Skip to the content
2 layers60 × 50 mmAD8237DevBoard, the printed circuit board in 3D

AD8237DevBoard

oihdesigns/Micro-DMM2

A small, open hardware DMM

Size
60 × 50 mm
Copper layers
2
Thickness
1.6 mm
Parts
56
Nets
26
Pads
133
Tracks, vias
527, 54
Pours
2
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
22 Jun 2025
Updated
1 Nov 2026

Overview

AD8237DevBoard is an open-source printed circuit board by oihdesigns, from the oihdesigns/Micro-DMM repository on GitHub. It is a 2-layer board of 60 × 50 mm with 56 parts on 26 nets, routed with 527 tracks and 54 vias.

It is built around the AD8237ARMZ, OPA333AIDBVR-MS and TCA9536DGKR, with the TMUX1104DGS among its other parts. Its parts include 20 resistors, 12 capacitors, 4 ICs and 4 connectors.

Main components

4

README

README.md

20250623_204616_470_1DXII copy

Update Late August '25:

I've recently started a new job. It's great, but has longer hours than my previous job. This will negatively affect the amount of time I put into this project...

Micro-DMM

This is the PCB design and code for a 4.5 digit DMM/ instrumentation module. It is designed and written primairly for Arduino-style development boards.

I've developed this DMM in my work testing and troubleshooting electronics to make my life easier.

I've had Deep-Wiki index my documentation. It did a mostly okay job. You can read its summary here: Ask DeepWiki

20250623_205912_480_1DXII copy

The main features are:

  • The most recent designs have open-lead detection in voltmeter mode. I believe this makes it the first voltmeter in exisitance that can automatically, safely, and positively tell the difference between "there is low impedance between these points" vs "current does not and can not flow between these two points." Please see the white paper for details.
  • Using keyboard emulation to directly type values into a computer for me. (Extremely useful when troubleshooting a populated PCB - you can quickly ohm out both the problem board and a good one directly into Excel to look for different impedances between given contacts.)
  • Very sensitive low-resistance readings (accurate to better than 0.01 Ohms with proper lead zeroing).
  • LED blinks when I'm reading logic level voltage or higher.
  • Simultaneous current and voltage measurement abilities (requires a Hall sensor-based ammeter module).
  • Data logging for current and voltage, with customizable triggers to autolog both.

Raspberry Pi user interface

The repository now includes a Raspberry Pi-friendly interface that mirrors the firmware display and logging features. The UI is written in Python using Tkinter so it ships with Raspberry Pi OS and can run directly on the framebuffer or under X11. To start the dashboard with the built-in demo generator run:

text
python3 -m raspi_port.app

In deployment the measurement host should feed real readings to the MicroDmmApp class instead of the demo thread. The window presents the same information rendered by updateDisplay()—live voltage or resistance with min/max tracking, current when enabled, the active mode, timestamps, delta/null information, and log counters. Interaction hotkeys replace the touch panel:

FunctionTouch colorHotkeyDescription
Mode cycleRedMAdvances through the measurement modes.
Manual logGreenLAppends the most recent sample buffer to ~/micro_dmm_logs/data.csv.
Auto log export–AWrites the auto-log buffer to ~/micro_dmm_logs/data_autologged.csv.
Min/Max resetBlueZClears the stored extrema, just like tapping “Min/Max”.
Type/ΔYellowTIn Type mode it writes the displayed value to typed_entries.txt; otherwise it arms the delta/null workflow.

On a Raspberry Pi you can optionally map these controls to hardware buttons by defining a MICRO_DMM_GPIO environment variable before launching the program. The value is a comma-separated list such as mode=5,manual_log=6,auto_log=13,minmax=19,type=26. Each entry binds a GPIO pin (using gpiozero.Button) to the corresponding action.

All log exports stay on the Pi’s filesystem under ~/micro_dmm_logs/. The CSV layouts match the firmware’s logCurrentData() and autologArraysToCSV() routines so downstream tooling continues to work. The typed_entries.txt file replaces the USB keyboard emulator and captures the same formatted text that would have been “typed” into a host PC, while also echoing it to stdout for quick clipboard-style use.

I have a long and detailed write-up of the circuitry design on my personal website: https://www.oihdesigns.com/arduino-multimeter-project

There are a couple videos here: https://youtu.be/rzj-ar2Qv_A and here: https://youtu.be/hZ4eH-7RNsU

Here are more photos:

20250623_205043_760_1DXII copy 20250623_202545_180_1DXII copy 20250623_203203_470_1DXII copy

Design Prioities and Compromises:

This meter is designed to complement and support the more expensive equimpent generally found in a lab, rather than replace it. With that in mide, I've made the following design decisions on my priorites:

Minimal Protections

  • The voltmeter circuitry is not designed to measure amplitudes higher than is dangerous to humans. By not designing a tool that is supposed to keep people safe I can dramatically simplify and shrink the design. (The said, I've nailed the voltmeter circuit with a 1000V megaohmmeter. No problem.)
  • Likewise, the resistance circuit can be damaged if you accidentally measure too much /unregulated voltage. This is a tradeoff for a very fast and accurate autoranging ohmmeter circuit that can accurately read from less than 0.01 to more than 5,000,000 Ohms.

Streamlined Functions

  • There is no built in ammeter, inductance, or capacitance function. Ammeter function is easily added as needed with either an off-the-shelf module, or a low value resistor across the voltmeter. There isn't an easy way to add indutance or capacitance. I don't use any of these often enough for them to be worth taking up the PCB space.

Current Support:

As of writing I have functional versions (I confirmed the core functions work) that support the:

  • Arduino Uno R4
  • Arduino Giga (with or without the display shield)
  • Arduino ESP32 Nano (via jumpers)
  • Seeed Studio XIAO RA4M1 (same processer as the Uno R4)
  • I have partial function on a direct computer (Windows 11) interface with a FT232H breakout board (AdaFruit makes a nice one). I can see the data lines and it looks like most of the logic works, more or less. It's a proof of concept port and a test for "can I tell the AI to take an Arduino sketch and port it to Python" (the answer is far more yes than it use to be).
    • That said, it's very slow (reading in at 2-3sps). I'm not sure how to optimize this, and speeding it up is not an immediate priority.

2025-06-30 15 28 38-1 2025-06-25 20 25 30

Future Plans:

Major Function Things to Address:

  • Writing to MicroSD cards over the AUX SPI Bux on the RA4M1 XIAO boards. I set this up and tested it, but it didn't work and needs to be troubleshot.
  • Getting the code to run on the XIAO RP2350 board. It compiles but does not run.

Potential Refinements To-Do List:

  • Revise the PCB design to shrink the physical size (the current design was made with hand-soldering in mind). This would involve:
    • Smaller footprint components for things like the pullup resistors.
    • Dedicated multiple transistor packages for the switching functions rather than the discreet components.
    • There are probably other ways to shrink the design.
    • There is some potential performance improvement room to the analog circuit if I take advantage of the ADS1115's max input voltage of ~6.144vdc instead of 5vdc.
  • There is always room for cleanup in the code to make it more elegant.

Ideas for Expanding on the Current Function / :

  • Make a version that uses an ADS1256 instead of the ADS1115 to support measurements speeds up to 30,000 samples/second and resolutions of up to 24bits. (I have had proof-of-concept success with this using a Raspberry PI ADS1256 hat.)
  • Make a version that runs off a Raspberry Pi.
  • Implement WiFi/Bluetooth features on the boards that support it.
  • Implement DAC output as a simple function generator for the boards that support it.
  • Add a jumper on the PCB and write the code to allow four-wire resistance readings.

If you're interested in helping develop this please feel free to reach out.

FAQ:

  • Q: What is the logic voltage?

    • A: The current PCB works for either 3.3 or 5vdc.
  • Q: Is there voltage isolation on the USB?

    • A: There is enough isolation (500K Ohms) that you will not hurt anything by measuring voltage (in either polarity) on something connected to the wall while the meter is also connected to the wall, but not enough to prevent ground loops from interfering with measurements. See the longer, full write up on my website, and then buy the Adafruit USB voltage isolation board.
  • Q: The Adafruit isolation board says "100mA." What does the meter draw?

    • A: With the XIAO RA4M1, 50-60mA typical when measuring voltage. Closer to 100mA when measuring resistance. The resistance circuit goes into low-power mode several seconds after being open (except in a no-sleep mode).
  • Q: Does it work on an Arduino Uno R3?

    • A: As a basic meter, yes, but there's no keyboard emulation.
  • Q: Can I buy one?

    • A: Eventually, yes, probably? I do not have a current timeline for bringing these to market. If you want one please reach out to me. If you want to hand-solder it yourself I can sell you a single PCB and maybe some of the components with higher individual costs.

Parts

56
QtyValueFootprintReferences
4100nF / 16VAD8237DevBoard:C_0805_2012MetricC2, C9, C10, C11
44.7kAD8237DevBoard:R_0805_2012MetricR17, R18, R19, R20
4M3 NPTHAD8237DevBoard:MountingHole_3.2mm_M3H1, H2, H3, H4
310k 0.1%AD8237DevBoard:R_0805_2012MetricR3, R15, R16
2100R 0.1%AD8237DevBoard:R_0805_2012MetricR1, R2
210nF (DNP)AD8237DevBoard:C_0805_2012MetricC3, C6
21M (DNP)AD8237DevBoard:R_0805_2012MetricR9, R10
21k 0.1%AD8237DevBoard:R_0805_2012MetricR5, R11
21nF (DNP)AD8237DevBoard:C_0805_2012MetricC4, C5
21uF / 16VAD8237DevBoard:C_0805_2012MetricC8, C12
1100RAD8237DevBoard:R_0805_2012MetricR8
1100kAD8237DevBoard:R_0805_2012MetricR7
1100k 0.1%AD8237DevBoard:R_0805_2012MetricR6
110uF / 16VAD8237DevBoard:C_0805_2012MetricC1
11M 0.1%AD8237DevBoard:R_0805_2012MetricR12
1200RAD8237DevBoard:R_0805_2012MetricR14
12kAD8237DevBoard:R_0805_2012MetricR13
1470pF C0GAD8237DevBoard:C_0805_2012MetricC7
190.9k 0.1%AD8237DevBoard:R_0805_2012MetricR4
1AD8237ARMZAD8237DevBoard:MSOP-8_3x3mm_P0.65mmU1
1ANALOG SUPPLYAD8237DevBoard:PinHeader_1x03_P2.54mm_VerticalJP1
1BW: LOW / HIGHAD8237DevBoard:PinHeader_1x03_P2.54mm_VerticalJP2
1EXT ANALOG POWERAD8237DevBoard:PinHeader_1x02_P2.54mm_VerticalJ1
1FBAD8237DevBoard:TestPoint_Pad_D1.5mmTP6
1GNDAD8237DevBoard:TestPoint_Pad_D1.5mmTP2
1I2C / LOGIC POWERAD8237DevBoard:PinHeader_1x04_P2.54mm_VerticalJ4
1I2C PULL-UPSAD8237DevBoard:PinHeader_1x02_P2.54mm_VerticalJP4
1IN_N_FAD8237DevBoard:TestPoint_Pad_D1.5mmTP4
1IN_P_FAD8237DevBoard:TestPoint_Pad_D1.5mmTP3
1OPA333AIDBVRAD8237DevBoard:SOT-23-5U4
1OUTPUT / EXT REFAD8237DevBoard:PinHeader_1x03_P2.54mm_VerticalJ3
1OUT_RAWAD8237DevBoard:TestPoint_Pad_D1.5mmTP5
1REFAD8237DevBoard:TestPoint_Pad_D1.5mmTP7
1REFERENCE SELECTAD8237DevBoard:PinHeader_2x03_P2.54mm_VerticalJP3
1SENSORAD8237DevBoard:PinHeader_1x03_P2.54mm_VerticalJ2
1TCA9536DGKRAD8237DevBoard:VSSOP-8_3x3mm_P0.65mmU3
1TMUX1104DGSAD8237DevBoard:MSOP-10_3x3mm_P0.5mmU2
1VMIDAD8237DevBoard:TestPoint_Pad_D1.5mmTP8
1VSAD8237DevBoard:TestPoint_Pad_D1.5mmTP1

More from oihdesigns/Micro-DMM

12
  • 4 layers68.5 × 53.3 mmDMM KiCAD V4 next, the printed circuit board in 3D

    DMM KiCAD V4 next

    oihdesigns/Micro-DMM

    A small, open hardware DMM

    80 parts2
  • 4 layers88.9 × 50.8 mmNametagVoltmeter, the printed circuit board in 3D

    NametagVoltmeter

    oihdesigns/Micro-DMM

    A small, open hardware DMM

    66 parts2
  • 4 layers85.5 × 47.4 mmDMM Feather Redux, the printed circuit board in 3D

    DMM Feather Redux

    oihdesigns/Micro-DMM

    A small, open hardware DMM

    61 parts2
  • 4 layers66 × 37.1 mmDualAMCBoard, the printed circuit board in 3D

    DualAMCBoard

    oihdesigns/Micro-DMM

    A small, open hardware DMM

    59 parts2
  • 4 layers68.5 × 53.3 mmDMM Feather Specific, the printed circuit board in 3D

    DMM Feather Specific

    oihdesigns/Micro-DMM

    A small, open hardware DMM

    57 parts2
  • 4 layers46 × 24.4 mmAnalogFrontEnd, the printed circuit board in 3D

    AnalogFrontEnd

    oihdesigns/Micro-DMM

    A small, open hardware DMM

    52 parts2
  • 4 layers30.4 × 61.2 mmOpenLead Headless V2, the printed circuit board in 3D

    OpenLead Headless V2

    oihdesigns/Micro-DMM

    A small, open hardware DMM

    44 parts2
  • 4 layers48.7 × 59.1 mmVoltmeterFrontEnd V2, the printed circuit board in 3D

    VoltmeterFrontEnd V2

    oihdesigns/Micro-DMM

    A small, open hardware DMM

    42 parts2
  • 4 layers25.4 × 61.8 mmBlinkyHawk V4, the printed circuit board in 3D

    BlinkyHawk V4

    oihdesigns/Micro-DMM

    A small, open hardware DMM

    41 parts2

Similar boards

  • 6 layers15.6 × 19.7 mmADC Board, the printed circuit board in 3D

    ADC Board

    esl-epfl/X-MODs

    Modular hardware platform based on the RISC-V X-HEEP family architecture developed at ESL, targeting ultra-low-power consumption and miniaturization, facilitating the creation of wearable devices for clinical trials

    74 parts3
  • 2 layers70 × 80 mmPpg panel, the printed circuit board in 3D

    Ppg panel

    nguyenhuy0426/PPG_simulator

    The PPG Signal Simulator is a portable device that generates synthetic PPG (photoplethysmography) waveforms with physiologically accurate morphology.

    70 parts2MIT
  • 2 layers70 × 45 mmCt amp rectifier 5v clean, the printed circuit board in 3D

    Ct amp rectifier 5v clean

    sutony1/windows-ai-eda-workflow

    Reproducible Windows SPICE to KiCad 10 to EasyEDA/JLCPCB workflow with Codex skills

    25 parts1MIT
  • 4 layers45 × 35 mmESPLionV1, the printed circuit board in 3D

    ESPLionV1

    Angus-McIntyre/ESPLionV1

    124 parts
  • 2 layers20.5 × 25 mmPpg watch, the printed circuit board in 3D

    Ppg watch

    harishbawin18/PCB

    This project presents the design and routing of a Photoplethysmography (PPG) based wearable watch PCB, developed using KiCad 9.0.

    39 parts
  • 4 layers160 × 100 mmMastertemp esp32, the printed circuit board in 3D

    Mastertemp esp32

    ryanbjohnson/PentairMasterTempESP32

    This folder is the KiCad project area for the MasterTemp 125 ESP32 interface board.

    95 partsMIT
  • 2 layers28 × 32 mmTransducerBLE, the printed circuit board in 3D

    TransducerBLE

    UT-yakusaku/WirelessIntestine

    This is the code for a paper titiled "Wireless Recording and Autoencoder Denoising of Intestinal Activity in Freely Moving Rats"

    24 parts
  • 4 layers21.5 × 62.8 mmIn shaft wsg mommy, the printed circuit board in 3D

    In shaft wsg mommy

    BlueJayRacing/bjr_kicad

    jhu blue jay racing daq kicad pcb files

    62 parts

Questions

How big is the AD8237DevBoard PCB?

It measures 60 × 50 mm and has 2 copper layers, 1.6 mm thick.

What parts does the AD8237DevBoard use?

56 parts, built around the AD8237ARMZ, OPA333AIDBVR-MS, TCA9536DGKR and TMUX1104DGS. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the AD8237DevBoard KiCad files?

From the oihdesigns/Micro-DMM repository on GitHub, at the commit this page was made from: the board is PCBDesigns/AD8237DevBoard/archive/pre-eight-gain/AD8237DevBoard.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the AD8237DevBoard design in my own project?

Its repository states no licence, so its author keeps all rights: ask oihdesigns before reusing the design.