Skip to the content
2 layers51 × 30.5 mmLED Blinker, the printed circuit board in 3D

LED blinker PCB built around the 555 timer IC in astable mode, with documentation, simulation models and supporting files.

Size
51 × 30.5 mm
Copper layers
2
Thickness
1.6 mm
Parts
9
Nets
7
Pads
24
Tracks, vias
54, 5
Pours
1
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
14 Sep 2026
Updated
11 Oct 2026

Overview

LED Blinker is an open-source printed circuit board by nizarbadriali, from the nizarbadriali/Blinking-LED-Documentation repository on GitHub, published under the MIT licence. It is a 2-layer board of 51 × 30.5 mm with 9 parts on 7 nets, routed with 54 tracks and 5 vias.

Its parts include 3 capacitors, 3 resistors, 1 IC, 1 diode and 1 connector.

README

README.md

LED Blinker PCB — 555 Astable Timer Circuit

Status: Schematic and PCB layout designed in KiCad. SPICE simulation, ERC/DRC results, manufacturing export, assembly, and bench testing are not yet documented here. Timing figures below are calculated from the standard 555 astable equations, not measured.

LED blinker schematic

PCB layout

PCB 3D render

What This Is

A free-running LED blinker built around an ICM7555xP (CMOS 555 timer) wired as an astable oscillator. R1, R2 and C1 set the blink rate; the timer output (pin 3) drives a red LED through a 330 Ω current-limiting resistor. It is the follow-up to the LED-PCB-Documentation project, adding an active timing circuit to the simple resistor + LED design.

How the Circuit Works

BlockPartsRole
TimerU1 (ICM7555xP)Astable oscillator. RST (pin 4) is tied to VCC so the timer always runs.
Timing networkR1 (10 kΩ), R2 (470 kΩ), C1 (10 µF)C1 charges through R1 + R2 and discharges through R2 via DISCH (pin 7). THRES and TRIG (pins 6 and 2) are tied together on the C1 node.
Control-voltage bypassC2 (100 nF)CONT (pin 5) to GND, keeps the internal threshold reference quiet.
Supply decouplingC3 (100 nF)VCC to GND near the timer.
Output stageR3 (330 Ω), D1 (LED)Pin 3 → R3 → D1 → GND.
Power inputJ1 (2-pin header)Pin 1 = VCC, pin 2 = GND.

Results

ParameterValueEvidence or qualification
Output high time≈ 3.33 sCalculated: 0.693 × (R1 + R2) × C1, nominal values
Output low time≈ 3.26 sCalculated: 0.693 × R2 × C1, nominal values
Period / frequency≈ 6.6 s / ≈ 0.15 HzCalculated: 1.44 / ((R1 + 2·R2) × C1)
Duty cycle≈ 50.5 %Calculated: (R1 + R2) / (R1 + 2·R2)
LED currentpendingDepends on supply voltage and LED forward voltage; to be simulated and measured
ERC / DRC / paritypendingResults not yet uploaded
Manufacturing packagependingGerbers and drills not yet exported

Real timing will differ from these numbers: a 10 µF electrolytic commonly has a −20 %/+20 % or wider tolerance, and resistor tolerance adds to that. Treat the figures as a prediction until measured with a stopwatch or scope.

Quick Start

View the design: Open the .kicad_pro file in the kicad/ folder in KiCad, then open the schematic and PCB from the project manager.

Run the simulation: (pending) Add the LTspice circuit to simulation/ltspice/ and describe how to run the transient analysis here.

Bill of Materials

ReferenceValuePackage / specificationSelection status
U1ICM7555xP8-pin DIPConfirm supply range and output drive in the datasheet; part number pending
R110 kΩAxial through-holeTolerance and part number pending
R2470 kΩAxial through-holeTolerance and part number pending
R3330 ΩAxial through-holeTolerance and part number pending
C110 µFRadial electrolytic; polarised (+ toward the R2 / pin 2 / pin 6 node)Voltage rating and part number pending
C2100 nFThrough-hole ceramicVoltage rating and part number pending
C3100 nFThrough-hole ceramicVoltage rating and part number pending
D1LED5 mm through-holeColour, part number, polarity marking, and ratings pending
J12-pin header2.54 mm pitch; pin 1 = VCC, pin 2 = GNDManufacturer part number pending

Project Files

PathContents
kicad/Project, schematic, PCB, screenshots, and manufacturing ZIP (to be added)
simulation/Simulation files
models/LED and timer model directives
workdir/Supporting data
DESIGN_NOTES.mdDesign decisions, revisions, checks, and fabrication details (to be written)

Limitations and Next Steps

  • Add the supply voltage this board is designed for, and confirm it is within the ICM7555 and LED ratings.
  • Run ERC, DRC, and schematic-to-PCB parity checks and upload the results.
  • Simulate the astable timing and LED current, then compare against the calculated values above.
  • Select real part numbers and check datasheets against the footprints.
  • Assemble, measure the blink period, and compare with prediction before claiming physical validation.

Tools and Attribution

  • KiCad: schematic and PCB design (record the exact version from the project files).
  • ICM7555 datasheet: reference for the astable timing equations and pin functions.

License

MIT License. See LICENSE.

Parts

9
QtyValueFootprintReferences
2100nFCapacitor_THT:C_Disc_D5.0mm_W2.5mm_P2.50mmC2, C3
110kΩResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR1
110µFCapacitor_THT:CP_Radial_D5.0mm_P2.00mmC1
1330ΩResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR3
1470kΩResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR2
1Conn_01x02_MountingPinConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ1
1ICM7555xPPackage_DIP:DIP-8_W7.62mmU1
1LEDLED_THT:LED_D5.0mmD1

Similar boards

  • 2 layers103 × 30.5 mmTS Back Endcap, the printed circuit board in 3D

    TS Back Endcap

    EEVengers/ThunderScope

    ThunderScope GitHub Repo

    9 parts1.3kMIT
  • 2 layers31.8 × 47.6 mmNGC 38 connector, the printed circuit board in 3D

    NGC 38 connector

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    9 parts1.2k
  • 2 layers24 × 27.3 mmExpansion Card Retrofit, the printed circuit board in 3D

    Expansion Card Retrofit

    FrameworkComputer/ExpansionCards

    Reference designs and documentation to create Expansion Cards for the Framework Laptop

    9 parts1.1kCC-BY-4.0
  • 2 layers15.6 × 17.3 mmSKR Mini TFT Thermistor Board, the printed circuit board in 3D

    SKR Mini TFT Thermistor Board

    VoronDesign/Voron-Hardware

    Cool Hardware designed by the Voron Design group

    9 parts1.1kGPL-3.0
  • 2 layers39.1 × 49.5 mmLearnoliver, the printed circuit board in 3D

    Learnoliver

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    9 parts915
  • 2 layers17.4 × 16.9 mmToolhead, the printed circuit board in 3D

    Toolhead

    tanaes/whopping_Voron_mods

    9 parts787GPL-3.0
  • 2 layers9.8 × 108 mmExpander, the printed circuit board in 3D

    Expander

    wntrblm/Castor_and_Pollux

    A Juno-inspired dual oscillator

    9 parts587
  • 2 layersKeyboard after, the printed circuit board in 3D

    Keyboard after

    adamws/kicad-kbplacer

    KiCad plugin for automatic keyboard's key placement and routing

    9 parts547GPL-3.0

Questions

How big is the LED Blinker PCB?

It measures 51 × 30.5 mm and has 2 copper layers, 1.6 mm thick.

What parts does the LED Blinker use?

9 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the LED Blinker KiCad files?

From the nizarbadriali/Blinking-LED-Documentation repository on GitHub, at the commit this page was made from: the board is kicad/LED_Blinker.kicad_pcb and its schematic kicad/LED_Blinker.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the LED Blinker design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).