Skip to the content
2 layers219.1 × 66.7 mmStonehenge30, the printed circuit board in 3D

This repository is warehouse of my keyboard architecture.

Size
219.1 × 66.7 mm
Copper layers
2
Thickness
1.6 mm
Parts
80
Nets
51
Pads
531
Tracks, vias
665, 50
Pours
2
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
18 Dec 2018
Updated
17 Aug 2024

Overview

Stonehenge30 is an open-source printed circuit board by marksard, from the marksard/Keyboards repository on GitHub, published under the MIT licence. It is a 2-layer board of 219.1 × 66.7 mm with 80 parts on 51 nets, routed with 665 tracks and 50 vias.

Its parts include 30 diodes, 30 switches, 4 connectors and 1 IC. It belongs with the keyboards and input boards and the AVR (ATmega, ATtiny) boards of this library.

README

README.md

Keyboards

This repository is warehouse of my keyboard architecture.

About Firmware

Release firmware
Keymap editing web service REMAP

WARNING

Note that for these keyboards, the design is older and also less likely to support the latest firmware and architecture.
Also, KICAD files may be incomplete, they are not going to be perfect.

Rhymestone

img

About Rhymestone

The Rhymestone is 40-key (40%) ortholinear keyboard. It is based on The crkbd and The Helix keyboard. Thank you so much makoto kurauchi-san and foostan-san.😊

Build guide
Firmware
Hardware data

Treadstone48

rev1
img

rev2
img

About Treadstone48

The Treadstone48 is 47 or 48-key (50%) Symmetric staggered keyboard. It is based on the Rhymestone. Therefore, The Rhymestone can connect to the Treadstone48 as Numpad or lefthand keyboard. (rev1 only)

This Symmetrical Staggered is designed to be easy to use in a natural posture and easy for your fingers to reach.
And more one topic, this key arrangement can use general ansi 104 keycaps.

Build guide (rev.2)

Build guide
Build guide (En)
Firmware
Hardware data
About Treadstone48
Case design sample

Stonehenge30 (deprecated)

img

About Stonehenge30

The Stonehenge30 is 30-key (30%) Symmetric staggered keyboard. It is based on the Treadstone48. And it is thumb-less (not use thumb) keyboard of prototype.

Build guide
Firmware
Hardware data
About Stonehenge30
Case design sample

Treadstone32

rev1
img

lite
img

About Treadstone32

The Treadstone32 is 32-key (30%) Symmetric staggered keyboard. It is based on the Treadstone48 and the Stonehenge30.
This keyboard is removing dedicated modifire-key from the Treadstone48 for more compact. But 2 thumb-key is left same as Treadtone48.

Build guide (lite)
Build guide

Build guide (En)
Firmware
Hardware data
About Treadstone32

Treadstone60

img

About Treadstone60

The Treadstone60 is 59-62key (60%) Symmetric staggered keyboard. It is based on the Treadstone48 and the Treadstone32.

Build guide

Firmware
About Treadstone60

Leftover30

img

About Leftover30

The Leftover30 is 34-36key (30%) Row staggered keyboard. This project was created by marksard, yohewi and hdbx.

Build guide

Firmware

Troubleshooting

Troubleshooting

Parts

80
QtyValueFootprintReferences
30Dkbd:D3_SMD_frontD1, D2, D10, D11, D12, D13, D14, D15, D16, D17, D18, D19, D20, D21, D22, D23 +14
30SW_PUSHkbd:MX-Alps-Choc-1U-NoLEDSW1, SW2, SW10, SW11, SW12, SW13, SW14, SW15, SW16, SW17, SW18, SW19, SW20, SW21, SW22, SW23 +14
8kbd:LEGO_HOLE_2.4, , , , , , ,
3Conn_01x03kbd:StripLED_backJ2, J3, J4
2kbd:LEGO_HOLE2,
1LOGOkbd:Stonehenge30_logo2_backG***
1LOGOkbd:Stonehenge30_logo1G***
1OLEDkbd:OLEDJ1
1ProMicrokbd:ProMicro_v2_frontU1
1RSWkbd:ResetSWRSW1

The 78 most common of 80 parts.

More from marksard/Keyboards

3
  • 2 layers281 × 76.2 mmTreadstone48, the printed circuit board in 3D

    Treadstone48

    marksard/Keyboards

    This repository is warehouse of my keyboard architecture.

    125 parts193MIT
  • 2 layers95.3 × 95.3 mmRhymestone, the printed circuit board in 3D

    Rhymestone

    marksard/Keyboards

    This repository is warehouse of my keyboard architecture.

    88 parts193MIT
  • 2 layers198.8 × 75.6 mmTreadstone32, the printed circuit board in 3D

    Treadstone32

    marksard/Keyboards

    This repository is warehouse of my keyboard architecture.

    85 parts193MIT

Similar boards

  • 2 layers54.6 × 89.5 mmPicoRX, the printed circuit board in 3D

    PicoRX

    dawsonjon/PicoRX

    Build a SDR SW/MW/LW Receiver with a Raspberry Pi Pico

    80 parts556
  • 2 layers130.4 × 76.6 mmGb stream cart, the printed circuit board in 3D

    Gb stream cart

    Staacks/gbinterceptor

    Capture or stream Game Boy gameplay footage via USB without modifying the Game Boy.

    80 parts542
  • 2 layers100 × 100 mmEleLab v2 Bus100, the printed circuit board in 3D

    EleLab v2 Bus100

    Chrismettal/EleLab_v2

    Cheap DIY lab system for hobbyists and the tinkering folk

    80 parts531GPL-3.0
  • 2 layers59.6 × 109.5 mmKivu12, the printed circuit board in 3D

    Kivu12

    ohmtech-rdi/eurorack-blocks

    Software to Hardware Prototyping for Eurorack using C++, Max/Gen~ or Faust

    80 parts410
  • 2 layers137.9 × 92.7 mmErgoTravel, the printed circuit board in 3D

    ErgoTravel

    jpconstantineau/ErgoTravel

    A Portable Ergonomic Split Keyboard inspired from the ErgoDox, Let's Split and Minidox

    80 parts284MIT
  • 2 layers99.1 × 99.7 mmRC6502 General Video Adapter, the printed circuit board in 3D

    RC6502 General Video Adapter

    tebl/RC6502-Apple-1-Replica

    An expandable SBC-version of the Apple 1 computer, easy to get started with and lot of cool stuff that can be added to it!

    80 parts193GPL-3.0
  • 2 layers226.9 × 108.5 mmMikecinq, the printed circuit board in 3D

    Mikecinq

    mikeholscher/zmk-config-mikecinq

    ZMK Config + Files

    80 parts126
  • 2 layers124.5 × 132.1 mmInterface osi, the printed circuit board in 3D

    Interface osi

    osiweb/unified_retro_keyboard

    Project to provide keyboard replacements for various classic computers, as well as classic ASCII keyboard

    80 parts122

Questions

How big is the Stonehenge30 PCB?

It measures 219.1 × 66.7 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Stonehenge30 use?

80 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Stonehenge30 KiCad files?

From the marksard/Keyboards repository on GitHub, at the commit this page was made from: the board is stonehenge30/pcb/rev0.1/Stonehenge30.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Stonehenge30 design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).