
Panel daisy
ohmtech-rdi/eurorack-blocks
Software to Hardware Prototyping for Eurorack using C++, Max/Gen~ or Faust

Software to Hardware Prototyping for Eurorack using C++, Max/Gen~ or Faust
Multiplexer is an open-source printed circuit board by ohmtech-rdi, from the ohmtech-rdi/eurorack-blocks repository on GitHub. It is a 2-layer board of 22 × 19 mm with 5 parts on 14 nets, routed with 79 tracks and 10 vias.
Its parts include 2 capacitors, 2 connectors and 1 IC. It belongs with the audio and music boards and the STM32 boards of this library.
This block is a simple potentiometer and LED in a slider form factor.
It is adapted from the Mutable Instuments Stages schematics.
Pin headers don't come with just one position. Instead of that, the BOM has 2-position pin male headers that need to be broke into 2 pieces.
This block provides a silder potentiometer with a red LED.
This modules needs to be connected to the 3V3A and GND lines from the power block.
On Daisy Seed, use the 3V3 Analog Power I/O on Pin 21, not the digital power.
All GND pins are internally connected in the block.
The signal IN drives the LED. It should be connected to any GPIO of the
target MCU, preferably non-analog GPIOs.
The signal OUT is the potentiometer value. It should be connected to any Analog GPIO of the
target MCU.
When using Daisy Seed as a development platform, see its pinout for details. The Daisy Seed has a total of 31 GPIOs, only 12 of which are analog.
Gerber renders made with tracespace view.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 1 | 100n | Capacitor_SMD:C_0603_1608Metric | C2 |
| 1 | 1n | Capacitor_SMD:C_0603_1608Metric | C1 |
| 1 | 4051 | Package_SO:TSSOP-16_4.4x5mm_P0.65mm | U1 |
| 1 | BOTTOM | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J2 |
| 1 | TOP | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J3 |

ohmtech-rdi/eurorack-blocks
Software to Hardware Prototyping for Eurorack using C++, Max/Gen~ or Faust

ohmtech-rdi/eurorack-blocks
Software to Hardware Prototyping for Eurorack using C++, Max/Gen~ or Faust

ohmtech-rdi/eurorack-blocks
Software to Hardware Prototyping for Eurorack using C++, Max/Gen~ or Faust

ohmtech-rdi/eurorack-blocks
Software to Hardware Prototyping for Eurorack using C++, Max/Gen~ or Faust

ohmtech-rdi/eurorack-blocks
Software to Hardware Prototyping for Eurorack using C++, Max/Gen~ or Faust

ohmtech-rdi/eurorack-blocks
Software to Hardware Prototyping for Eurorack using C++, Max/Gen~ or Faust

ohmtech-rdi/eurorack-blocks
Software to Hardware Prototyping for Eurorack using C++, Max/Gen~ or Faust

ohmtech-rdi/eurorack-blocks
Software to Hardware Prototyping for Eurorack using C++, Max/Gen~ or Faust

ohmtech-rdi/eurorack-blocks
Software to Hardware Prototyping for Eurorack using C++, Max/Gen~ or Faust

ohmtech-rdi/eurorack-blocks
Software to Hardware Prototyping for Eurorack using C++, Max/Gen~ or Faust

ohmtech-rdi/eurorack-blocks
Software to Hardware Prototyping for Eurorack using C++, Max/Gen~ or Faust

ohmtech-rdi/eurorack-blocks
Software to Hardware Prototyping for Eurorack using C++, Max/Gen~ or Faust


joypad-ai/joypad-os
Universal controller firmware for building adapters, dongles, and custom controllers.

OLIMEX/OLINUXINO
OLINUXINO is Open Source / Open Hardware, low cost from EUR 24 Linux Industrial grade Single Board Computer capable to operate -25+85C

jamro/tiny-engineer
A small desktop robot that brings an AI coding assistant to life, physically acting out when it reads files, thinks, writes code, and finishes work.

hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!



Luos-io/luos_engine
Open-source and real-time orchestrator for cyber-physical-systems, to easily design, test and deploy embedded applications and digital twins.
It measures 22 × 19 mm and has 2 copper layers, 1.6 mm thick.
5 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the ohmtech-rdi/eurorack-blocks repository on GitHub, at the commit this page was made from: the board is blocks/multiplexer/multiplexer.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask ohmtech-rdi before reusing the design.