Skip to the content
2 layers33 × 47.6 mmEDID spoofer, the printed circuit board in 3D

Simple board that can act as dummy plug or can override EDID of a display, or access VESA DDC interface externally.

Size
33 × 47.6 mm
Copper layers
2
Thickness
1.6 mm
Parts
13
Nets
21
Pads
65
Tracks, vias
108, 58
Pours
2
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
18 Jun 2024
Updated
21 Jun 2024

Overview

EDID spoofer is an open-source printed circuit board by Leo-PL, from the Leo-PL/EDID-spoofer repository on GitHub, published under the Unlicense licence. It is a 2-layer board of 33 × 47.6 mm with 13 parts on 21 nets, routed with 108 tracks and 58 vias.

It is built around the 24LCS22A-I/P. Its parts include 3 resistors, 3 connectors, 1 capacitor and 1 IC. It belongs with the lEDs and displays boards of this library.

Main components

1

README

README.md

EDID Spoofer

A simple board, that helps tinkering with VESA DDC

  • Override EDID on a display for custom resolutions
  • Provide a EDID to the PC for sinks which lack EDID, like with BNC inputs
  • Act as a dummy plug for servers for Intel AMT
  • Sniff or interfere with DDC communication between the graphics card and the display

Parts used:

  • 1x DE-15HD THT plug (towards graphics card).
  • 1x DE-15HD THT receptacle (towards display).
  • 24LCS22A, 24LC21A, or compatible VESA DDC1/DDC2 EEPROM. A generic 24C02 should work too.
  • 1 3x 10k 0805 SMD resistors.
  • 1x 100nF 0805 SMD capacitor.
  • Generic 4-pin header for programming or external bus access.

Programming

First programming can be done even if write protection is enabled, which is set by default using JP1 jumper. Chip locks itself when address 0x7F (the EDID checksum) is written. For programming, you can use SNANDer, i2c-tools or any other tool compatible with I²C EEPROMs. If using ordinary 24C02, be sure to keep WP pin low, as this is A2 pin on that part, otherwise chip address won't match. DDC1 and write protection also won't work in this case.

Redistribution

Project contents are freely redistributable in any form. Please see the license.

Parts

13
QtyValueFootprintReferences
310kResistor_SMD:R_0805_2012MetricR1, R2, R3
2SolderJumper_2_BridgedJumper:SolderJumper-2_P1.3mm_Bridged_RoundedPad1.0x1.5mmJP2, JP3
2SolderJumper_2_OpenJumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mmJP4, JP5
1100nCapacitor_SMD:C_0805_2012MetricC1
124LCS22APackage_SO:SO-8_3.9x4.9mm_P1.27mmU1
1Conn_01x04Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ3
1DE15_Plug_HighDensity_MountingHolesConnector_Dsub:DSUB-15-HD_Male_Horizontal_P2.29x1.98mm_EdgePinOffset8.35mm_Housed_MountingHolesOffset10.89mmJ1
1DE15_Receptacle_HighDensity_MountingHolesConnector_Dsub:DSUB-15-HD_Female_Horizontal_P2.29x1.98mm_EdgePinOffset8.35mm_Housed_MountingHolesOffset10.89mmJ2
1SolderJumper_3_Bridged12Jumper:SolderJumper-3_P1.3mm_Bridged12_RoundedPad1.0x1.5mm_NumberLabelsJP1

Similar boards

  • 2 layers40 × 20 mmUsb uart, the printed circuit board in 3D

    Usb uart

    earthtojake/text-to-cad

    Design physical products with AI

    13 parts26kMIT
  • 2 layers35 × 29 mmMagSpoofTC, the printed circuit board in 3D

    MagSpoofTC

    samyk/magspoof

    A portable device that can spoof/emulate any magnetic stripe, credit card or hotel card "wirelessly", even on standard magstripe (non-NFC/RFID) readers.

    13 parts4.2k
  • 2 layers20.6 × 23.6 mmAO-03 signal amplifier, the printed circuit board in 3D

    AO-03 signal amplifier

    fossasia/pslab-scripts

    Pocket Science Lab - Scripts for Sensor Experiments

    13 parts1.6kApache-2.0
  • 2 layers47 × 35.6 mmMX7-C-35PL C11, the printed circuit board in 3D

    MX7-C-35PL C11

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    13 parts1.2k
  • 2 layers95 × 95 mmCube batteryboard, the printed circuit board in 3D

    Cube batteryboard

    willem-pennings/balancing-cube

    A cube that balances itself in a corner or edge using reaction wheels

    13 parts1.1kGPL-3.0
  • 2 layers15.2 × 20.3 mmPt100stick, the printed circuit board in 3D

    Pt100stick

    VoronDesign/Voron-Hardware

    Cool Hardware designed by the Voron Design group

    13 parts1.1kGPL-3.0
  • 2 layers53.9 × 23.2 mmBuffer, the printed circuit board in 3D

    Buffer

    hoglet67/RGBtoHDMI

    Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

    13 parts1kGPL-3.0

Questions

How big is the EDID spoofer PCB?

It measures 33 × 47.6 mm and has 2 copper layers, 1.6 mm thick.

What parts does the EDID spoofer use?

13 parts, built around the 24LCS22A-I/P. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the EDID spoofer KiCad files?

From the Leo-PL/EDID-spoofer repository on GitHub, at the commit this page was made from: the board is EDID_spoofer.kicad_pcb and its schematic EDID_spoofer.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the EDID spoofer design in my own project?

Its repository publishes it under the Unlicense licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).