Skip to the content
2 layers145.2 × 116.5 mmKeyboard pcb, the printed circuit board in 3D

Note that codelayer and btlayer in stealth.keymap currently use plain US &kp codes (e.g. &kp ATSIGN) rather than the DE macros, so those two layers assume a US layout and won't produce the labeled character under a…

Size
145.2 × 116.5 mm
Copper layers
2
Thickness
1.6 mm
Parts
74
Nets
73
Pads
659
Tracks, vias
1,140, 75
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
11 Nov 2024
Updated
22 Sep 2026

Overview

Keyboard pcb is an open-source printed circuit board by Neil-Reichlin, from the Neil-Reichlin/Stealth repository on GitHub. It is a 2-layer board of 145.2 × 116.5 mm with 74 parts on 73 nets, routed with 1,140 tracks and 75 vias.

Its parts include 27 diodes and 27 switches. It belongs with the keyboards and input boards of this library.

README

README.md

.github/workflows/build.yml

Stealth

Stealth is a fully custom-built ergonomic split keyboard. This repository provides the adapted ZMK firmware.

Image20241230111320

Usage

ZMK provides US keycodes by default, and firmware/config is written in terms of them. This keyboard's default layer instead uses the Swiss German character macros defined in include/locale/keys_de_swiss.h (the DE_* codes below), which only produce the correct character when your OS's keyboard layout is set to Swiss German - each macro sends the raw physical-key code for wherever that character sits on a real Swiss keyboard, and it's your OS's layout setting that turns that into the right character. If your OS is set to a plain US layout instead, these keys will type their US character (e.g. DE_MINUS would type / instead of -).

Note that code_layer and bt_layer in stealth.keymap currently use plain US &kp codes (e.g. &kp AT_SIGN) rather than the DE_* macros, so those two layers assume a US layout and won't produce the labeled character under a Swiss OS layout.

Swiss character reference

Use these instead of the plain US &kp codes whenever you want the printed Swiss/German character (with your OS set to a Swiss German layout). Full list in include/locale/keys_de_swiss.h.

CharacterZMK code
äDE_A_UMLAUT
öDE_O_UMLAUT
üDE_U_UMLAUT
àDE_A_GRAVE
èDE_E_GRAVE
éDE_E_ACUTE
çDE_C_CEDILLA
¨ (diaeresis)DE_UMLAUT
´ (acute accent)DE_ACUTE
°DE_DEGREE / DE_DEG
§DE_SECTION / DE_SECT
€DE_EURO
£DE_POUND_SIGN
¢DE_CENT
¦DE_BROKEN_BAR
¬DE_NOT
~DE_TILDE
`DE_GRAVE
^DE_CARET
\DE_BACKSLASH / DE_BSLH
|DE_PIPE
[DE_LEFT_BRACKET / DE_LBKT
]DE_RIGHT_BRACKET / DE_RBKT
{DE_LEFT_BRACE / DE_LBRC
}DE_RIGHT_BRACE / DE_RBRC
@DE_AT_SIGN / DE_AT
#DE_HASH / DE_POUND
$DE_DOLLAR / DE_DLLR
%DE_PERCENT / DE_PRCNT
&DE_AMPERSAND / DE_AMPS
*DE_ASTERISK / DE_ASTRK / DE_STAR
+DE_PLUS
-DE_MINUS
_DE_UNDERSCORE / DE_UNDER
=DE_EQUAL
/DE_SLASH / DE_FSLH
!DE_EXCLAMATION / DE_EXCL
?DE_QUESTION / DE_QMARK
"DE_DOUBLE_QUOTES / DE_DQT
'DE_SINGLE_QUOTE / DE_SQT / DE_APOS
,DE_COMMA
.DE_PERIOD / DE_DOT
:DE_COLON
;DE_SEMICOLON / DE_SEMI
<DE_LESS_THAN / DE_LT
>DE_GREATER_THAN / DE_GT
(DE_LEFT_PARENTHESIS / DE_LPAR
)DE_RIGHT_PARENTHESIS / DE_RPAR
0-9DE_N0-DE_N9
a-zDE_A-DE_Z (note: DE_Y/DE_Z are swapped to match QWERTZ)
SpaceDE_SPACE

So for a backslash, use &kp DE_BACKSLASH (or the shorter alias &kp DE_BSLH) in place of &kp BSLH - on a Swiss keyboard that's AltGr + the key next to left Shift, and DE_BACKSLASH sends exactly that physical combination.

Using these in ZMK Studio

You can't search for DE_A_UMLAUT (etc.) by name in Studio - these are C preprocessor macros that get replaced with a raw keycode (plus an optional Shift/AltGr/Ctrl modifier) at compile time, so by the time the firmware is running, the name is gone. Studio only ever sees "base key + modifier," and displays the base key using its generic US name.

You can still build the identical binding by hand: in Studio, add a Key Press (&kp) binding, pick the base key from the table below (shown by its Studio/US name), and toggle the matching modifier next to it.

CharacterBase key in StudioModifier
äApostrophe / Quotenone
öSemicolon / Colonnone
üLeft Bracketnone
àApostrophe / QuoteShift
èLeft BracketShift
éSemicolon / ColonShift
ç4Shift
¨ (dead key)Right Bracketnone
´ (dead key)MinusAltGr
°4AltGr
§Grave/Tilde (`)none
€EAltGr
£Backslash/PipeShift
¢8AltGr
¦1AltGr
¬6AltGr
~Equal/PlusAltGr
`Equal/PlusShift
^Equal/Plusnone
\Non-US Backslash/PipeAltGr
|7AltGr
[Left BracketAltGr
]Right BracketAltGr
{Apostrophe / QuoteAltGr
}Backslash/PipeAltGr
@2AltGr
#3AltGr
$Backslash/Pipenone
%5Shift
&6Shift
*3Shift
+1Shift
-Slashnone
_SlashShift
=0Shift
/7Shift
!Right BracketShift
?MinusShift
"2Shift
'Minusnone
,Commanone
.Periodnone
:PeriodShift
;CommaShift
<Non-US Backslash/Pipenone
>Non-US Backslash/PipeShift
(8Shift
)9Shift
yphysical key Znone
zphysical key Ynone

Letters other than y/z and digits 0-9 map 1:1 to the same-named US key, no modifier.

Flashing

Every push builds both halves' firmware via GitHub Actions. Open the latest run under the Actions tab, download the firmware artifact, and unzip it - you'll get one .uf2 file per shield (stealth_left-nice_nano__zmk-zmk.uf2 and stealth_right-nice_nano__zmk-zmk.uf2).

To flash a half: double-tap its reset button to put it into bootloader mode (it shows up as a USB drive named NICENANO), then drag the matching .uf2 file onto that drive. It flashes and reboots automatically.

Editing the layout live with ZMK Studio

The left/central half is built with ZMK Studio support, so you can remap keys without rebuilding or reflashing firmware:

  1. Flash the current firmware to both halves (see above) at least once - Studio only changes the keymap that's already on the device, it doesn't install new firmware.
  2. Connect the left half to your computer with a USB cable (the right half doesn't need Studio and isn't reachable this way).
  3. Open studio.zmk.dev in Chrome (or the ZMK Studio desktop app) and connect to the keyboard - it should be detected automatically over the USB serial connection.
  4. Edit key bindings, layers, etc. in the visual editor. Changes are pushed to the keyboard live and are saved to flash, so they persist across power cycles - no rebuild/reflash needed.

Changes made in Studio live only on the physical keyboard, not in this repo. If you want a change to stick around permanently (e.g. survive a factory reset, or apply after reflashing from a fresh build), port it back into boards/shields/stealth/stealth.keymap by hand.

Parts

74
QtyValueFootprintReferences
27PG1350S1, S2, S10, S11, S12, S13, S14, S15, S16, S17, S18, S19, S20, S21, S22, S23 +11
27ComboDiodeD1, D2, D10, D11, D12, D13, D14, D15, D16, D17, D18, D19, D20, D21, D22, D23 +11
10ceoloide:mounting_hole_platedH1, H2, H3, H4, H5, H6, H7, H8, H9, H10
2E73:SW_TACT_ALPS_SKQGABE010B1, B2
2E73:SPDT_C128955T1, T2
2JST_PH_S2B-PH-K_02x2.00mm_AngledJST1, JST2
1ceoloide:mcu_nice_nanoMCU1
1TRRS-PJ-320A-dualTRRS-PJ-320A-dualTRRS1

The 72 most common of 74 parts.

Similar boards

  • 2 layers141.1 × 126.8 mmCalculator, the printed circuit board in 3D

    Calculator

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    74 parts915
  • 2 layers49 × 44 mmSimple keeb reuser, the printed circuit board in 3D

    Simple keeb reuser

    CRImier/MyKiCad

    My KiCad boards. Can't be bothered uploading individually anymore, so here you go.

    74 parts253GPL-3.0
  • 2 layers49 × 49 mmOSBMS Balancer Rev1 sot323, the printed circuit board in 3D

    OSBMS Balancer Rev1 sot323

    Teslafly/Dead-OpenBMS-dead

    A scalable, open source battery management system

    74 parts248
  • 2 layers72.4 × 72.4 mmSerialResonantFilter, the printed circuit board in 3D

    SerialResonantFilter

    profdc9/RFBitBanger

    A QRP digital transceiver created from readily available parts for off-the-grid maintenance

    74 parts222
  • 2 layers58 × 65 mmSidechain mixer core, the printed circuit board in 3D

    Sidechain mixer core

    shmoergh/moduleur

    Fully analog DIY-friendly modular synth

    74 parts222
  • 2 layers110 × 60 mmArduino Spot Welder, the printed circuit board in 3D

    Arduino Spot Welder

    KaeptnBalu/Arduino_Spot_Welder_V3

    This is the Kicad project for V3.1 The Arduino Board was not changed, only the Mosfet Board got a updgrade.

    74 parts207GPL-3.0
  • 2 layers51.5 × 89 mmMobo, the printed circuit board in 3D

    Mobo

    opulo-inc/feeder

    Source for LumenPnP Feeders

    74 parts202
  • 2 layers165.7 × 152.4 mm8-Bit CPU 32k, the printed circuit board in 3D

    8-Bit CPU 32k

    slu4coder/Minimal-UART-Computer-1-2

    Legacy: Version 1 and 2 of my TTL-only CPU featuring UART I/O, an expansion port, 512KB SSD at up to 10MHz clock speed

    74 parts184

Questions

How big is the Keyboard pcb PCB?

It measures 145.2 × 116.5 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Keyboard pcb use?

74 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Keyboard pcb KiCad files?

From the Neil-Reichlin/Stealth repository on GitHub, at the commit this page was made from: the board is PCBs/pcbs/keyboard_pcb.kicad_pcb and its schematic keyboard/keyboard.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Keyboard pcb design in my own project?

Its repository states no licence, so its author keeps all rights: ask Neil-Reichlin before reusing the design.