
Panel daisy
ohmtech-rdi/eurorack-blocks
Software to Hardware Prototyping for Eurorack using C++, Max/Gen~ or Faust

Software to Hardware Prototyping for Eurorack using C++, Max/Gen~ or Faust
Custom is an open-source printed circuit board by ohmtech-rdi, from the ohmtech-rdi/eurorack-blocks repository on GitHub. It is a 2-layer board of 59.6 × 109.5 mm with 17 parts on 43 nets, routed with 48 tracks and 0 vias.
Its parts include 3 diodes, 3 connectors, 2 capacitors, 2 inductors and 1 resistor. It belongs with the audio and music boards and the STM32 boards of this library.
This block is a simple potentiometer and LED in a slider form factor.
It is adapted from the Mutable Instuments Stages schematics.
Pin headers don't come with just one position. Instead of that, the BOM has 2-position pin male headers that need to be broke into 2 pieces.
This block provides a silder potentiometer with a red LED.
This modules needs to be connected to the 3V3A and GND lines from the power block.
On Daisy Seed, use the 3V3 Analog Power I/O on Pin 21, not the digital power.
All GND pins are internally connected in the block.
The signal IN drives the LED. It should be connected to any GPIO of the
target MCU, preferably non-analog GPIOs.
The signal OUT is the potentiometer value. It should be connected to any Analog GPIO of the
target MCU.
When using Daisy Seed as a development platform, see its pinout for details. The Daisy Seed has a total of 31 GPIOs, only 12 of which are analog.
Gerber renders made with tracespace view.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 10u | Capacitor_SMD:C_0805_2012Metric | C1, C2 |
| 2 | D_Schottky | Diode_SMD:D_SOD-123 | D1, D2 |
| 2 | Ferrite_Bead | Inductor_SMD:L_0603_1608Metric | L1, L2 |
| 2 | IN | Connector_Thonk:ThonkiconnJack | J2, J3 |
| 2 | KNURLED NUT | Empty:Empty | H3, H4 |
| 1 | 100k | Potentiometer_Thonk:AlphaPot9ShaftD | RV1 |
| 1 | 1k | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | DaisyPatchSm_Rev1 | Socket_DaisyPatchSm:DaisyPatchSm | A1 |
| 1 | ERB LOGO | Logo_Erb:ErbLog.15mm | H1 |
| 1 | LED | LED_SMD:LED_0603_1608Metric | D3 |
| 1 | POWER BUS | Connector_IDC:IDC-Header_2x05_P2.54mm_Vertical | J1 |
| 1 | ROGAN 6PS | Empty:Empty | H2 |

ohmtech-rdi/eurorack-blocks
Software to Hardware Prototyping for Eurorack using C++, Max/Gen~ or Faust

ohmtech-rdi/eurorack-blocks
Software to Hardware Prototyping for Eurorack using C++, Max/Gen~ or Faust

ohmtech-rdi/eurorack-blocks
Software to Hardware Prototyping for Eurorack using C++, Max/Gen~ or Faust

ohmtech-rdi/eurorack-blocks
Software to Hardware Prototyping for Eurorack using C++, Max/Gen~ or Faust

ohmtech-rdi/eurorack-blocks
Software to Hardware Prototyping for Eurorack using C++, Max/Gen~ or Faust

ohmtech-rdi/eurorack-blocks
Software to Hardware Prototyping for Eurorack using C++, Max/Gen~ or Faust

ohmtech-rdi/eurorack-blocks
Software to Hardware Prototyping for Eurorack using C++, Max/Gen~ or Faust

ohmtech-rdi/eurorack-blocks
Software to Hardware Prototyping for Eurorack using C++, Max/Gen~ or Faust

ohmtech-rdi/eurorack-blocks
Software to Hardware Prototyping for Eurorack using C++, Max/Gen~ or Faust

ohmtech-rdi/eurorack-blocks
Software to Hardware Prototyping for Eurorack using C++, Max/Gen~ or Faust

ohmtech-rdi/eurorack-blocks
Software to Hardware Prototyping for Eurorack using C++, Max/Gen~ or Faust

ohmtech-rdi/eurorack-blocks
Software to Hardware Prototyping for Eurorack using C++, Max/Gen~ or Faust



hoglet67/RGBtoHDMI
Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI


hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

DDeGonge/OS-ARM
This arm is not industrial and it will not be fast, but that is not my goal. But it will hopefully be a very nice looking arm fully capable of 6dof motion, cheap enough to keep it accessable but capable enough to…


It measures 59.6 × 109.5 mm and has 2 copper layers, 1.6 mm thick.
17 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the ohmtech-rdi/eurorack-blocks repository on GitHub, at the commit this page was made from: the board is samples/custom/artifacts/hardware/Custom.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask ohmtech-rdi before reusing the design.