2 layers99.1 × 55.4 mm
ESP32 Plotter Controller
MarkJB/ESP32_Plotter_Controller
An ESP32/TMC2130 based 2 axis controller designed for pen plotters
38 parts9MIT
2 layers99.1 × 55.4 mm
ESP32 Plotter Controller revB1 unrouted
MarkJB/ESP32_Plotter_Controller9An ESP32/TMC2130 based 2 axis controller designed for pen plotters
- Size
- 99.1 × 55.4 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 53
- Nets
- 78
- Pads
- 252
- Tracks, vias
- 131, 2
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 20 Feb 2021
- Updated
- 30 Nov 2022
Overview
ESP32 Plotter Controller revB1 unrouted is an open-source printed circuit board by MarkJB, from the MarkJB/ESP32_Plotter_Controller repository on GitHub, published under the MIT licence. It is a 2-layer board of 99.1 × 55.4 mm with 53 parts on 78 nets, routed with 131 tracks and 2 vias.
It is built around the CH340C, ESP32-WROOM-32D and TMC2130-LA, with the XL1509-3.3, AMS1117-3.3 and B5819W among its other parts. Its parts include 19 connectors, 11 capacitors, 6 resistors, 6 ICs and 2 diodes. It belongs with the ESP32 boards of this library.
Main components
6
CH340C
SOP-16-20℃~+70℃ 2Mbps 3.3V、5V 50uA 7mA Transceiver USB 2.0 SOP-16 USB Converters ROHSWCH (Nanjing Qinheng Microelectronics)USB Converters
ESP32-WROOM-32D
-- WiFi Modules ROHSEspressif SystemsWiFi Modules
TMC2130-LA
QFN-36-EP(5x6)QFN-36-EP(5x6) Motor Driver ICs ROHSTRINAMIC Motion Control GmbHMotor Driver ICs
XL1509-3.3
SOP-8-40℃~+125℃@(TJ) 1 150kHz 2A 2mA 3.3V 4.5V~40V Buck Buck Built-in Fixed No SOP-8 DC-DC Converters ROHSUMWDC-DC Converters
AMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
B5819W
SOD-123-55℃~+125℃ 1.5A 1mA@40V 25A 40V 600mV@1A Standalone SOD-123 Schottky Diodes ROHSMDDSchottky Diodes
README
README.mdESP32 Plotter Controller PCB
Released under an MIT licence, no warranty implied or given, use at own risk etc etc.
This is a two axis stepper controller based on the ESP32 and TMC2130 stepper drivers. It is intended to be used with drawing machines and plotters.
See https://github.com/MarkJB/TMC429_Daughterboard_for_ESP32_Plotter_Controller for the TMC429 (Hardware stepper driver contoller) daughter board for this board (plugs into the two stepper motor driver sockets and provides an extra axis and hardware acceleration control.
Firmware https://github.com/MarkJB/Grbl_Esp32 (This is a Fork of Grbl_Esp32, if its out of date, you probably only need the config file from this fork). Tested with standard and corexy kinematics and a solenoid/relay for the spindle.
First board revision A (aka 'Diamiond Chimp'), this board revision B (aka Emerald Dingo)
Parts
53| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | MountingHole_3.2mm_M3 | MountingHole:MountingHole_3.2mm_M3 | H1, H2, H3, H4 |
| 2 | 0.1uF | Capacitor_SMD:C_0603_1608Metric | C8, C11 |
| 2 | 100 | Resistor_SMD:R_0603_1608Metric | R1, R2 |
| 2 | 100nF | Capacitor_SMD:C_0603_1608Metric | C4, C5 |
| 2 | 10K | Resistor_SMD:R_0603_1608Metric | R3, R4 |
| 2 | 22uF 10v | Capacitor_Tantalum_SMD:CP_EIA-3216-18_Kemet-A | C9, C10 |
| 2 | 47uF 35V | Capacitor_SMD:CP_Elec_6.3x5.7 | C6, C7 |
| 2 | 5.1k | Resistor_SMD:R_0603_1608Metric | R5, R6 |
| 2 | B5819W | Diode_SMD:D_SOD-123 | D1, D2 |
| 2 | TMC2130 | custom:StepstickTMCv2 | U2, U3 |
| 1 | 180uF 35v | Capacitor_SMD:CP_Elec_6.3x7.7 | C3 |
| 1 | 1uF | Capacitor_SMD:C_0805_2012Metric | C2 |
| 1 | 470uF 35v | Capacitor_SMD:CP_Elec_10x10 | C1 |
| 1 | 5V Aux | Connector_JST:JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | J3 |
| 1 | 68uH | Inductor_SMD:L_12x12mm_H6mm | L1 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U6 |
| 1 | ARM JTAG 10pin | Connector_PinSocket_2.54mm:PinSocket_2x05_P2.54mm_Vertical | J1 |
| 1 | Aux Port (I2C) | Connector_JST:JST_PH_S6B-PH-K_1x06_P2.00mm_Horizontal | J16 |
| 1 | Aux Port (SPI) | Connector_JST:JST_PH_S8B-PH-K_1x08_P2.00mm_Horizontal | J6 |
| 1 | BOOT | custom:K2-1107ST | SW2 |
| 1 | CH340C | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U5 |
| 1 | E-Stop | Connector_JST:JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | J18 |
| 1 | ESP32-WROOM-32D | RF_Module:ESP32-WROOM-32 | U1 |
| 1 | LOGO | custom:emerald_dingo_150 | G2 |
| 1 | LOGO | custom:emerald_dingo_400 | G1 |
| 1 | Micro_SD_Card | custom:HK-TF01A | J8 |
| 1 | Neo Pixel LEDs | Connector_JST:JST_PH_S3B-PH-K_1x03_P2.00mm_Horizontal | J14 |
| 1 | Pen Direction | Connector_JST:JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | J15 |
| 1 | Pen Lift | Connector_JST:JST_PH_S3B-PH-K_1x03_P2.00mm_Horizontal | J10 |
| 1 | Power | Connector_BarrelJack:BarrelJack_Horizontal | J2 |
| 1 | RESET | custom:K2-1107ST | SW1 |
| 1 | USB_C_Receptacle_USB2.0 | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J17 |
| 1 | Vin Aux | Connector_JST:JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | J4 |
| 1 | Vselect | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J11 |
| 1 | X Limit | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J7 |
| 1 | X Limit Switch | Connector_JST:JST_PH_S3B-PH-K_1x03_P2.00mm_Horizontal | J5 |
| 1 | X Motor | Connector_JST:JST_PH_S4B-PH-K_1x04_P2.00mm_Horizontal | J12 |
| 1 | XL1509 | Package_SO:SO-8_3.9x4.9mm_P1.27mm | U4 |
| 1 | Y Limit | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J9 |
| 1 | Y Limit Switch | Connector_JST:JST_PH_S3B-PH-K_1x03_P2.00mm_Horizontal | J19 |
| 1 | Y Motor | Connector_JST:JST_PH_S4B-PH-K_1x04_P2.00mm_Horizontal | J13 |
Questions
How big is the ESP32 Plotter Controller revB1 unrouted PCB?
It measures 99.1 × 55.4 mm and has 2 copper layers, 1.6 mm thick.
What parts does the ESP32 Plotter Controller revB1 unrouted use?
53 parts, built around the CH340C, ESP32-WROOM-32D, TMC2130-LA and XL1509-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ESP32 Plotter Controller revB1 unrouted KiCad files?
From the MarkJB/ESP32_Plotter_Controller repository on GitHub, at the commit this page was made from: the board is ESP32_Plotter_Controller_revB1_unrouted.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the ESP32 Plotter Controller revB1 unrouted design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
More from MarkJB/ESP32_Plotter_Controller
1Similar boards
- 4 layers89 × 58 mm
HALMET
hatlabs/HALMET-hardware
Hat Labs Marine Engine & Tank interface hardware design files
227 parts8CC-BY-4.0 - 4 layers89 × 58 mm
- 2 layers240 × 174.3 mm
Final H00 panelicad pcb
Vedatori/Time-O-Mat
Addressable LED clock kit aimed for usage in STEM education. The ultimate solution to time telling...
312 parts7 - 2 layers60 × 100 mm
PaLampa MoBo H00
Vedatori/PaLampa
Mechanickou část lze rozdělit na dvě hlavní části - spodní krabici a horní lampu. Vnější části krabice jsou vyřezány z překližky na laserové řezačce a obsahují zámkové západky.
80 parts4 - 2 layers99.5 × 90.5 mm
- 2 layers102 × 102 mm
- 4 layers62.9 × 88.6 mm
Bit block
Citrullin/Sovereign_Bunny_Stack
From web 3 unicorn fantasy to federated web 2.5 reality.
169 parts4 - 2 layers40 × 98 mm
