

Hi amp
- Size
- 138 × 104 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 140
- Nets
- 116
- Pads
- 468
- Tracks, vias
- 359, 117
- Pours
- 17
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 25 Jul 2024
- Updated
- 6 Nov 2026
Overview
Hi amp is an open-source printed circuit board by marmbrus, from the marmbrus/circuits repository on GitHub. It is a 4-layer board of 138 × 104 mm with 140 parts on 116 nets, routed with 359 tracks and 117 vias.
It is built around the ESP32-S3-WROOM-1-N8, UCC27517DBVR-TP and ADS1115IDGSR, with the TPS54202DDC, BTS70021EPPXUMA1 and BSS138 among its other parts. Its parts include 27 resistors, 26 capacitors, 21 connectors, 12 ICs and 9 diodes. It belongs with the audio and music boards and the ESP32 boards of this library.
Main components
8ESP32-S3-WROOM-1-N8
SMD,25.5x18mm-40℃~+85℃ -98.2dBm 2.4GHz 20.5dBm 355mA 3V~3.6V 95mA Bluetooth5.0 ESP32-S3 Chip On-board PCB Antenna UART、SPI、I2C、I2S、USB SMD,25.5x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesUCC27517DBVR-TP
SOT-23-50℃~+125℃ 1 100uA 11ns 12ns 1V~1.2V 2.4V~2.6V 300mA 33ns 33ns 4.5V~18V 600mA Enable shutdown、Interleaved conduction protection Low Side MOSFET SOT-23-5 Gate Drivers ROHSTECH PUBLICGate DriversADS1115IDGSR
VSSOP-10-40℃~+125℃ 16 1LSB 2 2.048V 2V~5.5V 500nA 860Hz 8Hz、16Hz、32Hz、64Hz、128Hz、250Hz、475Hz、860Hz Built-in Built-in I2C Sigma-Delta Support Yes VSSOP-10 Analog to Digital Converters (ADC) ROHSTexas InstrumentsAnalog To Digital Converters (ADC)TPS54202DDC
SOT23-64.5V to 28V Input, 2A Output, EMI Friendly Synchronous Step Down ConverterTexas InstrumentsUncategorisedBTS70021EPPXUMA1
TSSOP-14-EP-150mil-40℃~+150℃ 1 2.6mΩ 21A 6V~18V Active High High Side Switch Overvoltage protection、Undervoltage lockout、Reverse voltage protection、Overcurrent Protection、Over temperature protection、Latch protection、Short-Circuit Protection TSSOP-14-EP-150mil Power Distribution Switches ROHSInfineon TechnologiesPower Distribution SwitchesBSS138
SOT-23-55℃~+150℃ 1 N-channel 1.1Ω@10V、1.2Ω@4.5V 1.2V 1.7nC@10V 17.5pF 340mA 350mW 50V 6.5pF N-Channel SOT-23 MOSFETs ROHShongjiachengMOSFETsBM04B-SRSS-TB(LF)(SN)
SMD,P=1mm-25℃~+85℃ 1 1A 1mm 1x4P 3.6mm 4 4.25mm 4P 50V 6mm Auxiliary Solder Pin Copper alloy PA SR Surface Mount,Vertical Tin UL94V-0 White SMD,P=1mm Wire To Board Connector ROHSJSTWire To Board ConnectorXGL4040-153MEC
SMD,4x4mm15uH 2.5A 3.6A 82.2mΩ Magnetic Shielded Inductor ±20% SMD,4x4mm Power Inductors ROHSCoilcraftPower Inductors
README
readme.mdPlugins
Template Setup
Preferences -> Configure Paths...
- KICAD_USER_TEMPLATE_DIR=~/workspace/circuits/templates
Component Setup
easyeda2kicad
- github
easyeda2kicad --output ~/workspace/circuits/libraries/easyeda2kicad --full --lcsc_id=...
Schematics Editor -> Preferences -> Manage Symbol Libraries...
easyeda2kicad -> circuits/libraries/easyeda2kicad/easyeda2kicad.kicad_sym
PCB Editor -> Preferences -> Manage Footprint Libraries...
easyeda2kicad -> circuits/libraries/easyeda2kicad/easyeda2kicad.pretty
Parts
140| Qty | Value | Footprint | References |
|---|---|---|---|
| 18 | LabeledTestPoint | easyeda2kicad:LabeledTestPoint | TP1, TP2, TP3, TP4, TP5, TP6, TP7, TP10, TP11, TP12, TP13, TP14, TP15, TP16, TP17, TP18 +2 |
| 16 | 01550900M | easyeda2kicad:FUSE-SMD_L9.8-W5.0_01550900M | FH1, FH2, FH3, FH4, FH5, FH6, FH7, FH8, FH9, FH10, FH11, FH12, FH13, FH14, FH15, FH16 |
| 12 | 39288020 | easyeda2kicad:CONN-TH_39288020 | CN6, CN7, CN8, CN10, CN11, CN12, CN14, CN15, CN16, CN18, CN19, CN20 |
| 7 | 100nF | Capacitor_SMD:C_0603_1608Metric | C4, C7, C10, C20, C22, C24, C26 |
| 7 | 10k | Resistor_SMD:R_0603_1608Metric | R1, R2, R3, R4, R10, R11, R12 |
| 5 | 10uF | Capacitor_SMD:C_0603_1608Metric | C6, C9, C21, C23, C25 |
| 5 | LED | LED_SMD:LED_0603_1608Metric | D1, D2, D4, D6, D8 |
| 4 | 1.5k | Resistor_SMD:R_0603_1608Metric | R15, R18, R22, R25 |
| 4 | 120 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R6, R13, R14, R21 |
| 4 | 1uF | Capacitor_SMD:C_0603_1608Metric | C15, C17, C18, C19 |
| 4 | 3.3k | Resistor_SMD:R_0603_1608Metric | R17, R20, R24, R27 |
| 4 | 39302030 | easyeda2kicad:CONN-TH_3P-P4.20_39302030 | CN5, CN9, CN13, CN17 |
| 4 | 4.7k | Resistor_SMD:R_0603_1608Metric | R16, R19, R23, R26 |
| 4 | BTS70021EPPXUMA1 | easyeda2kicad:PG-TSDSO-14_L4.9-W3.9-P0.65-LS6.0-BL-EP | U8, U9, U11, U12 |
| 4 | D_TVS | Diode_SMD:D_SMB | D3, D5, D7, D9 |
| 4 | MountingHole_Pad | MountingHole:MountingHole_3.2mm_M3_Pad_Via | H1, H2, H3, H4 |
| 4 | UCC27517DBVR | easyeda2kicad:SOT-23-5_L3.0-W1.7-P0.95-LS2.8-BR | U2, U6, U7, U10 |
| 3 | 22uF | Capacitor_SMD:C_1206_3216Metric | C8, C12, C13 |
| 3 | 428192213 | easyeda2kicad:CONN-TH_0428192214 | CN1, CN2, CN3 |
| 2 | 22uF | Capacitor_SMD:C_Elec_5x5.8 | C3, C5 |
| 2 | 73412-0110 | easyeda2kicad:ANT-SMD_73412-0110 | RF1, RF2 |
| 2 | BSS138 | Package_TO_SOT_SMD:SOT-23 | Q1, Q2 |
| 2 | KEY-SMD_B3U-1000PM | easyeda2kicad:KEY-SMD_B3U-1000PM | SW1, SW2 |
| 1 | 100k | Resistor_SMD:R_0603_1608Metric | R8 |
| 1 | 100nf | Capacitor_SMD:C_0603_1608Metric | C11 |
| 1 | 10nF | Capacitor_SMD:C_0603_1608Metric | C16 |
| 1 | 10uf | Capacitor_SMD:C_0603_1608Metric | C1 |
| 1 | 13.3k | Resistor_SMD:R_0603_1608Metric | R9 |
| 1 | 1uf | Capacitor_SMD:C_0603_1608Metric | C2 |
| 1 | 330 | Resistor_SMD:R_0603_1608Metric | R5 |
| 1 | 49.9 | Resistor_SMD:R_0603_1608Metric | R7 |
| 1 | 75pF | Capacitor_SMD:C_0603_1608Metric | C14 |
| 1 | ADS1115IDGSR | easyeda2kicad:MSOP-10_L3.0-W3.0-P0.50-LS5.0-BL | U5 |
| 1 | BM04B-SRSS-TB(LF)(SN) | easyeda2kicad:CONN-SMD_BM04B-SRSS-TB | CN4 |
| 1 | Conn_01x06 | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J1 |
| 1 | ESP32-S3-WROOM-1 | RF_Module:ESP32-S3-WROOM-1 | U1 |
| 1 | TPS54202DDC | Package_TO_SOT_SMD:SOT-23-6 | U3 |
| 1 | TPS73733DCQ_C5220270 | easyeda2kicad:SOT-223-6_L6.5-W3.5-P1.27-LS7.0-BR | U4 |
| 1 | XGL4040-153MEC | easyeda2kicad:IND-SMD_L4.0-W4.0_XAL4040-103 | L1 |
More from marmbrus/circuits
12- 4 layers100 × 91.4 mm

- 4 layers138 × 125 mm

- 4 layers68.8 × 135.2 mm

- 4 layers125.5 × 154.5 mm

- 4 layers295.1 × 12 mm

- 4 layers70 × 82 mm

- 4 layers70 × 62 mm

- 4 layers94 × 74 mm

- 4 layers94 × 74 mm

- 4 layers121.5 × 154.3 mm

- 4 layers70 × 45 mm

- 4 layers63 × 63 mm

Similar boards
- 4 layers212 × 116 mm

Eswitch simple
dpeckham/eswitch
8-channel ESP32-S3 + PROFET+2 (BTS7008-1EPP) 12V load switch with 3-position ATO fuse bypass, KiCad 10, script-generated
230 parts - 4 layers65 × 66 mm

Main V2
MCiuzelis/LituanicaX_AutonomousCarPlatform
Mechanical and electrical design files for the LituanicaX autonomous RC car: a Raspberry Pi 5–based robot that navigates a cone-track circuit using a depth camera.
69 parts - 2 layers137 × 84 mm

ESP32-Geiger Counter
AronASzucs/Avalanche32
Handheld ESP32-S3 Geiger counter with a firmware-regulated 400 V boost, SBM-20 tube, USB-C charging and OLED display.
89 parts3 - 4 layers100 × 90 mm

- 4 layers53.2 × 53.2 mm

Smart lcc
variegated-coffee/open-lcc-board
Schematics and PCB files for the Open LCC hardware
117 parts30CERN-OHL-P-2.0 - 6 layers69 × 54 mm

Open control board
variegated-coffee/all-purpose-espresso-controller
Espresso electronics are usually proprietary affairs with little to no expandability. The purpose of this project is to give everyone an open source alternative with lots of features and flexibility.
201 parts14CERN-OHL-P-2.0 - 2 layers85 × 85 mm

Cube display
atomic14/cube-display
I'm currently testing the first set of PCBs. There will be updates as I find issues!
73 parts2 - 4 layers100 × 100 mm

Antenna top cap v2
proveskit/antenna-board
The PROVES Kit Antenna Boards! By convention the Z+ Top Cap of the satellite.
74 partsCERN-OHL-W-2.0
Questions
How big is the Hi amp PCB?
It measures 138 × 104 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Hi amp use?
140 parts, built around the ESP32-S3-WROOM-1-N8, UCC27517DBVR-TP, ADS1115IDGSR and TPS54202DDC. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Hi amp KiCad files?
From the marmbrus/circuits repository on GitHub, at the commit this page was made from: the board is leds/hi_amp/hi_amp.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Hi amp design in my own project?
Its repository states no licence, so its author keeps all rights: ask marmbrus before reusing the design.