
Led head lite
LukeRJamieson/long-range-remote
A hand-held universal IR remote with far more range than a normal one. A head of 66 narrow-beam (±5°) SFH 4545 emitters sits at the front of a 107 × 52 × 170 mm block. Behind it are:

A hand-held universal IR remote with far more range than a normal one. A head of 66 narrow-beam (±5°) SFH 4545 emitters sits at the front of a 107 × 52 × 170 mm block. Behind it are:
Control lite is an open-source printed circuit board by LukeRJamieson, from the LukeRJamieson/long-range-remote repository on GitHub. It is a 2-layer board of 82 × 52 mm with 31 parts on 23 nets, routed with 189 tracks and 6 vias.
It is built around the AOD424 and IPD80P03P4L-07. Its parts include 9 resistors, 6 capacitors, 6 switches, 3 transistors and 3 connectors.
A hand-held universal IR remote with far more range than a normal one. A head of 66 narrow-beam (±5°) SFH 4545 emitters sits at the front of a 107 × 52 × 170 mm block. Behind it are:
Everything is menu driven from the screen, or from a phone over Wi-Fi.
There are two boards, both within JLCPCB's cheapest 100 × 100 mm tier:
| Board | Size | What's on it |
|---|---|---|
| LED head | 99.8 × 44.8 mm, R3 corners | 66 × SFH 4545 (14 × 5 grid, corners left for the M3 holes) in 33 strings of 2, one 24 Ω 1206 resistor per string |
| Control | 82 × 52 mm | D-pad + SELECT + BACK (six 6 mm keys, straight to ESP32 GPIOs), the ESP32-switched power gate for the AA pack, the LED switch (a logic-level MOSFET driven straight from a GPIO), the pack-voltage divider, display and LED-head connectors |
KiCad 7 format; it opens in KiCad 7, 8 or 9.
FRONT top deck (lid) BACK
┌──────────────┐ 10-way ribbon ┌────────────────────────┐ 16-way ribbon ┌──────────────────────┐
│ LED HEAD │◄════════════════│ CONTROL BOARD 82 x 52 │══════════════►│ Waveshare │
│ 99.8 x 44.8 │ J1 ↔ J5 │ D-pad, SELECT, BACK │ J2 ↔ header │ ESP32-S3-RLCD-4.2 │
│ 66×SFH 4545 │ odd = LED_PWR │ power gate (back) │ │ (own 18650, USB-C) │
│ 33 × 24 Ω │ even = LED_RTN │ LED switch (back) │ └──────────────────────┘
└──────────────┘ └────────────────────────┘
▲ J1 (XH): 4 × AA NiMH holder, under the display| Strings | 33 × (2 LEDs + 24 Ω) straight off the AA pack |
| LED current per string | 100 mA on fresh cells (5.4 V), 75–83 mA for most of the discharge (4.8–5.0 V), ~58 mA nearly flat (4.4 V) |
| LED current, total | ≤ 3.3 A peak, ~0.87 A average while sending (C1/C2 supply the peaks) |
| Power | 4 × AA NiMH in a Keystone 2478 holder → J1 → P-FET power gate driven by the ESP32 (no switch). Display: its own 18650 |
| LED switching | One low-side AOD424 (DPAK, fully on at 2.5 V) driven straight from GPIO17 through R6 47 Ω; the power gate (ARM) powers the LEDs |
| Battery level | Pack ÷ 2 on GPIO1, and the screen's 18650 on GPIO4 |
| Parts cost | $75.08 AUD ex GST + US$6.21 at Digi-Key/Mouser, $7.15 at Core Electronics (plus the display board and AA cells) |
AA nn% any time and
AA out with no cells in.LED_POWER_PCT). LED current falls in proportion, the
signal the receiver sees by −4.6 / −10.8 dB (range ~×0.6 / ×0.3 on the same receiver noise floor,
roughly; check it on your TV). Handy for close range and for saving the cells.AA nn% (or AA out) and the screen's own battery
(scr nn%). Below 4.6 V it says "AA cells low". Below 4.4 V at rest it stops sending ("AA cells
flat"): that is 1.1 V a cell, flat for NiMH. Q2's gate drive comes from the ESP32's 3.3 V, so the LED
switch works the same right down to that point.LED_DUTY_MAX_PCT), whatever a code or .ir file asks for: on
fresh cells the strings peak at ~110 mA, so the average must stay well under the SFH 4545's 100 mA
DC rating.LED_ARM_SETTLE_MS (30 ms)
after ARM, once VBAT is up, and checks the pack before every frame. A held key stops after 15 s. It is still a strong IR source, so don't look into the
head up close.| Path | What it is |
|---|---|
docs/Long-Range_Remote_Lite_User_Guide.pdf | User guide: setup, using the remote, batteries, the web page, home Wi-Fi, building the housing, troubleshooting |
led_head_lite/led_head_lite.kicad_pro | LED head project (schematic + PCB) |
control_lite/control_lite.kicad_pro | Control board project (schematic + routed PCB) |
gerbers/*_jlcpcb.zip | Gerber + drill zips, ready to upload to JLCPCB |
bom/lite_digikey_bom.csv | BOM with refs, prices and stock |
bom/lite_digikey_upload.csv | Digi-Key BOM-manager upload |
bom/lite_core_electronics.csv | Display ribbon and header (Core Electronics) |
firmware/LongRangeRemote/ | Universal remote firmware: TVs, AV receivers, set-top boxes, soundbars, projectors, hi-fi, air-cons..., phone web remote, idle sleep. See its README |
firmware/sd_card/irdb.bin | The IR code database (~6,800 remotes). Copy it to the SD card: all codes live on the card, not in the firmware |
firmware/sd_card/wifi.example.txt | Example of wifi.txt, the home Wi-Fi file on the card. The remote creates and updates wifi.txt itself (Menu → Wi-Fi network); this is for setting it on a PC |
firmware/bringup/bringup.ino | Bring-up firmware: keys, NEC transmit, LED arming, battery voltage |
previews/*_front.png, *_back.png, *_schematic.png | Both sides of each board and the schematics |
previews/*_3d_*.png | 3D renders of both boards with their components (front, back, three-quarter views) |
pdf/ | Printable PDFs: *_schematic.pdf, and *_pcb.pdf with top/bottom copper, top/bottom assembly and a 1:1 page to print at 100 % for checking fit |
housing/ | 3D-printable housing (Prusa MINI): STEP for Fusion 360, print-ready STLs, parametric CadQuery source. See housing/README.md |
tools/ | Generators (see "Regenerating"). tools/bin/ is where Freerouting goes if you re-autoroute (not included: 64 MB) |
sim/control_lite_sim.py | ngspice simulations of the control board + LED head: cell insertion, power-gate turn-on/off, 38 kHz drive, switching transients over the ribbon, worst cases (needs ngspice) |
The _lite in the board and file names is historical: this is the only version.
Front (facing up through the lid): the six keys and nothing else.
Back (everything else, hanging into the tray): the ribbon connectors, the LED switch (Q2, a DPAK soldered on the back, right under J5), the reservoir capacitors, the AA plug, and the power gate (Q5, also a DPAK, with Q6, R14, R15, R16, C7 and C8) behind SELECT's right-hand side.
J1 BATT (4 x AA) ──┬── R12/R13 470k ÷ 2 ── GPIO1 (pack voltage, always readable)
└── Q5 IPD80P03P4L-07 (P-FET) ── VBAT ──┬── C1, C2 470 µF, C3 100 nF
gate: R14 100k to BATT, C8 1 µF to BATT, ├── J5 odd pins ──► LED strings
C7 100 nF to VBAT (soft start);
Q6 2N3904 pulls it to GND via R15 when ARM (GPIO2) is high
LED_RTN ◄── J5 even pins
IR_DRV (GPIO17, 38 kHz) ── R6 47 Ω ── Q2 AOD424 (low side, logic level) ── GNDsim/).| Cable | Ends | Pinout |
|---|---|---|
| 10-way (Adafruit 370, 6") | LED head J1 ↔ control J5 | odd pins LED_PWR, even pins LED_RTN (5 conductors each way) |
| 16-way (Adafruit 2 × 8, 12", cut to ~70 mm) | control J2 ↔ Waveshare header | see below |
tools/check_system.py checks both ribbons pin by pin, and that the firmware's pin numbers
(config.h) match the GPIO each J2 net lands on.
Shorten the 16-way ribbon before fitting it. Both of its ends are in the lid (the display header and J2 are about 50 mm apart along the ribbon's route), and there is no room for 30 cm of ribbon. Cut it so ~70 mm remains between socket centres, and press one of the CNC Tech 3030-16-0102-00 sockets (Digi-Key LKC16H-ND, in the BOM) onto the cut end in a vice, with a scrap of wood each side. Copy the original socket at the other end: the red stripe at the same end and the polarising key on the same face of the ribbon, so it stays straight-through (pin n = pin n). Check with a multimeter that pin 1 goes to pin 1 and pin 16 to pin 16 before plugging it in.
Routing (housing): the two ribbons share the ~3 mm gap between the battery bay's roof and the display's 18650 cell (it hangs below the display board in an open cradle). Lay them side by side, flat: the 10-way on the left half of the roof (towards J5), the 16-way on the right half (towards J2).
| J2 pin | Waveshare | Used for | J2 pin | Waveshare | Used for | |
|---|---|---|---|---|---|---|
| 1 | 3V3 | — (not used) | 2 | VBUS | — (not used) | |
| 3 | GND | GND | 4 | GND | GND | |
| 5 | GPIO0 | SELECT key (also BOOT) | 6 | GPIO19 | — (USB) | |
| 7 | GPIO1 | AA pack ÷ 2 (ADC) | 8 | GPIO20 | — (USB) | |
| 9 | GPIO2 | ARM | 10 | U0TXD (GPIO43) | RIGHT key, through R11 1 k | |
| 11 | GPIO3 | DOWN key | 12 | U0RXD (GPIO44) | LEFT key | |
| 13 | GPIO17 | IR_DRV (RMT, 38 kHz carrier) | 14 | SDA (GPIO13) | — (not used) | |
| 15 | GPIO18 | UP key | 16 | SCL (GPIO14) | BACK key (display board's I2C pull-up) |
The keys use pins the Waveshare board brings out but doesn't need:
Waveshare end of the 16-way ribbon:
firmware/LongRangeRemote/ is the firmware to use. It is a universal remote:
firmware/sd_card/irdb.bin): about 1,640 brands, 6,760
remotes and 233,000 codes from Flipper-IRDB + IRDB. Update them by swapping the file or
uploading it from your phone, without reflashing;.ir files from the SD card;Build it with Partition Scheme "16M Flash (3MB APP/9.9MB FATFS)" and OPI PSRAM, which holds
the codes. Then put irdb.bin on a FAT32 microSD card. See firmware/LongRangeRemote/README.md.
firmware/bringup/bringup.ino is a minimal test of the hardware. It is for Arduino-ESP32 core 3.x
and compiles cleanly for the ESP32-S3 with all warnings on.
| Key | Action |
|---|---|
| Up / Down | Step through the code list |
| Left / Right | Step through the device list |
| SELECT | Sends the selected NEC code (holding it sends NEC repeat frames) and prints the pack voltage, with a warning below 4.6 V |
| BACK | Back to the first code of the first device (and shows GPIO14 reads) |
The Serial prints in printSelection() and handleButtons() mark where your on-screen menu hooks in.
Each transmission follows this sequence:
The code table is placeholder NEC codes. Capture your own devices' codes and replace it.
Never hold IR_DRV high, and don't look into the head at close range.
Prices were checked 3–4 Oct 2026; on 12 Oct the main lines (LEDs, 24R resistors, AOD424, IPD80P03P4L-07, 470 µF, 100 nF, 1 µF, 2N3904, 10-way header, the new IDC socket) were rechecked as in stock at Digi-Key AU. Digi-Key Australia prices are AUD ex GST; Core Electronics prices are AUD inc GST.
| Cost | |
|---|---|
| Digi-Key, everything except the parts below | $75.08 AUD ex GST |
| 33 × ERJ-P08J240V, IPD80P03P4L-07, 2N3904, Keystone 2478 holder | US$6.21, priced from Digi-Key US or Mouser US; the upload file lists them by manufacturer part number |
| JST XHP-2 plug + SXH-001T-P0.6 crimps for the AA holder's leads | in the upload file by part number; prices not checked (you also need an XH crimp tool) |
| Core Electronics (16-way ribbon, header) | $7.15 AUD inc GST |
Not included: the Waveshare ESP32-S3-RLCD-4.2, four AA NiMH cells and a charger, an
unprotected 18650 for the display board (it has its own protection: S8261 + 8205; protected cells are a
few mm longer and may not fit its holder), the PCBs, and the housing hardware (see housing/README.md). The LED head's 2 × 5 header is
two 5-pin pieces of the Core Electronics header strip.
Upload each gerbers/*_jlcpcb.zip with:
-PTH.drl) and non-plated (-NPTH.drl, the four M3 holes) drill files. Smallest features:
0.4 mm via drill, 0.35 mm annular ring, 0.2 mm clearance, silkscreen 1.0 mm text / 0.15 mm lines,
all inside JLCPCB's standard 2-layer process.tools/build_all.sh also runs tools/check_layout.py, which fails the
build on legal-but-poor layout: pads within 1.5 mm of the board edge, a two-pin part more than
12 mm from the rest of its net, and tracks more than 1.5 x (and 8 mm) longer than their pads'
spread. The few deliberate exceptions are listed in the script, each with its reason.sim/).
Q2 and Q5 are DPAKs on the back: solder the tab with a hot iron (or hot air) before the leads.You need:
pcbnew Python module plus kicad-cli.cairosvg and Pillow (for the previews), reportlab and pypdf (for the PDFs).tools/bin/freerouting.jar.cadquery (OpenCascade) and vtk, plus KiCad's 3D models for the parts used.
tools/render_3d.py --fetch MODELS_DIR downloads just those from KiCad's packages3D repository.tools/build_all.sh # rebuild everything, re-using the saved control-board route (*.ses)
tools/build_all.sh --reroute # also re-run the autorouter (after moving parts)
tools/render_3d.py MODELS_DIR # 3D renders of both boards into previews/The generators rebuild each board from scratch. Once you start editing in KiCad, treat the KiCad files as the source of truth.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | M3 | MountingHole:MountingHole_3.2mm_M3 | H1, H2, H3, H4 |
| 3 | 100k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R4, R7, R14 |
| 3 | 100nF 50V | Capacitor_THT:C_Rect_L4.0mm_W2.5mm_P2.50mm | C3, C6, C7 |
| 2 | 10k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R15, R16 |
| 2 | 470k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R12, R13 |
| 2 | 470uF 25V | Capacitor_THT:CP_Radial_D10.0mm_P5.00mm | C1, C2 |
| 1 | 1k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R11 |
| 1 | 1uF 50V | Capacitor_THT:C_Disc_D5.1mm_W3.2mm_P5.00mm | C8 |
| 1 | 2N3904 | Package_TO_SOT_THT:TO-92_Inline_Wide | Q6 |
| 1 | 47R | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R6 |
| 1 | 4xAA (JST-XH) | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J1 |
| 1 | AOD424 | Package_TO_SOT_SMD:TO-252-2 | Q2 |
| 1 | BACK | Button_Switch_THT:SW_PUSH_6mm | SW6 |
| 1 | DOWN | Button_Switch_THT:SW_PUSH_6mm | SW2 |
| 1 | IPD80P03P4L-07 | Package_TO_SOT_SMD:TO-252-2 | Q5 |
| 1 | LEFT | Button_Switch_THT:SW_PUSH_6mm | SW3 |
| 1 | RIGHT | Button_Switch_THT:SW_PUSH_6mm | SW4 |
| 1 | SELECT | Button_Switch_THT:SW_PUSH_6mm | SW5 |
| 1 | TO LED HEAD | Connector_IDC:IDC-Header_2x05_P2.54mm_Vertical | J5 |
| 1 | TO WAVESHARE | Connector_IDC:IDC-Header_2x08_P2.54mm_Vertical | J2 |
| 1 | UP | Button_Switch_THT:SW_PUSH_6mm | SW1 |

LukeRJamieson/long-range-remote
A hand-held universal IR remote with far more range than a normal one. A head of 66 narrow-beam (±5°) SFH 4545 emitters sits at the front of a 107 × 52 × 170 mm block. Behind it are:



joeycastillo/Sensor-Watch
A board replacement for the classic Casio F-91W wristwatch

hoglet67/RGBtoHDMI
Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

openwch/ch32v003
CH32V003 is an ultra-cheap RISC-V MCU with 2KB SRAM, 16KB flash, and up to 18 GPIOs that sells for under $0.10

Luos-io/luos_engine
Open-source and real-time orchestrator for cyber-physical-systems, to easily design, test and deploy embedded applications and digital twins.
BlueAndi/Pixelix
Full RGB LED matrix, based on an ESP32 and WS2812B LEDs or emulated LEDs on TFT.
It measures 82 × 52 mm and has 2 copper layers, 1.6 mm thick.
31 parts, built around the AOD424 and IPD80P03P4L-07. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the LukeRJamieson/long-range-remote repository on GitHub, at the commit this page was made from: the board is control_lite/control_lite.kicad_pcb and its schematic control_lite/control_lite.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask LukeRJamieson before reusing the design.