

Motor
- Size
- 36.2 × 24 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 44
- Nets
- 63
- Pads
- 186
- Tracks, vias
- 435, 52
- Pours
- 17
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 13 Mar 2017
- Updated
- 14 Mar 2020
Overview
Motor is an open-source printed circuit board by mkramar, from the mkramar/dizzyrobot repository on GitHub. It is a 2-layer board of 36.2 × 24 mm with 44 parts on 63 nets, routed with 435 tracks and 52 vias.
It is built around the STSPIN32F0, RS485 and PSMN3R3-40YS, with the CD0603-B0340R among its other parts. Its parts include 10 connectors, 9 resistors, 7 capacitors, 6 diodes and 6 transistors. It belongs with the robots and motor control boards of this library.
Main components
4STSPIN32F0
VFQFPN-48(7x7)-40℃~+125℃@(TJ) 16 32KB 4KB 8V~45V ARM Cortex-M0 FLASH VFQFPN-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)RS485
SOP-81 1 1.2mA 2.5Mbps 256 5V Half-Duplex Transceiver ±4kV SOP-8 RS-485 / RS-422 ICs ROHSGRRS-485 / RS-422 ICsPSMN3R3-40YS
SOT-669-55℃~+175℃ 1 N-channel 100A 117W 2.754nF 3.3mΩ@10V 40V 49nC@10V 4V SOT-669 MOSFETs ROHSNexperiaMOSFETsCD0603-B0340R
0603-40℃~+125℃ 1 Independent 2A 300mA 40V 50uA@10V 550mV@200mA 0603 Schottky Diodes ROHSBournsSchottky Diodes
Parts
44| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 10 | Resistors_SMD:R_0603 | R3, R4, R5, R6, R7, R8 |
| 6 | PSMN3R3-40YS | Dizzy:PSMN3R3-40YS | Q1, Q2, Q3, Q4, Q5, Q6 |
| 4 | 1uF | Capacitors_SMD:C_0603 | C4, C5, C6, C7 |
| 3 | 200 | Resistors_SMD:R_0603 | R1, R2, R9 |
| 3 | GND | Pin_Headers:Pin_Header_Straight_1x01_Pitch2.54mm | J4, J7, J9 |
| 2 | LED | LEDs:LED_0603 | D3, D5 |
| 2 | SWiTCH | Resistors_SMD:R_1206 | CALIB, ID |
| 1 | 100uF | Capacitors_SMD:C_0805 | C1 |
| 1 | 10uF | Capacitors_SMD:C_1206 | C3 |
| 1 | 12 | Pin_Headers:Pin_Header_Straight_1x01_Pitch2.54mm | J6 |
| 1 | 22uF | Capacitors_SMD:C_0805 | C2 |
| 1 | 22uH | Inductors_SMD:L_1210 | L1 |
| 1 | 47v | Diodes_SMD:D_SOD-123F | D6 |
| 1 | 8Mhz | Dizzy:Oscillator | Y1 |
| 1 | CD0603-B0340R | LEDs:LED_0603 | D2 |
| 1 | CD0603-B0340R | Diodes_SMD:D_SOD-323F | D1 |
| 1 | CONN_02X05 | Pin_Headers:Pin_Header_Straight_2x05_Pitch1.27mm | J1 |
| 1 | D | Diodes_SMD:D_SOD-323F | D4 |
| 1 | LTC2876 | Dizzy:LTC2876 | U2 |
| 1 | RS485 | Pin_Headers:Pin_Header_Straight_1x02_Pitch2.54mm | J3 |
| 1 | SPI | Dizzy:SPI_CONN | J2 |
| 1 | STSPIN32F0 | Dizzy:STSPIN32F0 | U1 |
| 1 | U | Pin_Headers:Pin_Header_Straight_1x01_Pitch2.54mm | J12 |
| 1 | V | Pin_Headers:Pin_Header_Straight_1x01_Pitch2.54mm | J11 |
| 1 | W | Pin_Headers:Pin_Header_Straight_1x01_Pitch2.54mm | J13 |
More from mkramar/dizzyrobot
11- 2 layers45 × 45 mm

- 4 layers45 × 140 mm

- 2 layers45 × 45 mm

- 2 layers65 × 29.9 mm

- 2 layers45 × 45 mm

- 2 layers45 × 45 mm

- 2 layers27.1 × 65.7 mm

- 2 layers26.8 × 39.4 mm

- 2 layers12 × 27 mm

- 2 layers13.2 × 9.1 mm

- 2 layers13.2 × 9.1 mm

Similar boards
- 2 layers45 × 45 mm

- 4 layers99 × 100 mm

- 4 layers24.5 × 15.7 mm

- 2 layers139.7 × 100.3 mm

Achterart
CounterPillow/achterart
An 8-way USB-to-UART converter board based on the CH348 chip
63 parts2 - 2 layers53.4 × 45 mm

Temp controlled fan v1 0
Lizzie2105/37degrees_temp_controlled_fan
37 Degrees Inc take home assignment. Include the design files and all documents.
39 parts - 2 layers30 × 33.2 mm

- 2 layers145.3 × 72.6 mm

Power Electronics Board
formulaslug/fs-4-schematics
Electrical Design Repository for fs-4 schematics and PCBs
71 parts7 - 2 layers100 × 100 mm

Explorer
anyshake/explorer
🌏 Detecting seismic wave using 3 geophones and 3-axis accelerometer, pack & send data to AnyShake Observer over RS232 / RS485 serial.
266 parts100
Questions
How big is the Motor PCB?
It measures 36.2 × 24 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Motor use?
44 parts, built around the STSPIN32F0, RS485, PSMN3R3-40YS and CD0603-B0340R. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Motor KiCad files?
From the mkramar/dizzyrobot repository on GitHub, at the commit this page was made from: the board is Schamatic/Motor/motor.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Motor design in my own project?
Its repository states no licence, so its author keeps all rights: ask mkramar before reusing the design.