
Cartridge pmod
joaln27/cartridge_pmod
QSPI flash + PSRAM + audio cartridge Pmod for TinyTapeout — a drop-in remix of the stock QSPI Pmod with sigma-delta audio (RC filter + amp + jack) on the CS2 pin. KiCad, JLC-assemblable

A QSPI Pmod board designed in KiCad containing one Flash and two SPRAMs
Qspi pmod is an open-source printed circuit board by mole99, from the mole99/qspi-pmod repository on GitHub, published under the Apache-2.0 licence. It is a 2-layer board of 30.7 × 20 mm with 15 parts on 14 nets, routed with 171 tracks and 21 vias.
It is built around the W25Q128JVSIM, APS6404L-3SQR-SN and 0402YC104KAT2A, with the C0402C105M9PAC, 2.54-2*6PWZ and 0402CG220J500NT among its other parts. Its parts include 7 capacitors, 3 resistors, 3 ICs and 2 connectors.
A QSPI Pmod board designed in KiCad with one SPI Flash and two PSRAMs.

| Pmod | TinyTapeout | Function | Note |
|---|---|---|---|
| PMOD1 | uio[0] | CS0 (Flash) | Cut trace to disable (see below) |
| PMOD2 | uio[1] | SD0/MOSI | |
| PMOD3 | uio[2] | SD1/MISO | |
| PMOD4 | uio[3] | SCK | Short CK ("CLOCK cap") pin pair for delay by 22pF cap |
| PMOD5 | uio[4] | SD2 | |
| PMOD6 | uio[5] | SD3 | |
| PMOD7 | uio[6] | CS1 (RAM A) | Cut trace to disable (see below) |
| PMOD8 | uio[7] | CS2 (RAM B) | Cut trace to disable (see below) |
[!NOTE] On the bottom side of the PCB, you can cut the traces for any of the 3 CS pins to disable its respective memory IC. When cut, a 1k resistor pulls up the chip's
/CSto disable it. In this case, the respective pin could be used (via header thru-hole on the other side of the cut) as either an input or output.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 100n | Capacitor_SMD:C_0402_1005Metric | C1, C3, C5 |
| 3 | 10k | Resistor_SMD:R_0402_1005Metric | R1, R2, R3 |
| 3 | 1u | Capacitor_SMD:C_0402_1005Metric | C2, C4, C6 |
| 2 | 878-APS6404L-3SQR-SN | Package_SO:SOP-8_3.9x4.9mm_P1.27mm | U2, U3 |
| 1 | 2.54-2*6P Bend insert | tt:PinHeader_2x06_P2.54mm_PMODPeriph2B | J1 |
| 1 | 22pF | Capacitor_SMD:C_0402_1005Metric | C7 |
| 1 | CONFIG | Connector_PinHeader_2.54mm:PinHeader_2x04_P2.54mm_Vertical | J2 |
| 1 | W25Q128JVSIM | Package_SO:SOIC-8_5.23x5.23mm_P1.27mm | U1 |

joaln27/cartridge_pmod
QSPI flash + PSRAM + audio cartridge Pmod for TinyTapeout — a drop-in remix of the stock QSPI Pmod with sigma-delta audio (RC filter + amp + jack) on the CS2 pin. KiCad, JLC-assemblable

BoySanic/sanic-cpu-32
SanicCPU32 (defined hereafter as SC32) is a 32-bit little-endian RISC with an integer ALU, support for up to 23-bit memory (in the current implementation), and 32 general purpose registers.

ak66666/ThumbsUpV3Rp2040
ThumbsUp! v3, a split version of the 4x12 Thumbs Up keyboard with RP2040
ak66666/ThumbsUpV3Rp2040MX
Split version of the Thumbs Up keyboard with RP2040 for MX switches.



mrspieb/HW-FanControl
Everything required to build the PCB and case of the ventilation fan controller
It measures 30.7 × 20 mm and has 2 copper layers, 1.6 mm thick.
15 parts, built around the W25Q128JVSIM, APS6404L-3SQR-SN, 0402YC104KAT2A and C0402C105M9PAC. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the mole99/qspi-pmod repository on GitHub, at the commit this page was made from: the board is qspi-pmod.kicad_pcb and its schematic qspi-pmod.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the Apache-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).