

XT302+2 PCB mod
a PCB designed to keep small connectors of XT30(2+2) from failing when built properly
- Size
- 20.4 × 25 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 27
- Nets
- 4
- Pads
- 30
- Tracks, vias
- 12, 18
- Pours
- 12
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 31 Dec 2023
- Updated
- 2 Mar 2024
Overview
XT302+2 PCB mod is an open-source printed circuit board by panglikesheep18, from the panglikesheep18/XT30-2plus2-connector-pcb repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 20.4 × 25 mm with 27 parts on 4 nets, routed with 12 tracks and 18 vias.
README
README.mdXT30-2plus2-connector-pcb
a PCB designed to keep small connectors from failing when attached
i made this PCB because i don't want to make makeshifts anymore 💀
Image
Features
-
holds small (data) connectors of male side of XT30 2+2 so it cannot be slipped of connecting thus breaking the connector
-
Holds 16AWG max. cables on main connectors and 24AWG max. on small (data) connectors
-
3 boards per panel idk but this hopes to not make PCB makers mad
Usage
3D printers: swappable hotends (thermistor connects to small (data) connectors and the heater core connects to main connector)
idk what extra usage are but data or sensing goes to small (data) connectors and powered load goes to main connector.
Purchase assemblies
- i don't sell PCBs but you can send the gerber to JLCPCB or PCBWay
- Also some AMASS XT30 2+2s in AliExpress
BOMs (not including solder and soldering iron)
##Things listed below can be found above (in "Purchase assemblies")
Board (excluding cables and solder)
- 1X male side of XT30(2+2) or XT30U(2+2)
Load (excluding cables and solder)
- 1X female side of XT30(2+2) or XT30APB(2+2)
Assembly procedure
Avoid pre-tinning the cable and PCB until the cable has fit through the board, unless you know what you're doing, otherwise you'll have a hard time solding the cable to the PCB.
-
fit cables to the PCB, make sure the cable going to the PCB is the one it connects, then solder cables to the board
-
put the connector to the PCB, make sure it fits
-
solder the connectors of XT30 2+2 and the PCB, Avoid heating it for too much as it will melt the connector and get the cable disconnected
Similar boards
- 2 layers47.6 × 27.3 mm

- 2 layers77.4 × 77.4 mm

CORAZON LEDS CON FADE
hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!
27 parts915 - 2 layers44.2 × 29.3 mm

- 2 layers40 × 40 mm

- 2 layers22 × 42 mm

Nvme bm to e
CRImier/MyKiCad
My KiCad boards. Can't be bothered uploading individually anymore, so here you go.
27 parts253GPL-3.0 - 2 layers80 × 61 mm

PicoProducer
pjgpetecodes/pico-streamdeck
This project is an OBS Controller using a Raspberry Pi Pico and CircuitPython.
27 parts230MIT - 2 layers186 × 45 mm

AddOnD
freeDSP/freeDSP-aurora
freeDSP ADAU1452 with 8 analog input, 8 analog outputs, S/P-DIF I/O, ADAT I/O, USB Audio Class2, WiFi, Bluetooth
27 parts226CC-BY-SA-4.0 - 2 layers29.6 × 40.6 mm

Dbwifi revB
ugcs/ddc
Drone Show Software is software designed for drone shows, allowing flight path planning as well as control of dozens of drones simultaneously in a synchronized manner.
27 parts223
Questions
How big is the XT302+2 PCB mod PCB?
It measures 20.4 × 25 mm and has 2 copper layers, 1.6 mm thick.
What parts does the XT302+2 PCB mod use?
27 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the XT302+2 PCB mod KiCad files?
From the panglikesheep18/XT30-2plus2-connector-pcb repository on GitHub, at the commit this page was made from: the board is XT302+2 PCB mod/XT302+2 PCB mod.kicad_pcb and its schematic XT302+2 PCB mod/XT302+2 PCB mod.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the XT302+2 PCB mod design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).