Skip to the content
2 layers82.9 × 62.9 mmATmega328P Minimal Development Board, the printed circuit board in 3D

ATmega328P Minimal Development Board

moaazzz-h/ATmega328P-Minimal-Development-Board

Minimal ATmega328P development board with onboard 5V regulation, ISP & FTDI programming headers, reset circuit, status LEDs, and full I/O breakout — no Arduino required. Designed by Moaaz Hesham.

Size
82.9 × 62.9 mm
Copper layers
2
Thickness
1.6 mm
Parts
28
Nets
32
Pads
114
Tracks, vias
179, 2
Pours
2
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
9 Jul 2026
Updated
9 Jul 2026

Overview

ATmega328P Minimal Development Board is an open-source printed circuit board by moaazzz-h, from the moaazzz-h/ATmega328P-Minimal-Development-Board repository on GitHub, published under the MIT licence. It is a 2-layer board of 82.9 × 62.9 mm with 28 parts on 32 nets, routed with 179 tracks and 2 vias.

It is built around the ATMEGA328-PU. Its parts include 8 capacitors, 6 connectors, 3 resistors, 3 diodes and 2 ICs. It belongs with the microcontroller boards boards and the AVR (ATmega, ATtiny) boards of this library.

Main components

1

README

README.md

ATmega328P Minimal Development Board

A minimal, breadboard-free development board built around the ATmega328P-PU, designed by Moaaz Hesham. It provides onboard power regulation, ISP/FTDI programming headers, a reset circuit, status LEDs, and fully broken-out I/O — everything needed to prototype and program the ATmega328P without an Arduino.

status license

Features

  • 5V regulated power supply — barrel jack or 2-pin screw terminal input, reverse-polarity protection, LM7805 linear regulator
  • ATmega328P-PU in DIP-28 package with 16 MHz crystal oscillator
  • ISP programming via standard 6-pin AVR-ISP header
  • FTDI/UART programming & bootloader support via 6-pin header (RX, TX, RESET with auto-reset cap)
  • Manual reset button with 10k pull-up
  • Two status LEDs (green & blue) on dedicated GPIO-driven pads
  • Full I/O breakout — two 14-pin headers exposing every port pin, AREF, RESET, and power rails
  • 4 mounting holes for enclosure/standoff mounting

Schematic

Schematic

Board Overview

BlockReference DesignatorsDescription
Power SupplyJ1, J2, D1, U1, C1, C2Barrel jack or screw-terminal input → LM7805 → regulated 5V rail
MCU & ClockU2, Y1, C3, C4, C5, C6, C7ATmega328P-PU with 16 MHz crystal and decoupling caps
ISP & FTDI ProgrammingJ3, J4, C86-pin AVR-ISP header + 6-pin FTDI header for serial programming
ResetR1, SW1Push-button reset with pull-up resistor
LEDsR2, R3, D2, D3Green and blue indicator LEDs with current-limiting resistors
I/O BreakoutJ5, J6All GPIO, power, and reference pins broken out to 0.1" headers
MountingH1–H4Mounting holes for chassis/standoff mounting

Power Input

The board accepts power through either:

  • J1 — Barrel jack with integrated switch
  • J2 — 2-pin screw terminal (PWR+ / GND)

Both paths are protected by a 1N5817 Schottky diode (D1) against reverse polarity and regulated to 5V by U1 (LM7805, TO-220). Input and output are bulk-decoupled with 10 µF electrolytic capacitors (C1, C2).

Input voltage: 7–12V DC recommended (typical LM7805 dropout applies)

Programming

The board supports two programming methods:

  1. ISP (In-System Programming) — via J3, a standard 6-pin AVR-ISP header (MISO, MOSI, SCK, RESET, VCC, GND). Use a USBasp, AVRISP mkII, or Arduino-as-ISP.
  2. Serial/FTDI (Bootloader) — via J4, a 6-pin header (GND, RXD, TXD, +5V, RESET) with a 100 nF cap (C8) on RESET for auto-reset, compatible with standard FTDI/USB-to-serial adapters. Requires an Arduino-compatible bootloader to be pre-flashed via ISP.

I/O Breakout

Headers J5 and J6 (14-pin each) expose:

  • J5: RXD, TXD, PD2–PD7, PB0, +5V, GND, +5V, GND, +5V
  • J6: PC5–PC0, AREF, Vin, RESET, SCK, MISO, MOSI, PB2, PB1

This gives access to every digital I/O pin, the ADC-capable PC pins, SPI pins, and AREF for use with breadboards, shields, or custom carrier boards.

Repository Structure

text
.
├── hardware/          # KiCad project files (schematic, PCB, libraries)
├── docs/
│   ├── BOM.md         # Full bill of materials
│   └── pinout.md      # Detailed pin mapping reference
├── LICENSE
└── README.md

Note: Add your KiCad project files (.kicad_sch, .kicad_pcb, .kicad_pro) to hardware/ and export production files (Gerbers, BOM, pick-and-place) to hardware/production/ before tagging a release.

Getting Started

  1. Populate the board per the BOM.
  2. Connect a 7–12V DC supply to J1 or J2.
  3. Flash a bootloader (e.g., Arduino Uno bootloader) via J3 using an ISP programmer.
  4. Connect an FTDI adapter to J4 to upload sketches via the Arduino IDE (select Arduino Uno or ATmega328P (5V, 16MHz) w/ Arduino as ISP as the board).
  5. Use J5/J6 to wire up peripherals.

License

Hardware design files are released under the CERN Open Hardware Licence v2 - Strongly Reciprocal (or replace with your preferred license — MIT/CC-BY-SA are also common for hobby boards). See LICENSE.

Credits

Designed by Moaaz Hesham.

Parts

28
QtyValueFootprintReferences
4100nFCapacitor_THT:C_Disc_D5.0mm_W2.5mm_P2.50mmC3, C4, C7, C8
4MountingHole_PadMountingHole:MountingHole_3.2mm_M3_PadH1, H2, H3, H4
210uFCapacitor_THT:CP_Radial_D5.0mm_P2.50mmC1, C2
222pFCapacitor_THT:C_Disc_D5.0mm_W2.5mm_P2.50mmC5, C6
2330Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR2, R3
2Conn_01x14_PinConnector_PinSocket_2.54mm:PinSocket_1x14_P2.54mm_VerticalJ5, J6
110kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR1
116MHzCrystal:Crystal_HC49-U_VerticalY1
11N5817Diode_THT:D_DO-41_SOD81_P10.16mm_HorizontalD1
1ATmega328-PPackage_DIP:DIP-28_W7.62mmU2
1AVR-ISP-6Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_VerticalJ3
1BLUELED_THT:LED_D3.0mmD3
1Barrel_Jack_SwitchConnector_BarrelJack:BarrelJack_HorizontalJ1
1Conn_01x06_PinConnector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_VerticalJ4
1GREENLED_THT:LED_D3.0mmD2
1LM7805_TO220Package_TO_SOT_THT:TO-220-3_VerticalU1
1SW_PushButton_Switch_THT:SW_PUSH_6mmSW1
1Screw_Terminal_01x02TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_HorizontalJ2

Similar boards

  • 2 layers104.9 × 75.2 mmHandipi kb, the printed circuit board in 3D

    Handipi kb

    brickbots/HandiPi

    Handheld RPI4 based computer with keyboard and display

    95 parts814MIT
  • 2 layers228 × 98 mmPlaid, the printed circuit board in 3D

    Plaid

    hsgw/plaid

    12x4 ortholinear usb keyboard made by Through Hole components ONLY.

    139 parts779MIT
  • 2 layers94.6 × 46.1 mmHeaterMeterPI, the printed circuit board in 3D

    HeaterMeterPI

    CapnBry/HeaterMeter

    HeaterMeter and LinkMeter Arduino BBQ Controller

    66 parts557MIT
  • 2 layers50 × 50 mmAvrcraft poed, the printed circuit board in 3D

    Avrcraft poed

    cnlohr/avrcraft

    Minecraft server optimized for 8-bit devices.

    58 parts471
  • 2 layers284.7 × 94.2 mmLumberjack, the printed circuit board in 3D

    Lumberjack

    peej/lumberjack-keyboard

    5x12 ortholinear through-hole component keyboard PCB for standard 60% cases

    165 parts403MIT
  • 2 layers132.1 × 45.7 mmIPoS, the printed circuit board in 3D

    IPoS

    peterheinrich/InternetOverSpaghetti

    Transmitting IP packages over a pair of spaghetti thus demonstrating how media independent IP really is.

    42 parts342
  • 2 layers63.3 × 57.2 mmRam Tester, the printed circuit board in 3D

    Ram Tester

    tops4u/Ram-Tester

    Ram Tester for vintage CBM Computer RAM Chips

    42 parts118
  • 2 layers285 × 117 mmTartan, the printed circuit board in 3D

    Tartan

    hsgw/tartan

    60% keyboard made by through-hole parts only

    171 parts98

Questions

How big is the ATmega328P Minimal Development Board PCB?

It measures 82.9 × 62.9 mm and has 2 copper layers, 1.6 mm thick.

What parts does the ATmega328P Minimal Development Board use?

28 parts, built around the ATMEGA328-PU. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the ATmega328P Minimal Development Board KiCad files?

From the moaazzz-h/ATmega328P-Minimal-Development-Board repository on GitHub, at the commit this page was made from: the board is ATmega328P Minimal Development Board/ATmega328P Minimal Development Board.kicad_pcb and its schematic ATmega328P Minimal Development Board/ATmega328P Minimal Development Board.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the ATmega328P Minimal Development Board design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).