Skip to the content
2 layers30 × 20 mmVCO SIP, the printed circuit board in 3D

Analogue SIP modules

Size
30 × 20 mm
Copper layers
2
Thickness
0.8 mm
Parts
40
Nets
33
Pads
127
Tracks, vias
454, 23
Pours
2
Routed
Yes
KiCad
KiCad 4
Created
27 Dec 2014
Updated
2 Mar 2015

Overview

VCO SIP is an open-source printed circuit board by minisystem, from the minisystem/SIP-Modules repository on GitHub. It is a 2-layer board of 30 × 20 mm with 40 parts on 33 nets, routed with 454 tracks and 23 vias.

It is built around the CA3140, LM311M and BAV70, with the BCM847BS among its other parts. Its parts include 22 resistors, 8 capacitors, 4 ICs, 2 transistors and 1 diode.

Main components

4

README

VC-ADSR-SIP/README.md

Voltage Controlled ADSR Envelope Generator

This is a voltage controlled Envelope Generator (EG) with Attack, Decay, Sustain and Release stages in a 30 mm x 18 mm 12 pin SIP package. It is derived from similar designs by Massimo Ischia and Scott Rider (OldCrow) with modifications to respond to 0-10V control voltages and to produce a 0-10V output.

Massimo Ischia's version: http://digilander.libero.it/ismsynth/vc-adsr-1.2.jpg

Scott Rider's version: http://www.muffwiggler.com/forum/viewtopic.php?p=1151245 (scroll down for schematic in thread)

Notes

Ideally, I'd like to eliminate the trimmers for Attack and Decay/Release times. I tried doing this in an early revision but needed to tweak the resistor values more than I expected so reverted to trimmers. However, in subsequent revisions I've hardly needed to make any adjustments at all. A 0603 or 0805 resistor should be able to bridge the T1 and T2 footprints.

Q1's schematic symbol has a pin numbering that swapped the emitter (pin 1) and base (pin 2) when used with the default SOT23 footprint. I fixed this by swapping the pad numbers on the SOT23 footprint module, but this change applies to this project only.

This project was created in Kicad 4022 but routed in 5112 using the CERN push and shove router. This means that the CvPcb footprint association uses the legacy library format and not the new library table format. I haven't tried to do the conversion yet.

Parts

40
QtyValueFootprintReferences
656KSM0603-JRLR5, R7, R9, R10, R12, R19
4100pSM0603-JRLC3, C5, C6, C9
410KSM0603-JRLR1, R6, R14, R16
315KSM0603-JRLR17, R18, R21
2100nSM0603-JRLC1, C2
21MSM0603-JRLR2, R3
11.5MSM0603-JRLR13
1100KPVG3TP1
118pSM0603-JRLC8
11K 3300ppm/KSM0805-HANDTC1
12.2n 1%SM0805-HANDC7
120KSM0603-JRLR15
13.3KSM0603-JRLR23
133KSM0603-JRLR22
139KSM0603-JRLR8
1680SM0603-JRLR20
191KSM0603-JRLR4
1BAV70SOT23-JRLD1
1BCM847SOT363-JRLQ1
1CA3140SOIC-8-JRLU3
1CONN_12CONN_12X_0100_SMD_THRUHOLEP1
1LM311MTSSOP8-JRLU4
1MMBF4391LT1GSOT23-JRLQ2
1TL072-TSSOP8-JRLU2
1TL074-github-smd:TSSOP-14U1

More from minisystem/SIP-Modules

4
  • 2 layers50 × 19 mmVCF VCA SIP OLD, the printed circuit board in 3D

    VCF VCA SIP OLD

    minisystem/SIP-Modules

    Analogue SIP modules

    43 parts11
  • 2 layers30 × 20 mmVCO SIP - Copy, the printed circuit board in 3D

    VCO SIP - Copy

    minisystem/SIP-Modules

    Analogue SIP modules

    43 parts11
  • 2 layers30 × 18 mmVC ADSR SIP, the printed circuit board in 3D

    VC ADSR SIP

    minisystem/SIP-Modules

    Analogue SIP modules

    40 parts11

Similar boards

  • 4 layers60 × 110 mmNeptune, the printed circuit board in 3D

    Neptune

    wntrblm/Neptune

    A salty diode ladder filter

    279 parts44
  • 2 layers132.1 × 213.4 mmVCF VCA BBD board, the printed circuit board in 3D

    VCF VCA BBD board

    JordanAceto/josh_Ox_ribbon_synth

    ribbon synth for Josh Oxford

    436 parts1CC-BY-4.0
  • 2 layers152.1 × 64.7 mmMix, the printed circuit board in 3D

    Mix

    thismatters/EurorackMix

    Simple module for audio signal mixing

    70 parts1
  • 2 layers30 × 237.9 mmVca, the printed circuit board in 3D

    Vca

    thismatters/EurorackVca

    Voltage Control Amplifier for Eurorack -- Based on Yusynth Simple VCA

    67 parts1
  • 2 layers50 × 80 mmVco mk1, the printed circuit board in 3D

    Vco mk1

    Windfisch/analog-synth

    A low-cost semimodular analog synthesizer

    90 parts31GPL-3.0
  • 2 layers19.5 × 108.6 mmIVCA Main, the printed circuit board in 3D

    IVCA Main

    Thorinair/Avalon-Harmonics

    A collection of Avalon Harmonics branded synthesizer modules.

    40 parts26CC-BY-SA-4.0
  • 2 layers58.4 × 50.8 mmMinimoog LPF, the printed circuit board in 3D

    Minimoog LPF

    JordanAceto/VCF_plug_in_boards

    Various small synthesizer Voltage Controlled Filter pcbs

    71 parts11CC-BY-4.0

Questions

How big is the VCO SIP PCB?

It measures 30 × 20 mm and has 2 copper layers, 0.8 mm thick.

What parts does the VCO SIP use?

40 parts, built around the CA3140, LM311M, BAV70 and BCM847BS. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the VCO SIP KiCad files?

From the minisystem/SIP-Modules repository on GitHub, at the commit this page was made from: the board is VCO SIP 2.0/BACKUP 3 CA3140 pin fix - Copy/VCO SIP.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the VCO SIP design in my own project?

Its repository states no licence, so its author keeps all rights: ask minisystem before reusing the design.