2 layers60 × 126.6 mm
V3 Connector + IRLED
PiTracLM/PiTrac
Launch monitor using low-cost raspberry pi and camera hardware to determine ball launch speed, angles and spin. See https://discord.gg/vGuyAAxXJH (permalink)
151 parts439GPL-2.0
2 layers76.1 × 57.2 mm
ProPrj USBreeze 2026-02-05
mr258876/USBreezeA STM32 based USB PWM fan controller for PCs, also supports RGB/ARGB lighting (Windows 11 Dynamic Lighting).
- Size
- 76.1 × 57.2 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 151
- Nets
- 85
- Pads
- 424
- Tracks, vias
- 1,078, 125
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 10 Aug 2025
- Updated
- 6 Feb 2026
Overview
ProPrj USBreeze 2026-02-05 is an open-source printed circuit board by mr258876, from the mr258876/USBreeze repository on GitHub. It is a 2-layer board of 76.1 × 57.2 mm with 151 parts on 85 nets, routed with 1,078 tracks and 125 vias.
Its parts include 58 resistors, 34 capacitors, 17 diodes, 8 transistors and 2 ICs. It belongs with the lEDs and displays boards of this library.
README
README.mdUSBreeze
A STM32F103-based USB PWM fan controller for PCs with RGB/ARGB lighting support (Windows 11 Dynamic Lighting).
[!WARNING] 🚧🚧 PROJECT UNDER CONSTRUCTION 🚧🚧 – use at your own risk.
Features
- 8× PWM fan channels with RPM monitoring
- Offline fan control using the STM32 on-chip temperature sensor and customizable fan curves (works without host software)
- HID LampArray–implemented ARGB control; compatible with Windows 11 Dynamic Lighting
- 3 configurable ARGB channels, supporting up to 256 LEDs in total
Supported Hardware
- The USBreeze board
- Any STM32F103 (C6T6 or above) dev board
Please refer Hardware Readme for pinouts and more info.
Firmware
- Toolchain/IDE: Keil MDK-ARM v5.30.0.0
- How to build: See Firmware Readme
Using USBreeze
Lighting Control
Basic Controls
Control lighting from Settings -> Personalization -> Dynamic lighting (effects, brightness, color).
[!Note] Only Windows 11 Dynamic Lighting tested so far. Effects on other platforms are not guaranteed.
Channel Configurations
- TODO
Fan Control
Basic Controls
Conrtols using FanControl is recommended.
Install both FanControl and FanControl.USBreeze plugin, and you're good to go!
Offline Fan Curve Configurations
- TODO
License
See LICENSE
This repository contains hardware design files and firmware source code released under different licenses. Unless a file states otherwise via an SPDX-License-Identifier, the following defaults apply:
-
Hardware/ (schematics, PCB layout, BOM, fabrication/mechanical sources)
- License: CERN Open Hardware Licence v2 – Weakly Reciprocal
- SPDX: CERN-OHL-W-2.0
- Notes: Keep copyright and license notices. When you distribute products or outputs based on modified hardware, provide the "source" as defined by the licence and include the Source Location.
-
Firmware/ (software/firmware source code)
- License: MIT License
- SPDX: MIT
-
FanControl.USBreeze/ (software source code)
- License: MIT License
- SPDX: MIT
- Notes: see FanControl.USBreeze repository.
Copyright © 2025 mr258876
Parts
151| Qty | Value | Footprint | References |
|---|---|---|---|
| 58 | ProPrj_USBreeze_2026-02-05:R0603 | R1, R2, R10, R11, R12, R13, R14, R15, R16, R17, R18, R19, R20, R21, R22, R23 +42 | |
| 32 | ProPrj_USBreeze_2026-02-05:C0603 | C1, C2, C10, C12, C13, C14, C16, C17, C18, C19, C20, C21, C22, C23, C24, C25 +16 | |
| 17 | ProPrj_USBreeze_2026-02-05:SOT-23-3_L2.9-W1.6-P1.90-LS2.8-BR | D1, D2, D3, D4, D5, D6, D7, D8, D9, D10, D11, D12, D13, D14, D15, D16 +1 | |
| 8 | ProPrj_USBreeze_2026-02-05:SOT-23-3_L2.9-W1.3-P1.90-LS2.4-BR | Q1, Q2, Q3, Q4, Q6, Q7, Q8, Q9 | |
| 8 | ProPrj_USBreeze_2026-02-05:CONN-TH_4P-P2.54_CAX_KF2510-4AGW-GW | FAN0, FAN1, FAN2, FAN3, FAN4, FAN5, FAN6, FAN7 | |
| 3 | ProPrj_USBreeze_2026-02-05:R1206 | FUSE1, FUSE2, FUSE3 | |
| 3 | ProPrj_USBreeze_2026-02-05:ARGB/2.54mm/4-1PIN | RGB_A1, RGB_B1, RGB_C1 | |
| 2 | ProPrj_USBreeze_2026-02-05:CAP-TH_BD8.0-P3.50-D0.6-FD | C33, C34 | |
| 1 | ProPrj_USBreeze_2026-02-05:Pad_e130 | ||
| 1 | ProPrj_USBreeze_2026-02-05:Pad_e125 | ||
| 1 | ProPrj_USBreeze_2026-02-05:Pad_e126 | ||
| 1 | ProPrj_USBreeze_2026-02-05:Pad_e122 | ||
| 1 | ProPrj_USBreeze_2026-02-05:Pad_e131 | ||
| 1 | ProPrj_USBreeze_2026-02-05:USB-C-SMD_TYPE-C16PIN | USB1 | |
| 1 | ProPrj_USBreeze_2026-02-05:Pad_e135 | ||
| 1 | ProPrj_USBreeze_2026-02-05:Pad_e129 | ||
| 1 | ProPrj_USBreeze_2026-02-05:Pad_e124 | ||
| 1 | ProPrj_USBreeze_2026-02-05:Pad_e134 | ||
| 1 | ProPrj_USBreeze_2026-02-05:CRYSTAL-SMD_L11.5-W4.8-LS12.7 | X1 | |
| 1 | ProPrj_USBreeze_2026-02-05:Pad_e123 | ||
| 1 | ProPrj_USBreeze_2026-02-05:Pad_e133 | ||
| 1 | ProPrj_USBreeze_2026-02-05:CONN-TH_4P-P2.50_4PIN | CN1 | |
| 1 | ProPrj_USBreeze_2026-02-05:Pad_e128 | ||
| 1 | ProPrj_USBreeze_2026-02-05:Pad_e127 | ||
| 1 | ProPrj_USBreeze_2026-02-05:LQFP-48_L7.0-W7.0-P0.50-LS9.0-BL | U1 | |
| 1 | ProPrj_USBreeze_2026-02-05:Pad_e132 | ||
| 1 | ProPrj_USBreeze_2026-02-05:SATA 15P | PWR | |
| 1 | ProPrj_USBreeze_2026-02-05:TSSOP-14_L5.0-W4.4-P0.65-LS6.4-BL | U2 |
Questions
How big is the ProPrj USBreeze 2026-02-05 PCB?
It measures 76.1 × 57.2 mm and has 2 copper layers, 1.6 mm thick.
What parts does the ProPrj USBreeze 2026-02-05 use?
151 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ProPrj USBreeze 2026-02-05 KiCad files?
From the mr258876/USBreeze repository on GitHub, at the commit this page was made from: the board is Hardware/ProPrj_USBreeze_2026-02-05.kicad_pcb and its schematic Hardware/KiCad/ProPrj_USBreeze_2026-02-05.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the ProPrj USBreeze 2026-02-05 design in my own project?
Its repository states no licence, so its author keeps all rights: ask mr258876 before reusing the design.
Similar boards
- 2 layers285 × 94.2 mm
- 2 layers250 × 10 mm
Rgbwstrip120 250
cnlohr/cnhardware
My dumping grounds for all my kicad projects and random hardware bringup.
151 parts114 - 2 layers96.3 × 95.9 mm
- 2 layers130 × 120 mm
- 2 layers56 × 95 mm
- 2 layers101.6 × 147.3 mm
Karabas pro revC1
andykarpov/karabas-pro
FPGA based retrocomputer with FDD and HDD controllers
151 parts37MIT - 2 layers242.3 × 75.4 mm
