

PoE FanController
A PoE 802.3at (25.5 W) powered quad-fan controller using the Waveshare ESP32-P4-ETH development board (SKU 32086) mounted HAT-style on a custom carrier PCB.
- Size
- 95 × 79 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 39
- Nets
- 42
- Pads
- 123
- Tracks, vias
- 240, 0
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 6 Jun 2026
- Updated
- 17 Jun 2026
Overview
PoE FanController is an open-source printed circuit board by nielsverhoeven, from the nielsverhoeven/PoE-FanController repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 95 × 79 mm with 39 parts on 42 nets, routed with 240 tracks and 0 vias.
It is built around the DHT11. Its parts include 17 resistors, 7 diodes, 6 connectors, 1 capacitor and 1 IC. It belongs with the interfaces and adapters boards and the ESP32 and RISC-V boards of this library.
Main components
1README
README.mdPoE-FanController
A PoE 802.3at (25.5 W) powered quad-fan controller using the Waveshare ESP32-P4-ETH development board (SKU 32086) mounted HAT-style on a custom carrier PCB. The carrier handles PoE power extraction and 12 V fan outputs; the Waveshare module integrates the ESP32-P4NRW32 SoC, LAN8720A Ethernet PHY (RMII), CH343P USB-UART bridge, USB-C connector, and 32 MB flash + 32 MB PSRAM. Provides wired Ethernet for reliable data-centre and server-room deployments.
Key components
| Ref | Part | Function |
|---|---|---|
| — | Waveshare ESP32-P4-ETH (SKU 32086) | MCU module — ESP32-P4NRW32 dual-core RISC-V 400 MHz, LAN8720A PHY, CH343P USB bridge, 32 MB flash, 32 MB PSRAM |
| J8 | Sullins PREC020DAAN-RC / Würth 61304021821 | 2×20 HAT header — carrier PCB ↔ Waveshare module |
| U1 | Ag9905M (Silvertel) | PoE+ PD module — 802.3at Class 4, 12 V isolated output |
| U2 | LM2596S-5.0/NOPB (TI) | Buck regulator — 12 V → 5 V, 3 A |
| D2 | 1N5822 | USB back-feed protection Schottky — prevents back-feeding PC USB host when Waveshare is programmed via USB-C while PoE is live |
| J1 | Würth 615008144521 | Shielded RJ45 — PoE power input only; MDI secondary NC |
Features
- 4 × 12 V PWM fan channels (25 kHz), GPIO4–7
- 4 × tachometer inputs (IRAM_ATTR ISR), GPIO8–11
- NTC thermistor ADC (GPIO16, 12-bit)
- HTTP OTA firmware update via POST
/api/v1/ota - Wired Ethernet via Waveshare's built-in LAN8720A (ETH.begin() / RMII)
- PoE 802.3at Class 4 power budget: ~18.9 W consumed; ~1.1 W margin against 20 W cap
- Programming and debug via Waveshare's USB-C connector (CH343P USB-UART bridge)
Power supply
J1 RJ45 (PoE power only, MDI secondary NC)
→ U1 Ag9905M → +12 V
→ J2–J5 fan headers (12 V)
→ U2 LM2596S-5.0 → +5 V → D2 (back-feed) → +5V_HAT (~4.65 V)
→ J8 (2×20 HAT header) → Waveshare ESP32-P4-ETH
→ (internal Waveshare 3.3 V LDO) → +3V3 via J8 → TACH pull-ups, NTC dividerPSE note: The PoE switch port connected to J1 must be set to "force PoE" mode (power regardless of link state), because J1's MDI secondary is NC and no 802.3 Ethernet link is visible on that port. Ethernet data connectivity is provided by the Waveshare board's own built-in RJ45 on a separate cable.
Parts
39| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | LED_GREEN | LED_THT:LED_D3.0mm | D2, D3, D4, D5, LED1, LED6 |
| 4 | 0R | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R2, R4, R16, R17 |
| 4 | 10k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R5, R6, R7, R8 |
| 4 | 150R | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R9, R10, R11, R12 |
| 3 | 330R | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R3, R13, R15 |
| 2 | 4k7 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R14 |
| 1 | 0.1uF | Capacitor_THT:C_Disc_D5.0mm_W2.5mm_P5.00mm | C1 |
| 1 | DC-Boost-Module | Custom:DC-Boost-Module | U_BOOST1 |
| 1 | DHT11 | Sensor:Aosong_DHT11_5.5x12.0_P2.54mm | U1 |
| 1 | FAN1 | Connector_Molex:Molex_KK-254_AE-6410-04A_1x04_P2.54mm_Vertical | J2 |
| 1 | FAN2 | Connector_Molex:Molex_KK-254_AE-6410-04A_1x04_P2.54mm_Vertical | J3 |
| 1 | FAN3 | Connector_Molex:Molex_KK-254_AE-6410-04A_1x04_P2.54mm_Vertical | J4 |
| 1 | FAN4 | Connector_Molex:Molex_KK-254_AE-6410-04A_1x04_P2.54mm_Vertical | J5 |
| 1 | JST 3pin | Connector_JST:JST_EH_B3B-EH-A_1x03_P2.50mm_Vertical | J6 |
| 1 | LED_ORANGE | LED_THT:LED_D3.0mm | LED2 |
| 1 | Waveshare_ESP32P4POEETH | Custom:ESP32-P4-PoE-ETH-PinSocket | J8 |
The 33 most common of 39 parts.
Similar boards
- 2 layers96.6 × 82.8 mm

- 2 layers100 × 50 mm

Conveyor belt pcb
lansidev/conveyor-belt
Miniature 3D printed conveyor belt for simulation and fun working with sensors, all controllable with Raspberry Pi
22 parts9MIT - 2 layers93 × 20 mm

- 2 layers

OpenMQTTGatewayPCB
ebrithiljonas/OMG_PCB
All in One PCB for the OpenMQTTGateway Project
36 parts7GPL-3.0 - 2 layers62 × 19.3 mm

SniffingTrinket
GeorgK/SniffingTrinket
A room climate monitor using the Adafruit Trinket Pro
23 parts6GPL-3.0 - 2 layers

Arduino relay
bhaskar9980/Guardian
Guardian is an advanced, fully automated hydroponics system designed to optimize plant growth and maximize yield.
58 parts5MIT - 2 layers100 × 43.5 mm

Firefly
Twistx77/Firefly
Open WIFI-enabled RGB lamp with temperature, humidity, suspended air particles and eCO2 sensors.
33 parts5GPL-3.0 - 2 layers30.5 × 77.5 mm

Proyecto sensor temperatura
unla-investigacion-desarrollo/ecosistema-iot
Antes de desarrollar el sistema final, realizamos una etapa de exploración donde investigamos y experimentamos con las siguientes tecnologías:
8 parts5
Questions
How big is the PoE FanController PCB?
It measures 95 × 79 mm and has 2 copper layers, 1.6 mm thick.
What parts does the PoE FanController use?
39 parts, built around the DHT11. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the PoE FanController KiCad files?
From the nielsverhoeven/PoE-FanController repository on GitHub, at the commit this page was made from: the board is hardware/kicad/PoE-FanController.kicad_pcb and its schematic hardware/kicad/PoE-FanController.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the PoE FanController design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).