Skip to the content
2 layers85 × 84 mmADCS, the printed circuit board in 3D

Radio (communications) module for the 2U CubeSat, LoRa version, Rev A.

Size
85 × 84 mm
Copper layers
2
Thickness
1.6 mm
Parts
105
Nets
87
Pads
377
Tracks, vias
953, 95
Pours
2
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
17 Sep 2026
Updated
25 Oct 2026

Overview

ADCS is an open-source printed circuit board by PARTH-KAKIRDE, from the PARTH-KAKIRDE/CUBESAT repository on GitHub, published under the MIT licence. It is a 2-layer board of 85 × 84 mm with 105 parts on 87 nets, routed with 953 tracks and 95 vias.

Its parts include 36 capacitors, 20 resistors, 15 connectors and 10 ICs. It belongs with the STM32 boards of this library.

README

TTC/README.md

TTC — Telemetry, Tracking & Command

Radio (communications) module for the 2U CubeSat, LoRa version, Rev A.

Overview

An STM32F446RET6 (same MCU and footprint as ADCS) drives an RFM98W LoRa module (Semtech SX1278) at 435–438 MHz. It sends telemetry to the ground station (a LilyGO LoRa board running TinyGS), receives commands, and passes data to and from the OBC over I²C (same connector and pins as ADCS) or UART. Power comes from the EPS 3.3 V or 5 V rail (JST-XH, as on ADCS).

The antenna output is either an SMA connector (default) or an LC balun feeding a dipole; fit one of the 0 Ω links R18 or R19.

Status: schematic complete. PCB is 85 × 84 mm, 2-layer, fully routed (KiCad DRC: 0 violations, 0 unconnected, schematic parity clean). Outline and four 4 mm mounting holes (74 mm × 76 mm pitch, 5.5 mm from the left/right edges and 4 mm from the top/bottom edges) follow the hand-measured drawing and match ADCS and EPS so the boards stack. Design rules are set to JLCPCB standard 2-layer limits (0.127 mm track/space). Not yet checked in 3D for assembly or ordered.

Layout

  • Floorplan by function. Power is bottom-left at the J1/J7 inputs. The MCU is centre-left beside the J8 header. The RFM98W radio and its antenna chain sit on the right edge at J3 (SMA) and J9 (dipole). I/O protection parts are directly above J2/J5/J6, and the temperature sensor sits between the MCU and the radio.
  • Spaced for hand soldering and probing. The median gap to the nearest part is about 2 mm, with about 3 mm around the MCU, radio module and debug pad.
  • Critical paths. The antenna path is 36 mm long, on the top layer only, with no vias. Each crystal sits next to its MCU pins with its tracks uncrossed, and each decoupling capacitor is at its supply pin.
  • Tracks. Signals are 0.15 mm, power 0.3 mm, and +3V3 0.2 mm (so it can leave the 0.5 mm-pitch MCU pins). The RF tracks are 0.6 mm.
  • Ground. GND is poured on both layers, with about 160 stitching vias. Surface-mount GND pads connect solidly to the pour (good for machine assembly, slower to hand-solder).
  • Manufacturing. There is no top-layer copper under the RFM98W module. The board has 3 fiducials for machine assembly, and teardrops on every pad and via except the fine-pitch U3/U4 pins.

History

This branch's git history keeps every earlier layout. To get one back, check out that commit's TTC/TTC_LoRa.kicad_pcb (or TTC_auto/TTC_auto.kicad_pcb for the auto-layout commits).

  • 23c6f7e: first fully routed layout (hand-placed).
  • d20aa38: the same layout with the crystal re-routed.
  • 16187b9: the same layout with teardrops and antenna-path vias added.
  • f9c4dad, deac0fd, b9867ab: auto-placed and auto-routed layouts. The current board is b9867ab.

Contents

  • TTC_LoRa.kicad_sch: schematic
  • TTC_LoRa.kicad_pcb: PCB layout (routed)
  • TTC_LoRa.kicad_pro: project configuration
  • TTC_LoRa.pdf: schematic PDF export
  • TTC.kicad_sym, Library.pretty/, sym-lib-table, fp-lib-table: project libraries (TPS7A2033 symbol, Tag-Connect footprint) needed to open the project

Tool

Designed in KiCad 10. Open TTC_LoRa.kicad_pro to view the full project.

Parts

105
QtyValueFootprintReferences
20TestPointTestPoint:TestPoint_Pad_1.0x1.0mmTP1, TP2, TP3, TP4, TP5, TP10, TP11, TP12, TP13, TP14, TP15, TP16, TP17, TP18, TP19, TP20 +4
11100nFCapacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolderC24, C25, C26, C27, C28, C30, C31, C32, C33, C34, C35
9Conn_01x02Connector_JST:JST_PH_B2B-PH-K_1x02_P2.00mm_VerticalJ1, J2, J3, J4, J5, J6, J7, J8, J9
610pCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC15, C16, C17, C18, C19, C20
647kResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR4, R5, R6, R7, R8, R9
6MCP6001-OTPackage_TO_SOT_SMD:SOT-23-5U6, U7, U8, U9, U10, U11
4100nFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC1, C4, C10, C14
44.7kResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR10, R11, R16, R17
4MountingHole_4mmMountingHole:MountingHole_4mmH1, H2, H3, H4
30.01uFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC6, C7, C11
31Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR1_0805, R1_806, R1_807
3100kResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR1, R2, R3
310kResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR12, R13, R14
310uFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC3, C9, C13
32.2uFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC5, C8, C12
210uFCapacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolderC36, C37
24.7uFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC23, C29
2Conn_01x02Connector_JST:JST_XH_B2B-XH-AM_1x02_P2.50mm_VerticalJ14, J15
10RResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR15
110nFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC22
11uFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC21
1Conn_01x03Connector_JST:JST_PH_B3B-PH-K_1x03_P2.00mm_VerticalJ11
1Conn_01x04Connector_JST:JST_PH_B4B-PH-K_1x04_P2.00mm_VerticalJ10
1Conn_01x08Connector_JST:JST_PH_B8B-PH-K_1x08_P2.00mm_VerticalJ12
1DRV8833PWP_XPackage_SO:HTSSOP-16-1EP_4.4x5mm_P0.65mm_EP3.4x5mm_Mask2.46x2.31mm_ThermalViasU3
1DRV8833PWP_YPackage_SO:HTSSOP-16-1EP_4.4x5mm_P0.65mm_EP3.4x5mm_Mask2.46x2.31mm_ThermalViasU4
1DRV8833PWP_ZPackage_SO:HTSSOP-16-1EP_4.4x5mm_P0.65mm_EP3.4x5mm_Mask2.46x2.31mm_ThermalViasU5
1STM32F446RETxPackage_QFP:LQFP-64_10x10mm_P0.5mmU1
1SWD_TagConnectConnector:Tag-Connect_TC2030-IDC-NL_2x03_P1.27mm_VerticalJ16

More from PARTH-KAKIRDE/CUBESAT

2
  • 2 layers85 × 84 mmTTC LoRa, the printed circuit board in 3D

    TTC LoRa

    PARTH-KAKIRDE/CUBESAT

    Radio (communications) module for the 2U CubeSat, LoRa version, Rev A.

    81 partsMIT
  • 2 layers85 × 84 mmCubeSat EPS, the printed circuit board in 3D

    CubeSat EPS

    PARTH-KAKIRDE/CUBESAT

    Radio (communications) module for the 2U CubeSat, LoRa version, Rev A.

    46 partsMIT

Similar boards

  • 2 layers228.4 × 85 mmLeChiffre, the printed circuit board in 3D

    LeChiffre

    tominabox1/Le-Chiffre-Keyboard

    Great thanks goes to Jake at P3D for really making the case amazing and open sourcing his work. Check him out at P3Dstore.com

    105 parts183GPL-3.0
  • 2 layers146.1 × 118.8 mmApiaster, the printed circuit board in 3D

    Apiaster

    nmunnich/apiaster

    Apiaster is a 50 key keyboard designed to be cheap, adjustable, and upgradeable.

    105 parts118
  • 2 layers63 × 81 mmEspLora, the printed circuit board in 3D

    EspLora

    BerkeleyHCI/PolymorphicBlocks

    A Python-based hardware description language for PCBs for higher-level (block-diagram / system-architecture level) PCB design through libraries of directly reusable subcircuit generators.

    105 parts94BSD-3-Clause
  • 2 layers70.5 × 100.2 mmAS3397 proto SMS, the printed circuit board in 3D

    AS3397 proto SMS

    PhysicsDptAngers/polyUAnalog

    Open source, analog and polyphonic synthesizer

    105 parts88MIT
  • 2 layers265.6 × 436 mmAhokore, the printed circuit board in 3D

    Ahokore

    dezlidezlidezli/ahokore

    Ahokore is a 36-key one-piece split keyboard, with full wireless functionality.

    105 parts84
  • 2 layers30.5 × 42.2 mm3bpV2Plus RevB, the printed circuit board in 3D

    3bpV2Plus RevB

    zaxour/TripleBypassV2Plus

    Variant of Tian Feng's Triple Bypass V2 with fixes and functionality added

    105 parts81
  • 2 layers248.3 × 99.8 mmLitl, the printed circuit board in 3D

    Litl

    mohoyt/litl

    Litl is an easy to build 40% keyboard using only through hole components.

    105 parts75

Questions

How big is the ADCS PCB?

It measures 85 × 84 mm and has 2 copper layers, 1.6 mm thick.

What parts does the ADCS use?

105 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the ADCS KiCad files?

From the PARTH-KAKIRDE/CUBESAT repository on GitHub, at the commit this page was made from: the board is ADCS/ADCS.kicad_pcb and its schematic ADCS/ADCS.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the ADCS design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).