Skip to the content
2 layers20.4 × 25 mmXT302+2 PCB mod, the printed circuit board in 3D

a PCB designed to keep small connectors of XT30(2+2) from failing when built properly

Size
20.4 × 25 mm
Copper layers
2
Thickness
1.6 mm
Parts
27
Nets
4
Pads
30
Tracks, vias
12, 18
Pours
12
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
31 Dec 2023
Updated
2 Mar 2024

Overview

XT302+2 PCB mod is an open-source printed circuit board by panglikesheep18, from the panglikesheep18/XT30-2plus2-connector-pcb repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 20.4 × 25 mm with 27 parts on 4 nets, routed with 12 tracks and 18 vias.

README

README.md

XT30-2plus2-connector-pcb

a PCB designed to keep small connectors from failing when attached

i made this PCB because i don't want to make makeshifts anymore 💀

Image

Board in KiCad (3 pieces per boards)

Features

  • holds small (data) connectors of male side of XT30 2+2 so it cannot be slipped of connecting thus breaking the connector

  • Holds 16AWG max. cables on main connectors and 24AWG max. on small (data) connectors

  • 3 boards per panel idk but this hopes to not make PCB makers mad

Usage

3D printers: swappable hotends (thermistor connects to small (data) connectors and the heater core connects to main connector)

idk what extra usage are but data or sensing goes to small (data) connectors and powered load goes to main connector.

Purchase assemblies

BOMs (not including solder and soldering iron)

##Things listed below can be found above (in "Purchase assemblies")

Board (excluding cables and solder)

  • 1X male side of XT30(2+2) or XT30U(2+2)

Load (excluding cables and solder)

  • 1X female side of XT30(2+2) or XT30APB(2+2)

Assembly procedure

Avoid pre-tinning the cable and PCB until the cable has fit through the board, unless you know what you're doing, otherwise you'll have a hard time solding the cable to the PCB.

  • fit cables to the PCB, make sure the cable going to the PCB is the one it connects, then solder cables to the board

  • put the connector to the PCB, make sure it fits

  • solder the connectors of XT30 2+2 and the PCB, Avoid heating it for too much as it will melt the connector and get the cable disconnected

Similar boards

  • 2 layers47.6 × 27.3 mmMmc usb 1, the printed circuit board in 3D

    Mmc usb 1

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    27 parts1.2k
  • 2 layers77.4 × 77.4 mmCORAZON LEDS CON FADE, the printed circuit board in 3D

    CORAZON LEDS CON FADE

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    27 parts915
  • 2 layers44.2 × 29.3 mmI2c tiny usb, the printed circuit board in 3D

    I2c tiny usb

    harbaum/I2C-Tiny-USB

    Cheap and simple I²C to USB interface

    27 parts454
  • 2 layers22 × 42 mmNvme bm to e, the printed circuit board in 3D

    Nvme bm to e

    CRImier/MyKiCad

    My KiCad boards. Can't be bothered uploading individually anymore, so here you go.

    27 parts253GPL-3.0
  • 2 layers80 × 61 mmPicoProducer, the printed circuit board in 3D

    PicoProducer

    pjgpetecodes/pico-streamdeck

    This project is an OBS Controller using a Raspberry Pi Pico and CircuitPython.

    27 parts230MIT
  • 2 layers186 × 45 mmAddOnD, the printed circuit board in 3D

    AddOnD

    freeDSP/freeDSP-aurora

    freeDSP ADAU1452 with 8 analog input, 8 analog outputs, S/P-DIF I/O, ADAT I/O, USB Audio Class2, WiFi, Bluetooth

    27 parts226CC-BY-SA-4.0
  • 2 layers29.6 × 40.6 mmDbwifi revB, the printed circuit board in 3D

    Dbwifi revB

    ugcs/ddc

    Drone Show Software is software designed for drone shows, allowing flight path planning as well as control of dozens of drones simultaneously in a synchronized manner.

    27 parts223

Questions

How big is the XT302+2 PCB mod PCB?

It measures 20.4 × 25 mm and has 2 copper layers, 1.6 mm thick.

What parts does the XT302+2 PCB mod use?

27 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the XT302+2 PCB mod KiCad files?

From the panglikesheep18/XT30-2plus2-connector-pcb repository on GitHub, at the commit this page was made from: the board is XT302+2 PCB mod/XT302+2 PCB mod.kicad_pcb and its schematic XT302+2 PCB mod/XT302+2 PCB mod.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the XT302+2 PCB mod design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).