2 layers97.5 × 79 mm
RGB LED Driver
PCB-Design-MIT/Wi-Fi-Controlled-RGB-Light
A demo board for students to learn to solder and debug
144 parts4
2 layers76.5 × 78 mm
Hardware for the emonTH3 temperature, humidity, and pulse sensing node
- Size
- 76.5 × 78 mm
- Copper layers
- 2
- Thickness
- 1.67 mm
- Parts
- 56
- Nets
- 55
- Pads
- 197
- Tracks, vias
- 294, 85
- Pours
- 5
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 21 Nov 2024
- Updated
- 16 Oct 2026
Overview
EmonTH is an open-source printed circuit board by openenergymonitor, from the openenergymonitor/emonTH3 repository on GitHub, published under the CC-BY-SA-4.0 licence. It is a 2-layer board of 76.5 × 78 mm with 56 parts on 55 nets, routed with 294 tracks and 85 vias.
It is built around the ATSAML10E15A-MF, HDC2010YPAR and TPS61291DRV, with the AP2112K-3.3TRG1, LQG15HS15NJ02D and MDMK2020T3R3MM among its other parts. Its parts include 15 resistors, 9 capacitors, 6 connectors, 5 ICs and 3 diodes. It belongs with the SAM D and SAM boards of this library.
Main components
10
ATSAML10E15A-MF
VQFN-32(5x5)-40℃~+125℃ 1.62V~3.63V 10bit 12bit 25 2KB 32 Bit 32KB 32MHz 8KB ARM Cortex-M23 Built-in FLASH VQFN-32(5x5) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)
HDC2010YPAR
DSBGA-6-40℃~+85℃ 0%RH~100%RH 1.62V~3.6V 11bit 550nA I2C ±0.2℃ ±2%RH DSBGA-6 Temperature and Humidity Sensor ROHSTexas InstrumentsTemperature And Humidity Sensor
TPS61291DRV
WSON-6-EP(2x2)-40℃~+85℃@(TA) 1 2.5V、3V、3.3V 5.7uA 700mA 900mV~5V Adjustable Boost Boost Built-in Yes WSON-6-EP(2x2) DC-DC Converters ROHSTexas InstrumentsDC-DC Converters
AP2112K-3.3TRG1
SOT-25-5-40℃~+85℃@(Ta) 1 250mV@(600mA) 3.3V 50uVrms 55uA 600mA 65dB@(1kHz) 6V Fixed Over Current Protection、Thermal Shutdown、Enable control Positive SOT-25-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSDiodes IncorporatedVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
LQG15HS15NJ02D
040215nH 2.5GHz 320mΩ 450mA 8@100MHz ±5% 0402 Inductors (SMD) ROHSMurataInductors (SMD)MDMK2020T3R3MM
SMD,2x2mm1.15A 1.35A 155mΩ 3.3uH ±20% SMD,2x2mm Power Inductors ROHSTaiyo YudenPower InductorsANT-433-HETH
插件-40℃~+80℃ 1.9dBi 2 40MHz 433MHz 50Ω 8.89mm Spring antenna 插件 Antennas ROHSTE ConnectivityAntennasRS1-05-G
插件,P=2.54mm-40℃~+105℃ 1 2.54mm 250V 3A 5P 8.51mm Brass Gold Square Hole 插件,P=2.54mm Female Headers ROHSADAM TECHFemale HeadersPH1-06-UA
插件,P=2.54mm-40℃~+105℃ 1 2.54mm 250V 3A 6P Black Brass Gold Through Hole 插件,P=2.54mm Pin Headers ROHSADAM TECHPin Headers
219-2MST
SMD,P=2.54mm-55℃~+85℃ 100mA 2 2.54mm 20V Black SPST Slide, Recessed SMD,P=2.54mm DIP Switches ROHSCTS Electronic ComponentsDIP Switches
README
README.mdemonTH3
Introduction
The Energy Monitor Temperature Humidity 3 (emonTH3) is an ultra low power temperature and humidity monitoring node with support for pulse counting and additional external sensors.
It is an update to the OpenEnergyMonitor emonTH2 with the following goals:
- Increase the battery life from the current ~4 years on 2xAA
- Update to modern components
- Reduce the overall cost of the system
- Provide user expansion for other sensors
- ATSAML10E15A-MU Microprocessor
- TI HDC2010 Low-Power Humidity and Temperature Digital Sensors
- Sensirion SEK-STCC4 Co2 sensor (optional)
It should be used with the emonTH-fw firmware.
Getting started
The board is designed using KiCAD version 9. The schematic and floorplan are provided as PDF files. If you want to render your own files, run ./generate.py. This produces Gerber files as well as KiCAD PCB and schematic files tagged with the git commit for traceability.
[!NOTE] The emonTH3 will be available fully assembled and programmed from the OpenEnergyMonitor shop.
Feedback and Issues
These can be reported:
- as a GitHub issue
- on the OpenEnergyMonitor forums
Contributing
As the hardware design flow doesn't quite follow as nicely as software, if you want to contribute a change, please raise an issue as described above and we can collaborate.
After cloning the repository, run ./install-hooks.sh to add the render on commit.
References
Acknowledgements
- Glyn Hudson and Trystan Lea @ OpenEnergyMonitor
- Gordon Davidson @ OpenEnergyMonitor Forums
Parts
56| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 470K | Resistor_SMD:R_0402_1005Metric | R2, R3, R8, R10, R14, R15 |
| 5 | 100n | Capacitor_SMD:C_0402_1005Metric | C1, C2, C3, C7, C9 |
| 5 | 1K | Resistor_SMD:R_0402_1005Metric | R1, R7, R9, R12, R17 |
| 4 | MountingHole | MountingHole:MountingHole_3.2mm_M3_DIN965 | H1, H2, H3, H4 |
| 3 | 4K7 | Resistor_SMD:R_0402_1005Metric | R4, R5, R6 |
| 3 | TestPoint | TestPoint:TestPoint_Pad_D1.0mm | TP1, TP2, TP3 |
| 2 | LED | LED_SMD:LED_0603_1608Metric | D1, D3 |
| 2 | SW_Push | Button_Switch_SMD:SW_Tactile_SPST_NO_Straight_CK_PTS636Sx25SMTRLFS | SW2, SW3 |
| 1 | 100K | Resistor_SMD:R_0402_1005Metric | R11 |
| 1 | 10p | Capacitor_SMD:C_0402_1005Metric | C5 |
| 1 | 10u | Capacitor_SMD:C_0805_2012Metric | C4 |
| 1 | 15n | Inductor_SMD:L_0402_1005Metric | L2 |
| 1 | 1u | Capacitor_SMD:C_0402_1005Metric | C8 |
| 1 | 22u | Capacitor_SMD:C_0805_2012Metric | C6 |
| 1 | 3u3 | Inductor_SMD:L_Taiyo-Yuden_MD-2020 | L1 |
| 1 | AP2112K-3.3 | Package_TO_SOT_SMD:SOT-23-5 | U7 |
| 1 | ATSAML10E15A-MUT | Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.45x3.45mm | U5 |
| 1 | Antenna | ant-433:ANT-433-HETH | AE1 |
| 1 | Battery | Battery:BatteryHolder_Keystone_2468_2xAAA | BT1 |
| 1 | Conn_01x03 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J3 |
| 1 | Conn_01x05 | Connector_PinSocket_2.54mm:PinSocket_1x05_P2.54mm_Vertical | J6 |
| 1 | Conn_01x06 | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J7 |
| 1 | Conn_ARM_JTAG_SWD_10 | Connector_PinHeader_1.27mm:PinHeader_2x05_P1.27mm_Vertical_SMD | J2 |
| 1 | D_Schottky | Diode_SMD:D_SOD-523 | D2 |
| 1 | FerriteBead_Small | Inductor_SMD:L_0402_1005Metric | FB1 |
| 1 | Fiducial | Fiducial:Fiducial_0.5mm_Mask1mm | FID1 |
| 1 | HDC2010 | hdc2010:DSBGA-6 | U1 |
| 1 | LOGO | graphics:starlings | G*** |
| 1 | MountingHole | MountingHole:MountingHole_2.7mm_M2.5_DIN965 | H5 |
| 1 | RFM69W | RF_Module:HOPERF_RFM69HW | U8 |
| 1 | SW_DIP_x02 | Button_Switch_SMD:SW_DIP_SPSTx02_Slide_6.7x6.64mm_W8.61mm_P2.54mm_LowProfile | SW1 |
| 1 | Screw_Terminal_01x05 | TerminalBlock_Phoenix:TerminalBlock_Phoenix_PT-1,5-5-3.5-H_1x05_P3.50mm_Horizontal | J5 |
| 1 | Screw_Terminal_01x06 | TerminalBlock_Phoenix:TerminalBlock_Phoenix_PT-1,5-6-3.5-H_1x06_P3.50mm_Horizontal | J1 |
| 1 | TPS61291 | Package_SON:WSON-6-1EP_2x2mm_P0.65mm_EP1x1.6mm | U4 |
Similar boards
- 2 layers64 × 80 mm
Esp8266 test board (Copie en conflit de Steven 2015-08-28)
sifourquier/domotic_esp_hardware
hardware for a system based on esp8266
120 parts - 2 layers25 × 30 mm
- 4 layers97 × 105.5 mm
STARDRIVE SHIELD V1 0
themarcolab/Stardrive-Shield
With STARDRIVE SHIELD you can implement from 6 step to FOC motor control algorithms.
193 parts2 - 4 layers90 × 66 mm
Audio
AndreasNielsen4000/Group-7-IoT-Project
The project is a wireless speaker system that can play music from a Bluetooth or WiFi source. The system consists of four main parts with subcomponents:
162 parts1 - 2 layers36.2 × 43.9 mm
- 4 layers73.1 × 69.8 mm
Stm32u595-breakout
oresat/oresat-kicad
All things KiCAD for OreSat; libraries, tools, settings, etc.
85 parts6 - 2 layers55 × 40.1 mm
First design
kian09/Guardian
A compact health monitoring device that is worn on the wrist. Its capabilities are measuring your heart rate and detecting accidental falls using an accelerometer.
55 parts
Questions
How big is the EmonTH PCB?
It measures 76.5 × 78 mm and has 2 copper layers, 1.67 mm thick.
What parts does the EmonTH use?
56 parts, built around the ATSAML10E15A-MF, HDC2010YPAR, TPS61291DRV and AP2112K-3.3TRG1. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the EmonTH KiCad files?
From the openenergymonitor/emonTH3 repository on GitHub, at the commit this page was made from: the board is emonTH.kicad_pcb and its schematic emonTH.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the EmonTH design in my own project?
Its repository publishes it under the CC-BY-SA-4.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).