Skip to the content
2 layers50 × 20 mmST Connector, the printed circuit board in 3D

ST Connector

Lenka-12/EEE4022S

A high-performance audio digitization system built around the STM32F7 microcontroller, featuring dual Delta-Sigma ADCs (PCM1808 and ADAU1978) and an integrated ADC for comprehensive audio capture.

Size
50 × 20 mm
Copper layers
2
Thickness
1.6 mm
Parts
5
Nets
15
Pads
32
Tracks, vias
35, 4
Pours
1
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
24 Oct 2024
Updated
30 Oct 2024

Overview

ST Connector is an open-source printed circuit board by Lenka-12, from the Lenka-12/EEE4022S repository on GitHub. It is a 2-layer board of 50 × 20 mm with 5 parts on 15 nets, routed with 35 tracks and 4 vias.

It is built around the M55-6001242R. Its parts include 3 connectors and 2 resistors.

Main components

1

README

README.md

Audio Digitisation System 🎵

License: MIT

A high-performance audio digitization system built around the STM32F7 microcontroller, featuring dual Delta-Sigma ADCs (PCM1808 and ADAU1978) and an integrated ADC for comprehensive audio capture.

🎯 Overview

This project implements a complete audio digitization pipeline that captures audio data through multiple ADCs and transmits it to a PC for MATLAB-based analysis.

🔧 Hardware Components

STM32F7 Nucleo Board

  • Main processing unit
  • Handles ADC interfacing and USB communication

PCM1808 Delta-Sigma ADC (Buy)

  • Stereo Audio ADC configuration
  • Input: Bottom port MEMS microphone from DEVKIT-MEMS-001
  • Signal conditioning via AD828 op-amp module (AD828 Module Source)
  • I2S interface via SAI1 Block B
  • 48 kHz sampling rate
  • DMA circular mode operation

Integrated ADC

  • Input: Nucleo board pin A3
  • Signal from top port MEMS microphone (DEVKIT-MEMS-001)
  • Signal conditioning via BOB-09816 (SparkFun BOB-09816)
  • Timer-triggered operation
  • Circular DMA mode

ADAU1978 Delta-Sigma ADC

  • Integrated via STEVAL-STWINMAV1 module
  • TDM4 protocol through SAI1 Block A
  • 24-bit resolution at 48 kHz
  • DMA circular mode operation

Important Note: When configuring SAI for TDM:

  • Clock strobing must be set to rising edge
  • Frame Synchro offset must be set before the First Bit

🔌 Communication

USB Interface

  • Protocol: USB Full Speed (FS) CDC
  • Data transmission triggered by user button
  • ADC activation controlled via Python script commands

💡 Status Indicators

LEDFunction
LD1Integrated ADC active
LD2PCM1808 active
LD3ADAU1978 active

🛠️ Hardware Sources

Microphones

  • DEVKIT-MEMS-001
    • Bottom port MEMS mic → PCM1808
    • Top port MEMS mic → Integrated ADC

Signal Conditioning

ADC Modules

📝 PCB Documentation

The repository includes:

  • STEVAL-STWINMAV1 module adapter designs
  • Audio Digitisation Hardware based on PCM1862 (production pending)

📊 Data Analysis

MATLAB scripts are provided for processing the captured audio data. See the /Processing directory for analysis tools.

🤝 Contributing

Contributions are welcome! Please read our Contributing Guide for details on our code of conduct and the process for submitting pull requests.

📄 License

This project is licensed under the MIT License - see the LICENSE file for details.

✨ Acknowledgments

  • STMicroelectronics for the STEVAL-STWINMAV1 reference design
  • Same Sky for DEVKIT-MEMS-001
  • SparkFun Electronics for BOB-09816
  • Contributors and testers

For technical questions and support, please open an issue in the repository.

Parts

5
QtyValueFootprintReferences
24.7kResistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_HorizontalR1, R2
1Conn_01x04_PinConnector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ2
1Conn_01x06_PinConnector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_VerticalJ3
1M55-6001242RKiCad:M556001242RJ1

More from Lenka-12/EEE4022S

1
  • 2 layers100 × 100 mmAudio Digitizer, the printed circuit board in 3D

    Audio Digitizer

    Lenka-12/EEE4022S

    A high-performance audio digitization system built around the STM32F7 microcontroller, featuring dual Delta-Sigma ADCs (PCM1808 and ADAU1978) and an integrated ADC for comprehensive audio capture.

    121 parts

Similar boards

  • 4 layers99.8 × 94.6 mmOresat1-plusz end card, the printed circuit board in 3D

    Oresat1-plusz end card

    oresat/oresat-end-cards

    Repo for the OreSat +/-Z end cards (Card #1 and #20)

    109 parts2
  • 2 layers98 × 27 mmXy limit, the printed circuit board in 3D

    Xy limit

    opulo-inc/lumenpnp

    The LumenPnP is an open source pick and place machine.

    5 parts3.7k
  • 2 layers21 × 33 mm24g2usb pico2w, the printed circuit board in 3D

    24g2usb pico2w

    joypad-ai/joypad-os

    Universal controller firmware for building adapters, dongles, and custom controllers.

    5 parts1.7kApache-2.0
  • 2 layers53.2 × 59.6 mmA10 OLinuXino Lime Rev B SHIELD TEMPLATE, the printed circuit board in 3D

    A10 OLinuXino Lime Rev B SHIELD TEMPLATE

    OLIMEX/OLINUXINO

    OLINUXINO is Open Source / Open Hardware, low cost from EUR 24 Linux Industrial grade Single Board Computer capable to operate -25+85C

    5 parts1.5k
  • 2 layers30 × 11 mmMain control board servo tester, the printed circuit board in 3D

    Main control board servo tester

    jamro/tiny-engineer

    A small desktop robot that brings an AI coding assistant to life, physically acting out when it reads files, thinks, writes code, and finishes work.

    5 parts1.1k
  • 2 layers78.8 × 35.3 mmKiCadTest, the printed circuit board in 3D

    KiCadTest

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    5 parts915
  • 2 layers50 × 23 mmMiniCircuits LTCC, the printed circuit board in 3D

    MiniCircuits LTCC

    VanceVagell/kv4p-ht

    Open source handheld ham radio project KV4P-HT

    5 parts828GPL-3.0

Questions

How big is the ST Connector PCB?

It measures 50 × 20 mm and has 2 copper layers, 1.6 mm thick.

What parts does the ST Connector use?

5 parts, built around the M55-6001242R. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the ST Connector KiCad files?

From the Lenka-12/EEE4022S repository on GitHub, at the commit this page was made from: the board is PCB/ST_Connector/PCB/PCB.kicad_pcb and its schematic PCB/Audio_Digitizer/ADC.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the ST Connector design in my own project?

Its repository states no licence, so its author keeps all rights: ask Lenka-12 before reusing the design.