Skip to the content
2 layers25.2 × 25.2 mmUsb uart m200, the printed circuit board in 3D

Klipper port for the Zortrax m200+

Size
25.2 × 25.2 mm
Copper layers
2
Thickness
1.6 mm
Parts
17
Nets
33
Pads
89
Tracks, vias
126, 18
Pours
1
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
27 Jan 2026
Updated
13 May 2026

Overview

Usb uart m200 is an open-source printed circuit board by mandraga, from the mandraga/klipper4m200 repository on GitHub. It is a 2-layer board of 25.2 × 25.2 mm with 17 parts on 33 nets, routed with 126 tracks and 18 vias.

It is built around the CY7C65213-28PVXI and USBLC6-2SC6. Its parts include 4 resistors, 3 capacitors, 3 ICs, 2 diodes and 2 connectors. It belongs with the interfaces and adapters boards of this library.

Main components

2

README

README.md

klipper4m200

A replacement firmare for the Zortrax M200+ 3D printer.

This firmware is based on Debian/Armbian and allows to install klipper on the m200+. There is no comming back once the microcontroller is flashed.

Building steps

Update the submodules, or get them separately.

  • Armbian build
  • u-boot
  • sunxi-tools

Access the internal single board computer

You need:

  • a serial port on the UART0 J5 connector for the u-boot and Linux serial console.
  • a special USB-A to USB-A cable with no 5V connexion to be able to use the FEL mode.

At boot, press '2' on the serial console, it will start in FEL mode. You should see this on "dmesg -w":

text
ID 1f3a:efe8 Allwinner Technology sunxi SoC OTG connector in FEL/flashing mode

Then, using sunxi-tools, you can upload a uboot image like this:

text
sunxi-tools$ sudo ./sunxi-fel uboot ../u-boot/u-boot-sunxi-with-spl.bin

It starts uboot and you can browse files and dump data.

Then you can use this uboot prompt to load the dtb and the kernel, then boot Armbian from the usb stick.

Once in Linux, you can:

  • dump the original disk image on the usb stick.
  • dump the vendor u-boot env
  • write your u-boot-env
  • write u-boot-dtb.bin to the FAT16 partition

Download the image

Compile u-boot with build_m200.sh from the bootstage folder in this repo, run it in the u-boot fork repo. Create an Armbian full image using the lime-A33 board using the armbian_build repo. DD it on /dev/sdx2 where sdx is your usb stick (or edit uboot command to use sdx1 instead). Do not forget to include linux headers and to enable the touchscreen (see linux.md). In armbian_build:

text
./compile.sh INSTALL_HEADERS=yes

At first boot from FEL mode

Look at usb.md or progress.md to see how to load the kernel from u-boot.

Install the new u-boot env and mainline uboot binary on the emmc such as to automaticly boot from the USB drive. The original emmc is not that much altered, only the env. You can resore it with a backup file or in vendor u-boot console.

Get the network

  • On version 2.1, Linux should detect the ethernet usb adapter on the USB port. Version 2.1 has two usb ports.
  • On version 1.1, the USB0 trace must be cut and a posrt soldered to boot from USB. You need to connect some ethernet adapter to an usb hub. Version 1.1 has only one USB port on the front.

Then connect your printer to the network.

Install klipper

Follow this tutorial https://travis90x.altervista.org/armbian-first-boot-and-install-klipper/

text
git clone https://github.com/dw-0/kiauh.git
./kiauh/kiauh.sh

It will install everything klipper related and build the firmware.

Flash the microcontroller and start Klipper

See the Readme in the MCU folder, you need an ST-Link programmer to mass erase the chip.

Klipper config

rpanfili has already configured klipper for zortrax M200 but for an SK200 MCU board. However the geometry and a lot of stock parameters are already in his configuration.

Zortrax has published a Marlin port for the M200. By looking at the commits, and the work done in the zmxxxp-re repository, I could find the MCU pinouts in "pins_ZORTRAX_M200.h" to configure the klipper MCU firmware. Be carefull whith the X, Y axis stops, they are not the same depending on verison 1.1 or 2.2.

The configuration in this repo is the rpanfili one, modified for the Zortrax MCU board instead of the SK1.4.

Calibration and tuning

https://ellis3dp.com/Print-Tuning-Guide/ https://github.com/OrcaSlicer/OrcaSlicer/wiki/Calibration

The ZABS spec https://cf.zortrax.com/wp-content/uploads/2020/09/Z-ABS_2_Technical_Data_Sheet_eng.pdf

PID tuning at different fan speeds and in GCODE: https://www.youtube.com/watch?v=USvg6D0cXE4

Start printing

If everything went fine, you can connect to Mainsail or Fluid web interfaces copy the klipper configuration and start configuring the bed level. Then, because it is klipper, you must run calibration towers with your filaments and tweak orcaslicer prior to begin printing. That's what's lost in the process but you have control and can use any filament.

About

This work lasted from october 2025 to April 2026 and was much more difficult than planed, given that the device tree of this thing is really complex, the EMMC is really touchy, and the screen had no driver. The boot process led to 4 bricks, and needed resoldering a new programmed EMMC to save the boards. Since then, I tryed to port an ezeetab 96Q10 A-33 Andorid tablet to linux and it was quicker (a week) and also helped to progress on this project.

Parts

17
QtyValueFootprintReferences
21kResistor_SMD:R_0805_2012MetricR4, R5
222kResistor_SMD:R_0805_2012MetricR1, R2
2LEDLED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolderD1, D2
2MountingHoleMountingHole:MountingHole_3.2mm_M3_DIN965_Pad_TopBottomH1, H2
10.1µF10VCapacitor_SMD:C_0805_2012MetricC4
11µFCapacitor_SMD:C_0805_2012MetricC1
11µF10VCapacitor_SMD:C_0805_2012MetricC3
12059-301_998-4032059-301_998-403:P-2059-301_998-403X1
1CY7C65213-28PVXIPackage_SO:SSOP-28_5.3x10.2mm_P0.65mmU1
1Conn_01x02_SocketConnector_Molex:Molex_PicoBlade_53047-0210_1x02_P1.25mm_VerticalJ1
1MIC5317-3.3xM5Package_TO_SOT_SMD:SOT-23-5U2
1USBLC6-2SC6Package_TO_SOT_SMD:SOT-23-6U4
1USB_C_Plug_USB2.0Connector_USB:USB_C_Receptacle_G-Switch_GT-USB-7010ASVP1

More from mandraga/klipper4m200

1
  • 2 layers16.7 × 16.2 mmFel mode adapter, the printed circuit board in 3D

    Fel mode adapter

    mandraga/klipper4m200

    Klipper port for the Zortrax m200+

    5 parts2

Similar boards

  • 2 layers363.7 × 103.4 mmXfm2-ui board, the printed circuit board in 3D

    Xfm2-ui board

    bendecaf/xfm2-pcbs

    PCBs for the excellent FPGA synth projects XFM2 and XVA1.

    95 parts22GPL-3.0
  • 2 layers60 × 63 mmATMEGA328P AU BASE CYUSB v1.0, the printed circuit board in 3D

    ATMEGA328P AU BASE CYUSB v1.0

    kgsully/MCU.ATMEGA328P-AU-Base

    Base Schematic and PCB for ATMEGA328P-AU w/ USB-UART Bridge

    52 parts1
  • 2 layers60 × 63 mmESP32 BASE CYUSB v1.3, the printed circuit board in 3D

    ESP32 BASE CYUSB v1.3

    kgsully/MCU.ESP32-Base

    Base Schematic and PCB for ESP32 WROOM w/ USB-UART Bridge

    55 parts1
  • 2 layers181.1 × 95.9 mmCombined branches, the printed circuit board in 3D

    Combined branches

    TJREVERB/reverb_interface

    Interface board rework, moved from Eagle to Kicad

    140 parts
  • 2 layers44.5 × 16.3 mmUSB C Rial Pro, the printed circuit board in 3D

    USB C Rial Pro

    akowalczyk18/Kicad

    pcb projects

    33 parts5
  • 4 layers16.9 × 119.4 mmOrbit, the printed circuit board in 3D

    Orbit

    earthtojake/text-to-cad

    Design physical products with AI

    182 parts26kMIT

Questions

How big is the Usb uart m200 PCB?

It measures 25.2 × 25.2 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Usb uart m200 use?

17 parts, built around the CY7C65213-28PVXI and USBLC6-2SC6. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Usb uart m200 KiCad files?

From the mandraga/klipper4m200 repository on GitHub, at the commit this page was made from: the board is pcb/usb_uart_m200/usb_uart_m200.kicad_pcb and its schematic pcb/fel_mode_adapter/fel_mode_adapter.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Usb uart m200 design in my own project?

Its repository states no licence, so its author keeps all rights: ask mandraga before reusing the design.