

Esp32 stepper driver
a low cost 3d lidar based on ydlidar-x4
- Size
- 58.4 × 80.6 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 80
- Nets
- 74
- Pads
- 343
- Tracks, vias
- 871, 108
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 2 May 2020
- Updated
- 10 Apr 2021
Overview
Esp32 stepper driver is an open-source printed circuit board by nikisalli, from the nikisalli/nik-lidar repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 58.4 × 80.6 mm with 80 parts on 74 nets, routed with 871 tracks and 108 vias.
It is built around the ESP32-S3, CH340G and LM2596S-5.0, with the PCF8574T and AMS1117-3.3 among its other parts. Its parts include 23 capacitors, 21 resistors, 14 connectors, 4 ICs and 4 diodes. It belongs with the robots and motor control boards and the ESP32 boards of this library.
Main components
5ESP32-S3
QFN-56-EP(7x7)-40℃~+105℃ -98.4dBm 150Mbps 2.412GHz~2.484GHz 2.4GHz 21dBm 340mA 3V~3.6V 88mA SPI、USB、UART、ADC、I2C、I2S、PWM WiFi transceiver QFN-56-EP(7x7) RF Transceiver ICs ROHSEspressif SystemsRF Transceiver ICsCH340G
SOP-16-40℃~+85℃ 2Mbps 3.3V、5V USB 2.0 USB to UART SOP-16 USB Converters ROHSWCH (Nanjing Qinheng Microelectronics)USB ConvertersLM2596S-5.0
TO-263-5-40℃~+125℃@(TJ) 1 150kHz 3A 4.5V~40V 5V 5mA Buck Buck Built-in Fixed No TO-263-5 DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersPCF8574T
SOP-16-300mil-40℃~+85℃ 100kHz 10uA 2.5V~6V 25mA 300uA 8 8 Cascading and address extension、Built-in LED driver I2C Interrupt Output Open-drain SOP-16-300mil I/O Expanders ROHSHGSEMII/O ExpandersAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
README
README.mdnik-lidar
a low cost 3d printed 3d lidar based on ydlidar-x4, esp32 and cheap parts!
- project status: complete, needs cleanup
info
In this repo you can find all what's necessary to assemble your own 3d lidar able to make acceptable quality 360° 3d scans
feel free to contribute since I don't have time to clean up this project
images and results

Parts
80| Qty | Value | Footprint | References |
|---|---|---|---|
| 12 | 1k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R1, R2, R3, R6, R8, R9, R15, R16, R17, R18, R19, R21 |
| 8 | 0.1u | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C3, C8, C9, C12, C13, C17, C19, C20 |
| 8 | 100n | Capacitor_SMD:C_0603_1608Metric | C2, C6, C14, C15, C16, C22, C23, C24 |
| 5 | Conn_01x04_Female | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J4, J6, J9, J11, J13 |
| 4 | 10u | Capacitor_SMD:C_1206_3216Metric_Pad1.42x1.75mm_HandSolder | C4, C11, C18, C21 |
| 4 | Conn_02x03_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J2, J5, J10, J12 |
| 4 | MountingHole | MountingHole:MountingHole_3.2mm_M3_DIN965_Pad | MH1, MH2, MH3, MH4 |
| 4 | Pololu_Breakout_A4988 | nik_things:a4988 | A1, A2, A3, A4 |
| 3 | LED | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D1, D2, D3 |
| 2 | 10k | Resistor_SMD:R_0603_1608Metric | R11, R13 |
| 2 | 12k | Resistor_SMD:R_0603_1608Metric | R4, R5 |
| 2 | 1k | Resistor_SMD:R_0603_1608Metric | R7, R10 |
| 2 | 2N7002 | Package_TO_SOT_SMD:SOT-23 | Q1, Q2 |
| 2 | SW_Push | Button_Switch_SMD:SW_SPST_SKQG_WithoutStem | SW1, SW2 |
| 1 | 1.5k | Resistor_SMD:R_0603_1608Metric | R12 |
| 1 | 10k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R20 |
| 1 | 10u | Capacitor_SMD:C_1206_3216Metric | C7 |
| 1 | 1N5819 | Diode_SMD:D_SOD-123 | D4 |
| 1 | 1u | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C10 |
| 1 | 20k | Resistor_SMD:R_0603_1608Metric | R14 |
| 1 | 220uF | Capacitor_SMD:C_Elec_6.3x7.7 | C25 |
| 1 | 33uH | Inductor_SMD:L_12x12mm_H8mm | L1 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U3 |
| 1 | Barrel_Jack | Connector_BarrelJack:BarrelJack_Horizontal | J3 |
| 1 | CH340G | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U1 |
| 1 | Conn_01x02_Female | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J8 |
| 1 | Conn_01x03_Female | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J7 |
| 1 | ESP-32S | Z_ESP32:ESP-32S | M1 |
| 1 | LM2596S-5 | Package_TO_SOT_SMD:TO-263-5_TabPin3 | U5 |
| 1 | Micro_SD_Card | nik_things:Conn_uSDcard | J14 |
| 1 | PCF8574 | Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm | U4 |
| 1 | USB_B_Micro | Connector_USB:USB_Micro-B_Molex_47346-0001 | J1 |
Similar boards
- 2 layers87 × 47 mm

- 2 layers

Drone controller
C-monC/Drone-simluation
Experimenting with reinforcement learning for drone control.
12 parts - 2 layers67.3 × 99.7 mm

- 2 layers155 × 60 mm

- 2 layers112.1 × 88.3 mm

- 2 layers140 × 100 mm

- 2 layers124 × 40 mm

RedFIS
tothpetiszilard/a3_8p_redFIS
Hacking into Audi A3 8P Driver Information System
77 parts15AGPL-3.0 - 2 layers145 × 60.3 mm

Mkulima hardware
Kazenzi/The-robotic-farmer
Click the Youtube Thumbnail below for a youtube demo video:
147 parts1MIT
Questions
How big is the Esp32 stepper driver PCB?
It measures 58.4 × 80.6 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Esp32 stepper driver use?
80 parts, built around the ESP32-S3, CH340G, LM2596S-5.0 and PCF8574T. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Esp32 stepper driver KiCad files?
From the nikisalli/nik-lidar repository on GitHub, at the commit this page was made from: the board is hardware/lidar_driver_board/esp32_stepper_driver.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Esp32 stepper driver design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).