
Encoder
byrantech/laptop
anyon_e, a highly integrated, high end, open source laptop. Attempt the impossible.

USB type C connector board for TMK Alt HHKB board =================================================
Usb type c hhkb is an open-source printed circuit board by manisteinn, from the manisteinn/usb-type-c-hhkb repository on GitHub. It is a 2-layer board of 12.9 × 12.4 mm with 7 parts on 16 nets, routed with 89 tracks and 11 vias.
Its parts include 5 connectors and 2 resistors.
Notice: This project probably won't receive any further updates, hasu now has a usb-type-c version of his controller board and I don't use my HHKB all that much anymore.
I've added the FreeCAD design files for my related additions to the hhkb-alt-cad directory. These were made in FreeCAD 0.17 a couple of years ago (never got around to release them until now) but seem to work in the current version. Feel free to submit an issue if needed, it might be a quick fix.
I ordered SLA printed covers and switch caps a few years ago from DirtySLA.
See the output/order/combined subdirectory for cost-optimized models (they didn't seem to mind attached duplicates) as well as a FCMacro for cost/volume calculation.
I later did a PCB version of the covers and ordered those from OSHpark. Recently I got into resin casting, so after discovering the severe yellowing of the SLA printed parts due to UV exposure I decided to make a mold for the slide switch caps and cast copies of them.
Image gallery with more details.
FreeCAD 0.17+ with lattice2 addon (install with tools>addon manager) 0.16 was used for solid PCB import (pcb workbench), I had issues on 0.17
KiCAD v4+ for PCB covers
Origin is PCB top left corner, top surface.
Rear plate port cutouts (bodies) use lattice2 placements, covers use the x-value of those placements for offset and can thus be edited in place.
Rear plate height above PCB is the minimum clearance below the upper case ribs, check their location if extending beyond that. Also check the top PCB clearance if extending them inward.
Switch cover is centered, consider the 2mm symmetrical switch travel.
Parts can't be used directly for lattice2 placements, hence the clones
SS22SDH2 switch
SLP3-150-100-R lightpipe
DX07S024JJ2R1300 usb-c connector
HHKB controller board models included with hasu's permission
CC0 for all my contributions
Replaces the Mini-USB connector of a tmk HHKB controller board with a usb type C connector (JAE DX07S024JJ2) mounted on a small PCB. No case modification required, just remove existing connector, clean solder pads and solder this board in place. CC1 and CC2 have 5.1Kohm pulldown (UFP Rd) in order to be usable by type-C host (DFP) devices. See specification for details
Kicad origin point is the same as tmk HHKB board (useful for gerber overlay) Fits rev A-G (tiny overlap on revA C5 footprint), isolate second VUSB pad on F,G USB-C connector footprint modified for oshpark (they don't support overlapping drill hits), might need changes for other fabricators.
Rev 3
Rev 2
git commands for cloning submodules (usb-type-c-kicad-lib, usb-type-c.pretty):
git clone https://github.com/manisteinn/usb-type-c-hhkb
cd usb-type-c-hhkb
git submodule update --initor
git clone --recursive https://github.com/manisteinn/usb-type-c-hhkb| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | R5.1K | Resistors_SMD:R_0603 | R1, R2 |
| 1 | D+ | pins:PIN_1 | P2 |
| 1 | D- | pins:PIN_1 | P3 |
| 1 | GND | pins:PIN_1 | P1 |
| 1 | USB_TYPE_C | usb-type-c:JAE-DX07S024JJ2-oshpark-cutpads | J1 |
| 1 | VCC | pins:PIN_1_SQUARE | P4 |

byrantech/laptop
anyon_e, a highly integrated, high end, open source laptop. Attempt the impossible.



AxxAxx/AxxSolder
STM32 Based soldering station for JBC cartridges, 9-24 VDC and USB-PD power


jamro/tiny-engineer
A small desktop robot that brings an AI coding assistant to life, physically acting out when it reads files, thinks, writes code, and finishes work.

hoglet67/RGBtoHDMI
Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

It measures 12.9 × 12.4 mm and has 2 copper layers, 1.6 mm thick.
7 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the manisteinn/usb-type-c-hhkb repository on GitHub, at the commit this page was made from: the board is usb-type-c-hhkb.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask manisteinn before reusing the design.