
STM32 MegaBlaster
AidanHockey5/STM32_VGM_Player_YM2612_SN76489
A Sega Genesis music player based off of the STM32 BluePill board and real YM2612+SN76489 sound chips.

KiCad and NI Multisim files for a TL062-based precision full-wave rectifier
Assignment is an open-source printed circuit board by mattnurdean, from the mattnurdean/precision-full-wave-rectifier repository on GitHub. It is a 2-layer board of 52.5 × 39.5 mm with 16 parts on 11 nets, routed with 100 tracks and 2 vias.
It is built around the TL062 and BAT46. Its parts include 6 resistors, 3 connectors, 2 capacitors, 2 diodes and 1 IC.
The primary goal of this project is to develop practical skills in designing, simulating, and routing a Printed Circuit Board (PCB) . Specifically, this project demonstrates the complete hardware development workflow by simulating circuit logic in NI Multisim and executing the physical board layout using KiCad .
A precision full-wave rectifier (often called an absolute value circuit) was selected for the design . Theoretically, the standard passive diode rectifiers are limited by their forward voltage drop (typically 0.3V to 0.7V) . If an AC signal is smaller than this drop, standard diodes will block it or heavily distort it . A precision rectifier solves this by placing the diodes inside the negative feedback loop of an operational amplifier (in this case, the TL062) .
The op-amp effectively cancels out the diode's voltage drop which allowing the circuit to act as an "ideal diode" . There are two stages, a half-wave rectifier stage to capture the positive peaks, and a summing amplifier stage to invert and "fold" the negative peaks upward . This allows high-fidelity rectification of very small AC signals (such as 1Vrms) into a continuous, positive DC-pulsed waveform.
Prior to physical layout, the circuit architecture was designed and validated using NI Multisim . The design utilizes a TL062 dual operational amplifier in a two-stages topology .
Thus, injecting a 1Vrms, 1kHz sine wave test signal confirmed the theoretical model . The simulation output displayed a continuous, fully rectified waveform with clean, symmetrical positive arches, demonstrating the successful mathematical summation and amplification of the signal .
The validated logic was translated into a physical PCB layout using KiCad . To facilitate robust laboratory prototyping and manual DMM and Oscilloscope probing, all components were assigned to standard Through-Hole Technology (THT) footprints .
There are implemented steps workflow:
| Figure 4.1: Back plane of PCB | Figure 4.2: Front plane of PCB |
To conclude, this project successfully developed practical skills in simulating, designing, validating, and troubleshooting electronic circuits . The physical assembly and debugging process reinforced the critical importance of verifying correct component values, exact polarity, and physical orientation prior to soldering . Ultimately, both the simulation and hardware analysis successfully proved the theoretical concept of the precision full-wave rectifier .
| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 10kΩ | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R3, R5 |
| 2 | 51kΩ | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R4, R6 |
| 2 | BAT46 | Diode_THT:D_DO-35_SOD27_P7.62mm_Horizontal | D1, D3 |
| 2 | MountingHole | MountingHole:MountingHole_3.2mm_M3_DIN965_Pad | H1, H2 |
| 1 | 100nF | Capacitor_THT:C_Disc_D5.0mm_W2.5mm_P5.00mm | C2 |
| 1 | 3.3nF | Capacitor_THT:C_Disc_D5.0mm_W2.5mm_P5.00mm | C1 |
| 1 | 5kΩ | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R2 |
| 1 | 5Ω | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1 |
| 1 | Input_signal | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J2 |
| 1 | Output_signal | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J3 |
| 1 | Power_input | TerminalBlock_MetzConnect:TerminalBlock_MetzConnect_Type086_RT03403HBLC_1x03_P3.81mm_Horizontal | J1 |
| 1 | TL062 | Package_DIP:DIP-8_W7.62mm_LongPads | U1 |

AidanHockey5/STM32_VGM_Player_YM2612_SN76489
A Sega Genesis music player based off of the STM32 BluePill board and real YM2612+SN76489 sound chips.


arneman44/Modular-Lab-PowerSupply
The STM32 project are build with cubeMX with as toolchain makefile. I use vscode with STM32-for-vscode to build it

cellularmitosis/basic-lm399
A very basic LM399 voltage reference board design.

daavidclv/mini-HORNO-PCB
Diseño completo de PCB para un mini horno, desde el esquemático hasta los ficheros de fabricación (Gerbers).


djorgeext/PCB_piezo-filter_v4
Fourth version of a pre-conditioning circuit for an analog PCG signal based on a piezoelectric sensor.

mirdej/synkie
The Synkie is a modular open source analog video processor, developed by Michael Egger, Max Egger and Flo Kaufmann
It measures 52.5 × 39.5 mm and has 2 copper layers, 1.6 mm thick.
16 parts, built around the TL062 and BAT46. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the mattnurdean/precision-full-wave-rectifier repository on GitHub, at the commit this page was made from: the board is Assignment.kicad_pcb and its schematic Assignment.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask mattnurdean before reusing the design.