Skip to the content
4 layers22 × 48.4 mmTracer, the printed circuit board in 3D

Tracer -- A module for simulating conductive ink PCB traces

Size
22 × 48.4 mm
Copper layers
4
Thickness
1 mm
Parts
21
Nets
25
Pads
112
Tracks, vias
390, 44
Pours
5
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
20 May 2021
Updated
15 Jun 2021

Overview

Tracer is an open-source printed circuit board by NovaCentrix, from the NovaCentrix/chris-tracer-pcb repository on GitHub. It is a 4-layer board of 22 × 48.4 mm with 21 parts on 25 nets, routed with 390 tracks and 44 vias.

It is built around the AD8403ARZ1, TXS0101DBV and 1N4148W, with the B3U-3100P-B and MMBT3904 among its other parts. Its parts include 4 resistors, 4 switches, 3 ICs, 2 diodes and 2 transistors.

Main components

5

README

readme.md

The TraceR

A Module for Simulating Conductive Ink PCB Traces

Revisions

Version 2

  • Digipot power supply from from 3.3 to 5, in order to reduce the wiper resistance further (see the datasheet). This means the addition of level translator for the MISO signal into the MCU.

  • The digipot SDO pin is open drain. Added pullup resistors on each one.

  • Assembly of modules onto v1 board was difficult. And the whole assembly needs to be thinner so two modules can be installed adjacent to each other (relates to the pin header spacing on the main board). Gave up on the idea of avoiding a board cutout. Re-routing of signals, and made the board just slightly larger (mostly taller) to allow for the required cutout.

  • Changed PCB thickness from 1.6 to 1.0 mm.

  • Found some tiny buttons (about the same size as those on the Tiny 2040 module) and put them at the top corners. This will allow the user to change resistance values without using the serial port.

Version 1

First release.

Observations

Before I forget, here are some thoughts to consider if there ever is going to be a version 3.

  • Make D1/D2 larger, since that package is nearly impossible to hand solder. Or...

  • Make the transistor and resistor packages smaller and reflow rather than hand solder. Also, Digipots are available in a smaller package:

    • TSSOP-24 package 7.8 x 4.4 mm
    • SOIC-24W 15.4 x 7.5 mm (currently used)
  • Look carefully at the Adafruit Qt Py RP2040 module. It looks smaller, has a smaller and well-defined required cutout and mechanical drawings. Fewer pins.

  • Save even more space my tossing the module concept and building the RP2040 board and the OLED module directly on the TraceR's PCB.

Parts

21
QtyValueFootprintReferences
41K.tracer:R_0805_2012MetricR1, R2, R3, R4
21N4148W.tracer:DFN1006-2D1, D2
2AD8403ARZ1.tracer:SOIC-24W_7.5x15.4mm_P1.27mmU1, U2
2B3U-3100P-B.tracer:SW_B3U-3100P-BS1, S2
2Coto-9913-05-20.tracer:REED_RELAY_COTO_9913K1, K2
2MMBT3904.tracer:SOT-23Q1, Q2
2TestPoint.tracer:via-0.8x0.4TP13, TP14
1ASSY_OLED_490MILS_62x32_I2C.tracer:MODULE_OLED_490_SMALL_PADSA2
1IO_JACK_F04_SPLIT.tracer:SAMTEC-SSQ-102-02-SIDEWAYSJ1
1Logo_Open_Hardware_Small.tracer:OSHW-Logo2_7.3x6mm_SilkScreenLOGO1
1TXS0101.tracer:SOT-23-6U3
1Tiny2040.tracer:MODULE_TINY_2040_DEV2A1

Similar boards

  • 2 layers80.1 × 107.1 mmHiro, the printed circuit board in 3D

    Hiro

    Broseph9972/H.I.R.O-MDS-0027

    a real mp3 player based on the H.I.R.O from good kid music videos.

    18 parts1GPL-3.0
  • 2 layers391 × 131.1 mmAustin, the printed circuit board in 3D

    Austin

    AcheronProject/Austin

    Austin PCB

    599 parts18
  • 2 layers347.7 × 123.8 mm87keyboard, the printed circuit board in 3D

    87keyboard

    danielpclin/87keyboard

    87 keys keyboard - Uno

    420 parts
  • 4 layers60 × 45 mmHotplate, the printed circuit board in 3D

    Hotplate

    Keyaan-07/Hotplate

    Check out the Project's files on KiCanvas(PCB and Heating element) and Onshape!

    85 partsMIT
  • 2 layers391 × 131.2 mmAustin, the printed circuit board in 3D

    Austin

    kitspace-test-repos/kicad6-file-collection

    558 partsMIT
  • 2 layers101.5 × 105.4 mmPico cart snes, the printed circuit board in 3D

    Pico cart snes

    alttpo/pico-cart-snes

    Raspberry Pi Pico SNES flash cart (no SD card, WIP)

    62 parts13MIT
  • 4 layers62.9 × 88.6 mmBit block, the printed circuit board in 3D

    Bit block

    Citrullin/Sovereign_Bunny_Stack

    From web 3 unicorn fantasy to federated web 2.5 reality.

    169 parts4
  • 2 layers62.2 × 35.6 mmESP8285-WLED, the printed circuit board in 3D

    ESP8285-WLED

    c-/ESP8285-WLED

    ESP8285 WLED PCB

    58 parts3

Questions

How big is the Tracer PCB?

It measures 22 × 48.4 mm and has 4 copper layers, 1 mm thick.

What parts does the Tracer use?

21 parts, built around the AD8403ARZ1, TXS0101DBV, 1N4148W and B3U-3100P-B. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Tracer KiCad files?

From the NovaCentrix/chris-tracer-pcb repository on GitHub, at the commit this page was made from: the board is tracer.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Tracer design in my own project?

Its repository states no licence, so its author keeps all rights: ask NovaCentrix before reusing the design.