
Vetrnik control
ondras12345/vetrnik
Electronics for heating water with power from a 2 kW wind turbine

Electronics for heating water with power from a 2 kW wind turbine
Vetrnik power is an open-source printed circuit board by ondras12345, from the ondras12345/vetrnik repository on GitHub. It is a 2-layer board of 124.5 × 99.1 mm with 138 parts on 97 nets, routed with 969 tracks and 72 vias.
It is built around the ATMEGA8-16PU, IR2104PBF and LTV-817, with the H11L1, LM393 and LTV-847 among its other parts. Its parts include 47 resistors, 32 capacitors, 17 connectors, 12 ICs and 10 transistors. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Power electronics for heating water using power generated by a small wind turbine.

The device offers a feature-rich command line interface:
vetrnik-control:$ help
---- Available commands ----
SPIflash: Issue commands to SPI flash
conf: Get or set configuration options.
control: Get or set params of control algorithm.
debug: Filter debug messages
dfu: Switch to DFU firmware download mode.
ds18b20: Print out DS18B20 sensor readings
free: Print out amount of free memory.
ifconfig: Print out networking information.
lisp: Process a line of Lisp
lisp_read: Execute Lisp from file
lisp_reset: Reinit Lisp interpreter
log: Print log / postmort
millis: Returns the number of milliseconds passed since the program started.
mqtt: Print out MQTT status.
onewirescan: Scan devices on onewire bus
ota: Switch to over-the-air firmware dl mode.
power: Print status of power PCB or set params.
pump: Control circulation pump.
reset: Reset the MCU.
rx: Print out RX_datapoints.
rx_raw: Toggle printing of messages from power board.See hardware/.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 13 | 100n | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C2, C3, C4, C5, C10, C18, C19, C21, C25, C26, C27, C31, C32 |
| 11 | 10k | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R10, R19, R20, R21, R22, R31, R32, R38, R41, R42, R44 |
| 7 | BC846 | Package_TO_SOT_SMD:SOT-23 | Q3, Q4, Q5, Q6, Q7, Q8, Q10 |
| 5 | 1M | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R2, R15, R16, R17, R18 |
| 5 | 1k | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R1, R4, R5, R9, R47 |
| 5 | 1k5 | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R8, R11, R12, R13, R14 |
| 4 | 10 | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R33, R34, R36, R37 |
| 4 | 3k3 | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R7, R24, R28, R30 |
| 4 | LTV-817 | Package_DIP:DIP-4_W7.62mm | U1, U2, U5, U10 |
| 4 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H1, H2, H3, H4 |
| 3 | 10n | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C28, C29, C30 |
| 3 | 1u / 25V | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C13, C16, C24 |
| 3 | 47k | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R25, R29, R46 |
| 2 | 1.5KE200CA | Diode_THT:D_DO-201AE_P15.24mm_Horizontal | D1, D3 |
| 2 | 100k / 0,6W | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R23, R27 |
| 2 | 100n / 275VAC | Capacitor_THT:C_Rect_L26.5mm_W10.5mm_P22.50mm_MKS4 | C6, C7 |
| 2 | 220u | Capacitor_THT:CP_Radial_D8.0mm_P3.50mm | C11, C17 |
| 2 | 22p | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C22, C23 |
| 2 | 22u / 35V | Capacitor_THT:CP_Radial_D5.0mm_P2.00mm | C12, C15 |
| 2 | 470u / 250V | Capacitor_THT:CP_Radial_D30.0mm_P10.00mm_SnapIn | C8, C9 |
| 2 | 4k7 | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R3, R45 |
| 2 | BC847 | Package_TO_SOT_SMD:SOT-23 | Q2, Q9 |
| 2 | H11L1 | Package_DIP:DIP-6_W7.62mm_LongPads | U3, U4 |
| 2 | IR2104 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U8, U9 |
| 2 | Jumper | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | JP1, JP2 |
| 2 | TestPoint_2Pole | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | TP1, TP2 |
| 2 | UF4004 | Diode_THT:D_DO-41_SOD81_P10.16mm_Horizontal | D2, D4 |
| 1 | 10 | Resistor_THT:R_Axial_DIN0309_L9.0mm_D3.2mm_P12.70mm_Horizontal | R35 |
| 1 | 100k | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R43 |
| 1 | 12V / 0,9A max | Connector_Molex:Molex_KK-254_AE-6410-02A_1x02_P2.54mm_Vertical | M1 |
| 1 | 12V IN | Connector_Molex:Molex_KK-254_AE-6410-02A_1x02_P2.54mm_Vertical | J1 |
| 1 | 15n / 300VAC | Capacitor_THT:C_Rect_L18.0mm_W5.0mm_P15.00mm_FKS3_FKP3 | C14 |
| 1 | 16MHz | Crystal:Crystal_HC49-U_Vertical | Y1 |
| 1 | 1N4148W | Diode_SMD:D_SOD-123 | D5 |
| 1 | 22k | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R26 |
| 1 | 22k 5W | Resistor_THT:R_Axial_DIN0922_L20.0mm_D9.0mm_P30.48mm_Horizontal | R40 |
| 1 | 330 | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R39 |
| 1 | 330n | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C20 |
| 1 | 470 | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R6 |
| 1 | 470u / 25V | Capacitor_THT:CP_Radial_D10.0mm_P5.00mm | C1 |
| 1 | AC frequency sense | Connector_Molex:Molex_KK-254_AE-6410-02A_1x02_P2.54mm_Vertical | J14 |
| 1 | AC1 | ondra:FS1536 | J10 |
| 1 | AC2 | ondra:FS1536 | J11 |
| 1 | ACS712 | Connector_Molex:Molex_KK-254_AE-6410-03A_1x03_P2.54mm_Vertical | J17 |
| 1 | ACS712_2 | Connector_Molex:Molex_KK-254_AE-6410-03A_1x03_P2.54mm_Vertical | J16 |
| 1 | ATmega8-16PU | Package_DIP:DIP-28_W7.62mm_Socket | U12 |
| 1 | AVR RESET | Button_Switch_THT:SW_PUSH_6mm_H4.3mm | SW1 |
| 1 | AVR-ISP-6 | Connector_IDC:IDC-Header_2x03_P2.54mm_Vertical | J15 |
| 1 | BAV99 | Package_TO_SOT_SMD:SOT-23 | D6 |
| 1 | BCP56-16 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | Q1 |
| 1 | DC IN | ondra:DG270-10.0-02P-14-00A | J6 |
| 1 | ENABLE | Connector_Molex:Molex_KK-254_AE-6410-02A_1x02_P2.54mm_Vertical | J4 |
| 1 | G #Q1 | Connector_Molex:Molex_KK-254_AE-6410-02A_1x02_P2.54mm_Vertical | J8 |
| 1 | G #Q2 | Connector_Molex:Molex_KK-254_AE-6410-02A_1x02_P2.54mm_Vertical | J9 |
| 1 | G #Q3 | Connector_Molex:Molex_KK-254_AE-6410-02A_1x02_P2.54mm_Vertical | J12 |
| 1 | G #Q4 | Connector_Molex:Molex_KK-254_AE-6410-02A_1x02_P2.54mm_Vertical | J13 |
| 1 | L78L05_TO92 | Package_TO_SOT_THT:TO-92L_HandSolder | U11 |
| 1 | LM393 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U7 |
| 1 | LTV-847 | Package_DIP:DIP-16_W7.62mm | U6 |
| 1 | Net-Tie_2 | NetTie:NetTie-2_SMD_Pad2.0mm | NT1 |
| 1 | PE | ondra:FS1536 | J7 |
| 1 | RELAYS | Connector_Molex:Molex_KK-254_AE-6410-06A_1x06_P2.54mm_Vertical | J5 |
| 1 | TBA 1-1212 | Converter_DCDC:Converter_DCDC_Murata_MEE1SxxxxSC_THT | PS1 |
| 1 | TT7-10KC3-11 | Connector_Molex:Molex_KK-254_AE-6410-02A_1x02_P2.54mm_Vertical | TH1 |
| 1 | UART | Connector_Molex:Molex_KK-254_AE-6410-04A_1x04_P2.54mm_Vertical | J3 |
| 1 | ~{SHORT} | Connector_Molex:Molex_KK-254_AE-6410-03A_1x03_P2.54mm_Vertical | J2 |

ondras12345/vetrnik
Electronics for heating water with power from a 2 kW wind turbine

ondras12345/vetrnik
Electronics for heating water with power from a 2 kW wind turbine

ondras12345/vetrnik
Electronics for heating water with power from a 2 kW wind turbine

ondras12345/vetrnik
Electronics for heating water with power from a 2 kW wind turbine

ondras12345/vetrnik
Electronics for heating water with power from a 2 kW wind turbine

ondras12345/vetrnik
Electronics for heating water with power from a 2 kW wind turbine

ondras12345/vetrnik
Electronics for heating water with power from a 2 kW wind turbine

eerdemgundogdu/avtech-agv-main
Software and carrier PCB design for a line-following forklift AGV built by CU AVTECH for the Sanayide Robotik Uygulamalar 2026 competition.


tonycung/0-10V-to-4-20mA-Converter
A simple 0–10 V to 4–20 mA analog signal converter designed with KiCad.

Enthusela/DesktopControlPanel
An open-source, hand-built, tactile, home-brew smart-home hub with analog PC audio monitoring and control.

ondras12345/CNC
My CNC 1610 and Stepcraft model 600 configuration and CNC-related notes


fberni21/taller-circuitos
FIUBA - Electrónica - Taller de Diseño de Circuitos Electrónicos

It measures 124.5 × 99.1 mm and has 2 copper layers, 1.5 mm thick.
138 parts, built around the ATMEGA8-16PU, IR2104PBF, LTV-817 and H11L1. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the ondras12345/vetrnik repository on GitHub, at the commit this page was made from: the board is hardware/vetrnik-power/vetrnik-power.kicad_pcb and its schematic hardware/vetrnik-H-bridge/vetrnik-H-bridge.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask ondras12345 before reusing the design.