martinribelotta/h7value12stm32h7 value line board
Proto h750 is an open-source printed circuit board by martinribelotta, from the martinribelotta/h7value repository on GitHub. It is a 2-layer board of 63.5 × 73.7 mm with 64 parts on 121 nets, routed with 1,248 tracks and 83 vias.
It is built around the STM32H750VBT6, KSZ8081RNACA and S25FL132K0XMFI010. Its parts include 24 capacitors, 16 resistors, 9 connectors, 4 ICs and 3 switches. It belongs with the STM32 boards of this library.
Simple board for stm32h750 value line device in LQFP100 package.
Require KiCAD 5.0 or higer
| Qty | Value | Footprint | References |
|---|---|---|---|
| 14 | 100n | Capacitor_SMD:C_0805_2012Metric | C1, C2, C3, C4, C7, C8, C10, C12, C13, C14, C18, C19, C22, C23 |
| 8 | 0R | Resistor_SMD:R_2010_5025Metric | R8, R9, R10, R11, R12, R13, R14, R15 |
| 5 | 10K | Resistor_SMD:R_0805_2012Metric | R3, R4, R5, R6, R16 |
| 4 | 18p | Capacitor_SMD:C_0805_2012Metric | C5, C6, C9, C11 |
| 4 | MountingHole_Pad | MountingHole:MountingHole_3.2mm_M3_Pad_Via | H1, H2, H3, H4 |
| 3 | 4.7u | Capacitor_SMD:C_0805_2012Metric | C15, C21, C24 |
| 3 | USB_B_Micro | Connector_USB:USB_Micro-B_Molex-105017-0001 | J2, J3, J8 |
| 2 | 10u | Capacitor_SMD:C_0805_2012Metric | C16, C17 |
| 2 | 220R | Resistor_SMD:R_0805_2012Metric | R1, R2 |
| 2 | Conn_02x14_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x14_P2.54mm_Vertical | J4, J5 |
| 2 | RED | LED_SMD:LED_0805_2012Metric_Castellated | D1, D2 |
| 2 | SW_Push | Button_Switch_THT:SW_Tactile_SPST_Angled_PTS645Vx31-2LFS | SW1, SW2 |
| 1 | 16MHz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm_HandSoldering | Y1 |
| 1 | 2.2u | Capacitor_SMD:C_0805_2012Metric | C20 |
| 1 | 32.768KHz | Crystal:Crystal_SMD_MicroCrystal_CC8V-T1A-2Pin_2.0x1.2mm_HandSoldering | Y2 |
| 1 | 6.49K 1% | Resistor_SMD:R_0805_2012Metric | R7 |
| 1 | AP1117-33 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U3 |
| 1 | Conn_02x02_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x02_P2.54mm_Vertical | J7 |
| 1 | Conn_02x04_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x04_P2.54mm_Vertical | J9 |
| 1 | Conn_02x08_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x08_P2.54mm_Vertical | J6 |
| 1 | KSZ8081RNA | Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm | U4 |
| 1 | Micro_SD_Card | Connector_Card:microSD_HC_Hirose_DM3AT-SF-PEJM5 | J1 |
| 1 | S25FL132K0XMFI010 | Package_SO:SO-8_5.3x6.2mm_P1.27mm | U1 |
| 1 | STM32H750VBT6 | Package_QFP:LQFP-100_14x14mm_P0.5mm | U2 |
| 1 | SW_DIP_x01 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | SW3 |
It measures 63.5 × 73.7 mm and has 2 copper layers, 1.6 mm thick.
64 parts, built around the STM32H750VBT6, KSZ8081RNACA and S25FL132K0XMFI010. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the martinribelotta/h7value repository on GitHub, at the commit this page was made from: the board is proto-h750.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask martinribelotta before reusing the design.
alberto-grl/H7RTX-V2-Schematics-PCB
Schematics and PCB for a three-band direct sampling SDR. Using the internal ADC of an MCU, TX power is about 5 W. USB powered. Firmware code: https://github.com/alberto-grl/750RTX
calicopizzadelivery/sbc-development-baseboard
Baseboard for remote management of an attached SBC: K64 MCU as USB HID to the target and Ethernet to the workstation, six switched USB-A ports, isolated SPDT relays, level-shifted console, switched target power
HEAPLab/marco-ram-board
Hardware design for a STM32F7-based board with lotsa RAM
dragonlock2/kicadboards
Offsite backup for the miscellaneous KiCad boards that don't fit elsewhere
