Skip to the content
2 layers102 × 42 mmProject Parallel Circuit, the printed circuit board in 3D

Project Parallel Circuit

Nikolov999/Project-Parallel-Circuit

Created my first parallel circuit with dual LEDs.

Size
102 × 42 mm
Copper layers
2
Thickness
1.6 mm
Parts
5
Nets
4
Pads
10
Tracks, vias
20, 0
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
2 Oct 2026
Updated
2 Oct 2026

Overview

Project Parallel Circuit is an open-source printed circuit board by Nikolov999, from the Nikolov999/Project-Parallel-Circuit repository on GitHub. It is a 2-layer board of 102 × 42 mm with 5 parts on 4 nets, routed with 20 tracks and 0 vias.

Its parts include 2 resistors, 2 diodes and 1 connector.

README

README.md

Project-Parallel-Circuit

A first hands-on KiCad PCB project built to explore a real parallel DC circuit from electrical calculation through schematic capture, footprint assignment, PCB layout, routing, verification, and 3D inspection.

The board uses a 5 V input and two independent LED branches. Each branch contains its own 330 Ω current-limiting resistor and LED, so the resistor/LED pair is series-connected inside the branch while the two complete branches are connected in parallel.

3D PCB view

Circuit architecture

text
                     Branch 1
              R1 330 Ω        D1
          +---/\/\/\/---------|>|---+
          |                         |
+5 V -----+                         +----- GND
          |                         |
          +---/\/\/\/---------|>|---+
              R2 330 Ω        D2
                     Branch 2

Electrical structure:

  • J1 pin 1: +5 V input
  • J1 pin 2: GND
  • Branch 1: +5 V -> R1 -> D1 -> GND
  • Branch 2: +5 V -> R2 -> D2 -> GND
  • R1 and D1 are in series.
  • R2 and D2 are in series.
  • The two branches are in parallel.

Electrical calculations

Design assumptions:

  • Supply voltage, Vs = 5 V
  • Approximate LED forward voltage, Vf = 2 V
  • Current-limiting resistance per branch = 330 Ω

Voltage across each resistor:

text
Vr = Vs - Vf
Vr = 5 V - 2 V
Vr = 3 V

Approximate branch current:

text
I = Vr / R
I = 3 V / 330 Ω
I ≈ 0.00909 A
I ≈ 9.1 mA

Because the branches are parallel and use the same nominal component values:

text
I1 ≈ 9.1 mA
I2 ≈ 9.1 mA
Itotal = I1 + I2
Itotal ≈ 18.2 mA

Approximate resistor dissipation:

text
P = Vr × I
P ≈ 3 V × 0.00909 A
P ≈ 0.027 W

A 0.25 W resistor rating therefore provides substantial margin for the assumed operating point.

Vf = 2 V is a design approximation. Real LED forward voltage varies with LED type, colour, current, temperature, and manufacturing tolerance, so measured current will differ somewhat from the calculated value.

Schematic

KiCad schematic

The schematic was built with two independent current-limited LED branches tied between the same +5 V and GND nodes. Power flags are used so KiCad's electrical rules checker understands that the rails are driven from an external source through J1.

PCB layout

PCB layout

The board is intentionally spacious so the two branches are visually obvious. The current revision uses:

  • Board outline: 102 mm × 42 mm
  • Board thickness setting: 1.6 mm
  • Routing layer: F.Cu
  • Track width: 0.20 mm
  • Vias: none
  • Through-hole components throughout

3D views

3D PCB front view

3D PCB alternate angle

Components

ReferenceQtyValue / PartFootprint
J111×02 connectorPinHeader_1x02_P2.54mm_Vertical
R1, R22330 Ω resistorR_Axial_DIN0207_L6.3mm_D2.5mm_P2.54mm_Vertical
D1, D225 mm LEDLED_D5.0mm

A machine-readable version is available in BOM.csv.

Design verification

Final checks completed in KiCad:

  • Electrical Rules Checker reviewed
  • Design Rules Checker reviewed
  • Unconnected items cleared
  • PCB / schematic parity checked
  • LED polarity corrected and verified
  • 3D board inspection completed

Repository structure

text
Project-Parallel-Circuit/
├── README.md
├── BOM.csv
├── .gitignore
├── .gitattributes
├── kicad/
│   ├── Project-Parallel-Circuit.kicad_pro
│   ├── Project-Parallel-Circuit.kicad_sch
│   └── Project-Parallel-Circuit.kicad_pcb
├── docs/
│   ├── board-definition.md
│   ├── calculations.md
│   ├── design-notes.md
│   └── source-notes/
│       ├── Board-Definition-original.txt
│       └── Calculating-Branches-original.txt
├── images/
│   ├── schematic.png
│   ├── pcb-layout.png
│   ├── pcb-3d-front.png
│   └── pcb-3d-angle.png
└── fabrication/
    ├── README.md
    ├── Project-Parallel-Circuit-Gerbers.zip

What this project demonstrates

  • Ohm's law
  • Kirchhoff's Current Law
  • Kirchhoff's Voltage Law
  • Series elements inside parallel branches
  • Independent LED current limiting
  • LED polarity and anode/cathode mapping
  • KiCad schematic capture
  • ERC workflow
  • Footprint assignment
  • PCB placement and routing
  • Board outlines with Edge.Cuts
  • Silkscreen labeling
  • DRC and schematic/PCB parity checks
  • 3D mechanical inspection

Software

Designed with KiCad 10.

Fabrication outputs

The repository includes the final Gerber job, separate manufacturing layers, plated/non-plated Excellon drill files, and a ready-to-upload manufacturing ZIP. The corrected export keeps Plot on All Layers empty so copper and silkscreen are not duplicated into unrelated manufacturing layers.

Basic checks performed on this export:

  • Edge_Cuts contains only the closed 102 mm × 42 mm board profile.
  • F.Cu contains the front routing and through-hole pads.
  • B.Cu contains through-hole pad copper without copied front routing.
  • Project-Parallel-Circuit-PTH.drl contains 10 plated component holes.
  • Project-Parallel-Circuit-NPTH.drl is empty because the board has no NPTH mechanical holes.

See fabrication/README.md for the file set.

Parts

5
QtyValueFootprintReferences
2330RResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P2.54mm_VerticalR1, R2
2LEDLED_THT:LED_D5.0mmD1, D2
1Conn_01x02Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ1

Similar boards

  • 2 layers98 × 27 mmXy limit, the printed circuit board in 3D

    Xy limit

    opulo-inc/lumenpnp

    The LumenPnP is an open source pick and place machine.

    5 parts3.7k
  • 2 layers21 × 33 mm24g2usb pico2w, the printed circuit board in 3D

    24g2usb pico2w

    joypad-ai/joypad-os

    Universal controller firmware for building adapters, dongles, and custom controllers.

    5 parts1.7kApache-2.0
  • 2 layers53.2 × 59.6 mmA10 OLinuXino Lime Rev B SHIELD TEMPLATE, the printed circuit board in 3D

    A10 OLinuXino Lime Rev B SHIELD TEMPLATE

    OLIMEX/OLINUXINO

    OLINUXINO is Open Source / Open Hardware, low cost from EUR 24 Linux Industrial grade Single Board Computer capable to operate -25+85C

    5 parts1.5k
  • 2 layers30 × 11 mmMain control board servo tester, the printed circuit board in 3D

    Main control board servo tester

    jamro/tiny-engineer

    A small desktop robot that brings an AI coding assistant to life, physically acting out when it reads files, thinks, writes code, and finishes work.

    5 parts1.1k
  • 2 layers78.8 × 35.3 mmKiCadTest, the printed circuit board in 3D

    KiCadTest

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    5 parts915
  • 2 layers50 × 23 mmMiniCircuits LTCC, the printed circuit board in 3D

    MiniCircuits LTCC

    VanceVagell/kv4p-ht

    Open source handheld ham radio project KV4P-HT

    5 parts828GPL-3.0
  • 2 layers20.3 × 15.2 mmL0 light sensor, the printed circuit board in 3D

    L0 light sensor

    Luos-io/luos_engine

    Open-source and real-time orchestrator for cyber-physical-systems, to easily design, test and deploy embedded applications and digital twins.

    5 parts546MIT

Questions

How big is the Project Parallel Circuit PCB?

It measures 102 × 42 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Project Parallel Circuit use?

5 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Project Parallel Circuit KiCad files?

From the Nikolov999/Project-Parallel-Circuit repository on GitHub, at the commit this page was made from: the board is kicad/Project-Parallel-Circuit.kicad_pcb and its schematic kicad/Project-Parallel-Circuit.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Project Parallel Circuit design in my own project?

Its repository states no licence, so its author keeps all rights: ask Nikolov999 before reusing the design.