

[WIP] Open hardware concept: button-free wireless USB sticks. 3D explorer, plan, test lab, fab files.
- Size
- 46.5 × 17.4 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 12
- Nets
- 8
- Pads
- 104
- Tracks, vias
- 59, 27
- Pours
- 5
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 26 Oct 2026
- Updated
- 26 Oct 2026
Overview
Stick is an open-source printed circuit board by mkalmousli, from the mkalmousli/tandem-stick repository on GitHub, published under the MIT licence. It is a 4-layer board of 46.5 × 17.4 mm with 12 parts on 8 nets, routed with 59 tracks and 27 vias.
It is built around the ESP32-S3-MINI-1-N4R2, AP2112K-3.3 and WS2812B-2020. Its parts include 5 capacitors, 2 ICs, 1 resistor, 1 diode and 1 connector. It belongs with the ESP32 boards of this library.
Main components
3ESP32-S3-MINI-1-N4R2
SMD-103.5dBm -40℃~+85℃ 2.4GHz 20.5dBm 355mA 3V~3.6V 95mA Bluetooth5.0 ESP32-S3 On-board PCB Antenna UART、SPI、I2C、GPIO、I2S、USB SMD WiFi Modules ROHSEspressif SystemsWiFi ModulesAP2112K-3.3
SOT253.3V 600mA CMOS Low Dropout Linear Regulator with EnableDiodes IncorporatedUncategorisedWS2812B-2020
SMD,2.2x2mm0.6mA 0.84mm 120us 160mcd 200mcd 2kHz 2mm 2mm 300ns 470.4nm 515.6nm 520mcd 5V 622.5nm 800Kbit/s Built-in power-on reset circuit、Built-in power-on reset circuit、Integrated intelligent reverse connection protection function Top-mount SMD,2.2x2mm RGB LEDs(Built-in IC) ROHSWorldsemiRGB LEDs(Built-In IC)
README
hardware/README.mdTandem Stick: board
KiCad 7 board generated by build_board.py (pcbnew API): python3 build_board.py && python3 drc.py report.txt.
- 33 × 17.4 mm main board plus a 13.5 mm USB-A tab (46.5 mm overall), 4 layers (signal, GND, 3V3, GND), 1.6 mm.
fab/gerbers/Gerbers and drill,fab/bom.csv,fab/pos.csvfor assembly. J1 is the board's own USB-A tab and TP1/TP2 are test pads, so none of them are in the BOM. Order ENIG (gold) finish for the plug pads.- Fill the LCSC column and confirm stock and rotation offsets in the fab's preview before ordering.
Flash
Short TP1 (BOOT) to TP2 (GND) while plugging in, then flash over USB (ESP32-S3 native USB).
Known limits (not tested on hardware)
- DRC: 0 unconnected pads; only library-path and courtyard warnings remain (C1, C2 and U2 courtyards touch). No schematic or ERC; nets are in
build_board.py. - No ESD diode (planned for the respin). C3 (100 nF) sits on the back side under the module power pads, connected by via-in-pad: ask the fab for filled or tented vias, or accept the small solder-wicking risk.
- LED runs from 3.3 V and may be dim.
- Antenna end (x < 5.9 mm) is keepout on all layers; keep the case and your hand away from it.
- First article may need a respin. Order the minimum quantity first.
Parts
12| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 100nF | C_0402_1005Metric | C3, C4 |
| 2 | 10uF | C_0603_1608Metric | C1, C2 |
| 1 | 10k | R_0402_1005Metric | R1 |
| 1 | 1uF | C_0402_1005Metric | C5 |
| 1 | AP2112K-3.3 | SOT-23-5 | U2 |
| 1 | BOOT | TestPoint_Pad_D1.0mm | TP1 |
| 1 | ESP32-S3-MINI-1-N4 | ESP32-S3-MINI-1 | U1 |
| 1 | GND | TestPoint_Pad_D1.0mm | TP2 |
| 1 | USB-A edge plug | J1 | |
| 1 | WS2812B-2020 | LED_WS2812B-2020_PLCC4_2.0x2.0mm | D1 |
Similar boards
- 2 layers26 × 28 mm

- 4 layers35 × 85 mm

Vimdrones esc development board
VimDrones/AM32_esc_development_board
Open Source AM32 ESC development board
95 parts44GPL-3.0 - 4 layers66 × 36 mm

Gas sensor
JamesTwallin/gas_sensor
A tiny plug-in board for the rev E phone-companion board. It stands upright in a notch in rev E's sensor end, between the two gas sensor cans, and pokes 4.5 mm out through a slot in the case face, so its tip sits in the…
81 parts7MIT - 2 layers54.4 × 140 mm

- 2 layers40 × 22.1 mm

- 4 layers25 × 25 mm

- 2 layers52.5 × 55.8 mm

- 2 layers45.1 × 43.2 mm

Star Notifier
aayanrahman/Star-Notifier
Star-shaped USB-C ESP32-C3 board that lights up when Claude or Cursor is done
40 parts
Questions
How big is the Stick PCB?
It measures 46.5 × 17.4 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Stick use?
12 parts, built around the ESP32-S3-MINI-1-N4R2, AP2112K-3.3 and WS2812B-2020. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Stick KiCad files?
From the mkalmousli/tandem-stick repository on GitHub, at the commit this page was made from: the board is hardware/stick.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Stick design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).