Skip to the content
2 layers52.5 × 39.5 mmAssignment, the printed circuit board in 3D

KiCad and NI Multisim files for a TL062-based precision full-wave rectifier

Size
52.5 × 39.5 mm
Copper layers
2
Thickness
1.6 mm
Parts
16
Nets
11
Pads
37
Tracks, vias
100, 2
Pours
1
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
9 Aug 2026
Updated
9 Aug 2026

Overview

Assignment is an open-source printed circuit board by mattnurdean, from the mattnurdean/precision-full-wave-rectifier repository on GitHub. It is a 2-layer board of 52.5 × 39.5 mm with 16 parts on 11 nets, routed with 100 tracks and 2 vias.

It is built around the TL062 and BAT46. Its parts include 6 resistors, 3 connectors, 2 capacitors, 2 diodes and 1 IC.

Main components

2

README

README.md

Circuit Design and Simulation - Precision Full-Wave Rectification

Prepared by: Muhammad Nuruddin bin Muktaruddin

1. Objective

The primary goal of this project is to develop practical skills in designing, simulating, and routing a Printed Circuit Board (PCB) . Specifically, this project demonstrates the complete hardware development workflow by simulating circuit logic in NI Multisim and executing the physical board layout using KiCad .

A precision full-wave rectifier (often called an absolute value circuit) was selected for the design . Theoretically, the standard passive diode rectifiers are limited by their forward voltage drop (typically 0.3V to 0.7V) . If an AC signal is smaller than this drop, standard diodes will block it or heavily distort it . A precision rectifier solves this by placing the diodes inside the negative feedback loop of an operational amplifier (in this case, the TL062) .

The op-amp effectively cancels out the diode's voltage drop which allowing the circuit to act as an "ideal diode" . There are two stages, a half-wave rectifier stage to capture the positive peaks, and a summing amplifier stage to invert and "fold" the negative peaks upward . This allows high-fidelity rectification of very small AC signals (such as 1Vrms) into a continuous, positive DC-pulsed waveform.

2. Simulation

Prior to physical layout, the circuit architecture was designed and validated using NI Multisim . The design utilizes a TL062 dual operational amplifier in a two-stages topology .

  • Stage 1 (Super-Diode): A half-wave rectifier stage with a gain of -1 (utilizing 10kΩ input and feedback resistors) . This stage utilizes 1N4148 standard switching diodes (100V, 200mA, National Semiconductor) to capture the positive peaks .
  • Stage 2 (Summing Amplifier): An inverting summing amplifier with a 68k feedback resistor that mathematically subtracts the scaled original signal from the half-wave signal to "fold" the negative peaks upward .

Thus, injecting a 1Vrms, 1kHz sine wave test signal confirmed the theoretical model . The simulation output displayed a continuous, fully rectified waveform with clean, symmetrical positive arches, demonstrating the successful mathematical summation and amplification of the signal .

3. PCB Design

The validated logic was translated into a physical PCB layout using KiCad . To facilitate robust laboratory prototyping and manual DMM and Oscilloscope probing, all components were assigned to standard Through-Hole Technology (THT) footprints .

There are implemented steps workflow:

  • Schematic Definition: Define all symbols and components in the schematic editor to match the simulated architecture .
  • Component Verification: Ensure the exact components and correct values are used, strictly defining pin polarity and assigning the proper physical footprints .
  • PCB Layout: Translate the schematic to the PCB Editor . Define the board dimensions using edge cuts and route the front and back layers of copper using vias . Ensure the power port supply direction is correct, apply correct silkscreen labelling, and draw the rule area and fill zone to establish the ground plane .
  • Validation & Fabrication: Execute a comprehensive Design Rule Check (DRC) to guarantee there are no layout errors, then proceed to print the circuit board and begin the soldering phase .
  • Soldering & Assembly: Re-verify all correct components, values, and polarities before placement . Apply standard safety practices during soldering and strict Electrostatic Discharge (ESD) precautions, specifically avoiding direct skin contact with the surface board .

4. PCB Validation & Troubleshooting

  • Visual Inspection: Conducted a physical inspection to verify correct component polarity (diodes and IC orientation) and inspect the soldering quality for cold joints or bridges .
  • Cold Test: By using a DMM for continuity checks to verify solder connections and layout trace routing without power .
  • Dynamic Test: Injected a 1Vrms signal using a function generator . Used a 2-channel oscilloscope to simultaneously measure the unrectified Input (Ch 1) and the final Output (Ch 2) .
Figure 4.1: Back plane of PCBFigure 4.2: Front plane of PCB

5. Conclusion

To conclude, this project successfully developed practical skills in simulating, designing, validating, and troubleshooting electronic circuits . The physical assembly and debugging process reinforced the critical importance of verifying correct component values, exact polarity, and physical orientation prior to soldering . Ultimately, both the simulation and hardware analysis successfully proved the theoretical concept of the precision full-wave rectifier .

Parts

16
QtyValueFootprintReferences
210kΩResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR3, R5
251kΩResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR4, R6
2BAT46Diode_THT:D_DO-35_SOD27_P7.62mm_HorizontalD1, D3
2MountingHoleMountingHole:MountingHole_3.2mm_M3_DIN965_PadH1, H2
1100nFCapacitor_THT:C_Disc_D5.0mm_W2.5mm_P5.00mmC2
13.3nFCapacitor_THT:C_Disc_D5.0mm_W2.5mm_P5.00mmC1
15kΩResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR2
15ΩResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR1
1Input_signalConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ2
1Output_signalConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ3
1Power_inputTerminalBlock_MetzConnect:TerminalBlock_MetzConnect_Type086_RT03403HBLC_1x03_P3.81mm_HorizontalJ1
1TL062Package_DIP:DIP-8_W7.62mm_LongPadsU1

Similar boards

  • 2 layers138.4 × 91.4 mmSTM32 MegaBlaster, the printed circuit board in 3D

    STM32 MegaBlaster

    AidanHockey5/STM32_VGM_Player_YM2612_SN76489

    A Sega Genesis music player based off of the STM32 BluePill board and real YM2612+SN76489 sound chips.

    96 parts117AGPL-3.0
  • 4 layers39.4 × 110.3 mmBetula Main, the printed circuit board in 3D

    Betula Main

    Cs4System/Eurorack

    Blattwerk Eurorack modules. Designed by Lorenz Neumann

    176 parts83
  • 2 layers118.7 × 100.1 mmPowerBoard 1, the printed circuit board in 3D

    PowerBoard 1

    arneman44/Modular-Lab-PowerSupply

    The STM32 project are build with cubeMX with as toolchain makefile. I use vscode with STM32-for-vscode to build it

    166 parts1
  • 2 layers49.5 × 49.5 mmTrivial lm399, the printed circuit board in 3D

    Trivial lm399

    cellularmitosis/basic-lm399

    A very basic LM399 voltage reference board design.

    27 parts1MIT
  • 2 layers102.5 × 67.3 mmHorno, the printed circuit board in 3D

    Horno

    daavidclv/mini-HORNO-PCB

    Diseño completo de PCB para un mini horno, desde el esquemático hasta los ficheros de fabricación (Gerbers).

    50 parts
  • 4 layers92 × 75.4 mmMPPT Inverter, the printed circuit board in 3D

    MPPT Inverter

    DavidBojanovic08/Inverter

    Schematic and PCB

    61 parts
  • 2 layers118.3 × 42.7 mmPCB piezo filter v3, the printed circuit board in 3D

    PCB piezo filter v3

    djorgeext/PCB_piezo-filter_v4

    Fourth version of a pre-conditioning circuit for an analog PCG signal based on a piezoelectric sensor.

    48 parts
  • 2 layers98 × 36 mmSk245-oscar cv in, the printed circuit board in 3D

    Sk245-oscar cv in

    mirdej/synkie

    The Synkie is a modular open source analog video processor, developed by Michael Egger, Max Egger and Flo Kaufmann

    56 parts47

Questions

How big is the Assignment PCB?

It measures 52.5 × 39.5 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Assignment use?

16 parts, built around the TL062 and BAT46. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Assignment KiCad files?

From the mattnurdean/precision-full-wave-rectifier repository on GitHub, at the commit this page was made from: the board is Assignment.kicad_pcb and its schematic Assignment.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Assignment design in my own project?

Its repository states no licence, so its author keeps all rights: ask mattnurdean before reusing the design.