

Questions

What parts does the DTX-01 Controller use?

20 parts, built around the ESP32-DEVKITC-VE, 74LS299DC and ULN2003A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the DTX-01 Controller KiCad files?

From the Patrik-OM1EPT/DTX01-Experiments repository on GitHub, at the commit this page was made from: the board is DTX-01_Controller/DTX-01_Controller.kicad_pcb and its schematic DTX-01_Controller/DTX-01_Controller.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the DTX-01 Controller design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).