

Dcpsu card b
DCPSU - schematics and PCB layouts
- Size
- 80 × 105 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 91
- Nets
- 77
- Pads
- 385
- Tracks, vias
- 547, 110
- Pours
- 10
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 25 Jun 2021
- Updated
- 2 Mar 2021
Overview
Dcpsu card b is an open-source printed circuit board by orb1t-ua, from the orb1t-ua/dcpsu-pcb repository on GitHub. It is a 2-layer board of 80 × 105 mm with 91 parts on 77 nets, routed with 547 tracks and 110 vias.
It is built around the ATTINY87-MU, AOZ2151PQI-10 and NCP5623DTB, with the LM358DR, LD1084V and LM334M among its other parts. Its parts include 37 resistors, 27 capacitors, 10 ICs, 5 connectors and 3 diodes. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
7ATTINY87-MU
QFN-32-40℃~+85℃ 1.8V~5.5V 10bit 16 16MHz 512Byte 512Byte 8 Bit 8KB AVR Built-in FLASH VQFN-32-EP(5x5) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)AOZ2151PQI-10
QFN-18(3x3)-40℃~+85℃ 1 12V~28V 4A Adjustable Buck Buck Built-in QFN-18(3x3) DC-DC Converters ROHSAlpha & Omega SemiconductorDC-DC ConvertersNCP5623DTB
TSSOP-14-4.5mm-40℃~+85℃ 1MHz 2.7V 3 3% 37mA Analog、PWM TSSOP-14-4.5mm LED Drivers ROHSonsemiLED DriversLM358DR
UncategorisedUnknown makerLD1084V
TO-220-40℃~+125℃@(Tj) 1 1.25V~28.5V 1.5V@(5A) 10mA 30V 5A 72dB@(120Hz) Adjustable Positive Short Circuit Protection、Thermal shutdown TO-220 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSSTMicroelectronicsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsLM334M
SOIC-80℃~+70℃ 10mA 1V~40V Current Source Programmable output current ±6% SOIC-8 Current Source / Constant Current Source ROHSTexas InstrumentsCurrent Source / Constant Current SourceSSM6N7002KFU,LF
SOT-3631.1V 1.2Ω@4.5V 1.3pF 2 N-Channel 300mA 40pF 5.5pF 500mW 600pC@4.5V 60V N-Channel SOT-363 MOSFETs ROHSToshibaMOSFETs
README
README.mddcpsu-pcb
DCPSU - schematics and PCB layouts
Card A:
- High efficiency
- Rough voltage output control
- Main use case is computer power supply
Card B:
- Fine voltage output control
- Current limiting
- Main use case is benchtop lab power supply
Backplane-testboard:
- Platform for card testing/development
Component selection/design
LICENSE
Parts
91| Qty | Value | Footprint | References |
|---|---|---|---|
| 14 | 0.1u | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C1, C3, C4, C5, C6, C8, C10, C11, C12, C17, C23, C24, C25, C26 |
| 10 | 100 | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R7, R8, R16, R25, R28, R30, R31, R32, R33, R34 |
| 9 | 10k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R1, R2, R3, R4, R5, R6, R15, R18, R37 |
| 6 | 10u | Capacitor_SMD:C_1206_3216Metric_Pad1.42x1.75mm_HandSolder | C9, C13, C15, C20, C21, C22 |
| 5 | 2k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R9, R13, R14, R19, R20 |
| 4 | 18k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R10, R12, R35, R36 |
| 4 | 22u | Capacitor_SMD:C_1206_3216Metric_Pad1.42x1.75mm_HandSolder | C14, C16, C18, C19 |
| 3 | 18k 0.1% | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R26, R27, R29 |
| 3 | 1u | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C2, C7, C27 |
| 2 | 10 | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R23, R24 |
| 2 | 1k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R11, R17 |
| 2 | 200m | Resistor_SMD:R_1206_3216Metric_Pad1.42x1.75mm_HandSolder | R21, R22 |
| 2 | Conn_01x01_Female | Connector_Wire:SolderWirePad_1x01_Drill1.5mm | J4, J5 |
| 2 | D_Schottky | custom-footprints:TO-277B-MBR860S | D2, D3 |
| 2 | LM358DR | digikey-footprints:SOIC-8_W3.9mm | U3, U6 |
| 1 | 10k 0.05% | Resistor_SMD:R_Array_Convex_2x0606 | RN2 |
| 1 | 10uH | custom-footprints:L_Pad4.05x4.4mm_LMLP1011 | L1 |
| 1 | 1k 0.05% | Resistor_SMD:R_Array_Convex_2x0606 | RN1 |
| 1 | AOZ2151PQI-10 | custom-footprints:QFN-20-2EP_3x3mm_AOZ2151PQI-10 | U5 |
| 1 | ATtiny87-MU | Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.1x3.1mm | U1 |
| 1 | AVR-ISP-6 | Connector_IDC:IDC-Header_2x03_P2.54mm_Vertical | J2 |
| 1 | Conn_01x06 | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J3 |
| 1 | INA219AIDCNR | Package_TO_SOT_SMD:SOT-23-8_Handsoldering | U10 |
| 1 | LD1084 | Package_TO_SOT_THT:TO-220-3_Vertical | U8 |
| 1 | LM334M | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U9 |
| 1 | MCP1501T-20E | digikey-footprints:SOT-23-6 | VR1 |
| 1 | MCP4017T-103E_LT | digikey-footprints:SOT-363 | U7 |
| 1 | MCP47FEB22A0T-E_ST | digikey-footprints:TSSOP-8_W4.4mm | U4 |
| 1 | NCP5623 | digikey-footprints:TSSOP-14_W4.4mm | U2 |
| 1 | PCIe_x1 | Connector_PCBEdge:BUS_PCIexpress | J1 |
| 1 | PinHeader_1x02_P2.54mm_Vertical | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | Jx1 |
| 1 | QLS6B-FKW | custom-footprints:QLS6B-FKW | D1 |
| 1 | SSM6N7002KFU,LF | digikey-footprints:SOT-363 | Q1 |
The 88 most common of 91 parts.
More from orb1t-ua/dcpsu-pcb
2- 2 layers80 × 100 mm

- 2 layers165 × 45 mm

Similar boards
- 4 layers236.1 × 156.9 mm

- 4 layers26.8 × 30 mm

- 2 layers94 × 85 mm

- 4 layers65 × 30.5 mm

- 2 layers80 × 80 mm

Reflow oven rev-001
edenbarby/reflow-oven
A DIY reflow oven with a little inspiration from the internet.
88 parts - 4 layers13.1 × 18.1 mm

74xx quad logic
marsairforce/breakout_boards
Small circuit boards to assist with breadboard prototyping with SMD packages.
22 parts39Unlicense - 2 layers40 × 40 mm

Tinkerforge industrial dual relay bricklet industrial dual relay
oomlout/oomlout_oomp_project_bot_v_2
34 parts - 4 layers157.5 × 88.2 mm

Questions
How big is the Dcpsu card b PCB?
It measures 80 × 105 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Dcpsu card b use?
91 parts, built around the ATTINY87-MU, AOZ2151PQI-10, NCP5623DTB and LM358DR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Dcpsu card b KiCad files?
From the orb1t-ua/dcpsu-pcb repository on GitHub, at the commit this page was made from: the board is dcpsu-card-b.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Dcpsu card b design in my own project?
Its repository states no licence, so its author keeps all rights: ask orb1t-ua before reusing the design.