2 layers70.5 × 49 mm
2 layers116.8 × 119.4 mm
TeensyBreakout
leighmurray/TeensyBreakout- Size
- 116.8 × 119.4 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 112
- Nets
- 152
- Pads
- 493
- Tracks, vias
- 1,400, 364
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 6 Dec 2021
- Updated
- 6 Jan 2022
Overview
TeensyBreakout is an open-source printed circuit board by leighmurray, from the leighmurray/TeensyBreakout repository on GitHub. It is a 2-layer board of 116.8 × 119.4 mm with 112 parts on 152 nets, routed with 1,400 tracks and 364 vias.
It is built around the TEENSY 4.1, SGTL5000XNAA3 and TDA7265, with the ZLDO1117G33TA, BSD223P and EG1218 among its other parts. Its parts include 29 capacitors, 24 resistors, 8 connectors, 5 ICs and 4 diodes. It belongs with the NXP (LPC, Kinetis, i.MX RT) boards of this library.
Main components
12
TEENSY 4.1
Development Boards & Kits - ARM ModuleSparkFun ElectronicsUncategorised
SGTL5000XNAA3
QFN-32-EP(5x5)-40℃~+85℃ 1.62V~3.6V 8kHz~96kHz Built-in phase-locked loop、On-chip digital gain、Mute control Encoder/decoder I2S、I2C、SPI QFN-32-EP(5x5) Audio Interface ICs ROHSNXP SemiconductorsAudio Interface ICs
TDA7265
Multiwatt-11-V-20℃~+85℃ 0.01% 2-Channel 25Wx2@8Ω 5V~25V 60dB 80mA Automatic mute/no-noise switch、Enable/shutdown function、Automatic power-saving mode Class AB Multiwatt-11-V Audio Amplifiers ROHSSTMicroelectronicsAudio Amplifiers
ZLDO1117G33TA
SOT-223-4-40℃~+125℃@(Tj) 1 1.35V@(1A) 10mA 18V 1A 3.3V 80dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223-4 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSDiodes IncorporatedVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
BSD223P
SOT-363-55℃~+150℃ 150mW 15pF 160pF 2 P-Channel 20V 20pF 4.1nC@4.5V 430mΩ@4.5V、624mΩ@2.5V、950mΩ@1.8V 660mA SOT-363 MOSFETs ROHSTECH PUBLICMOSFETs
EG1218
插件-20℃~+70℃ 11.6mm 200mA 30V 4mm 7.4mm Black PC Pin Rectangular Columnar SPDT Through Hole Plugin Slide Switches ROHSE-SwitchSlide Switches
1N5231BTR
DO-35-65℃~+200℃ 1 Independent 1.6kΩ 17Ω 4.845V~5.355V 5.1V 500mW 5uA@2V DO-35 Zener Diodes ROHSonsemiZener Diodes
73725-0110BLF
插件-55℃~+85℃ 1 2.5A 4P Female Right Angle Type-A USB 2.0 White 插件 USB Connectors ROHSAmphenolUSB Connectors
B5818LWS-TP
SOD-323-65℃~+125℃ 1 Independent 10A 1A 200uA@30V 30V 450mV@1A SOD-323 Schottky Diodes ROHSMicro Commercial ComponentsSchottky Diodes
CMA-4544PF-W
--44dB@±2dB 2.2kΩ 3V~10V 4.65mm 500uA 60dB 9.7mm Omnidirectional 插件,D=9.7mm Microphones ROHSCUIBuzzers
CR1220-2
--40~80℃ Battery base CR1220 Phosphor bronze - Battery holder base ROHSQ&JButton And Strip Battery Connector
FDN340P
SOT-23-55℃~+150℃ 1 P-Channel 1.5V 121pF 20V 2A 500mW 56pF 7.2nC@4.5V 70mΩ@4.5V 779pF P-Channel SOT-23 MOSFETs ROHSonsemiMOSFETs
Parts
112| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | R_Small | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R23, R24, R25, R26, R27, R28, R29, R30, R31, R32 |
| 6 | 2.2uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C26, C28, C31, C32, C35, C36 |
| 5 | 0.1uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C27, C29, C30, C33, C34 |
| 5 | 10K | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R2, RN5A1, RN5B1, RN8A1, RN8B1 |
| 5 | CP_Small | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C37, C38, C39, C41, C42 |
| 4 | 10uf | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2, C3, C4, C5 |
| 4 | 1K | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R4, RN1A1, RN1B1 |
| 4 | C_Small | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C40, C43, C44, C45 |
| 3 | 2.2K | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R19, R21, R22 |
| 3 | Conn_01x08 | Connector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_Vertical | JP9, JP10, JP11 |
| 3 | SolderJumper_2_Open | Jumper:SolderJumper-2_P1.3mm_Open_TrianglePad1.0x1.5mm | SJ1, SJ4, SJ5 |
| 2 | 22k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | RN2A1, RN2B1 |
| 2 | Amber | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | RXD1, TXD1 |
| 2 | BSD223P | Package_TO_SOT_SMD:SOT-23 | Q1A1, Q1B1 |
| 2 | Conn_01x08_Female | Connector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_Vertical | JP5, JP6 |
| 2 | EG1218 | digikey-footprints:Switch_Slide_JS202011SCQN | S1, S2 |
| 2 | ESP-PRG | Button_Switch_THT:SW_PUSH_6mm | PRG-DTSM1, RST-DTSM6 |
| 2 | Jumper_NO_Small | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | SJ2, SJ3 |
| 2 | Red | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D13, PWR1 |
| 2 | SolderJumper_2_Bridged | Jumper:SolderJumper-2_P1.3mm_Bridged_Pad1.0x1.5mm | JP12, JP13 |
| 1 | 0.15uf | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C25 |
| 1 | 100 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R20 |
| 1 | 100nf | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C9 |
| 1 | 10uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C6 |
| 1 | 1A-Hold | Fuse:Fuse_0603_1608Metric_Pad1.05x0.95mm_HandSolder | F1 |
| 1 | 1N5231BTR | digikey-footprints:DO-35 | Z1 |
| 1 | 22uf | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C7 |
| 1 | 2491 | digikey-footprints:WIFI_Module_ESP8266_2491 | MOD1 |
| 1 | 25K | Potentiometer_THT:Potentiometer_TT_P0915N | RV2 |
| 1 | 330 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R3 |
| 1 | 47uf | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C1 |
| 1 | 600 | digikey-footprints:0805 | FB3 |
| 1 | 73725-0110BLF | digikey-footprints:USB_A_Female_Vertical_RA_73725-0110BLF | J1 |
| 1 | AP7313 | Package_TO_SOT_SMD:SOT-23_Handsoldering | LDO1 |
| 1 | Arduino_Due_Shield | CustomFootprints:Arduino_Due_Shield | XA** |
| 1 | B5818LWS-TP | digikey-footprints:SOD-323 | D1 |
| 1 | BC107 | Package_TO_SOT_THT:TO-18-3 | Q6 |
| 1 | CMA-4544PF-W | digikey-footprints:Mic_CMA-4544PF-W | MIC1 |
| 1 | CR1220 | Battery:BatteryHolder_Keystone_3000_1x12mm | BT1 |
| 1 | Conn_01x04 | Connector_JST:JST_PH_S4B-PH-K_1x04_P2.00mm_Horizontal | J2 |
| 1 | Conn_01x10_Female | Connector_PinSocket_2.54mm:PinSocket_1x10_P2.54mm_Vertical | JP1 |
| 1 | Conn_02x03_Odd_Even | CustomFootprints:PinSocket_2x03_P2.54mm_Vertical(Flipped) | SPI1 |
| 1 | Conn_02x18_Odd_Even | Connector_PinSocket_2.54mm:PinSocket_2x18_P2.54mm_VerticalFlipped | JP8 |
| 1 | FDN340P | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | Headphone | digikey-footprints:Switch_Slide_11.6x4mm_SJ-3523-SMT | CON2 |
| 1 | LHS-02-TRA | Connector_JST:JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | VIN1 |
| 1 | Line In | digikey-footprints:Switch_Slide_11.6x4mm_SJ-3523-SMT | CON3 |
| 1 | MH2029-300Y | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | L1 |
| 1 | NCP1117ST50T3G | digikey-footprints:SOT-223 | IC2 |
| 1 | OSTTC022162 (L) | digikey-footprints:Term_Block_1x2_P5.08MM | J6 |
| 1 | OSTTC022162 (R) | digikey-footprints:Term_Block_1x2_P5.08MM | J5 |
| 1 | PJ-102A | digikey-footprints:Barrel_Jack_5.5mmODx2.1mmID_PJ-102A | J4 |
| 1 | RJ45_LED | Connector_RJ:RJ45_Amphenol_RJHSE538X | J3 |
| 1 | SGTL5000XNAA3 | Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.6x3.6mm | U5 |
| 1 | SW_MEC_5E | Button_Switch_THT:SW_PUSH_6mm | SW1 |
| 1 | SolderJumper_3_Bridged12 | Jumper:SolderJumper-3_P1.3mm_Bridged12_RoundedPad1.0x1.5mm_NumberLabels | JP22 |
| 1 | TDA7265 | Package_TO_SOT_THT:TO-220-11_P3.4x5.08mm_StaggerOdd_Lead4.85mm_Vertical | U6 |
| 1 | Teensy4.1 | teensy:Teensy41 | U1 |
| 1 | Yellow | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | LED10 |
| 1 | ZLDO1117G33 | digikey-footprints:SOT-223 | IC1 |
The 110 most common of 112 parts.
Similar boards
- 4 layers18.5 × 40.4 mm
- 2 layers264 × 34 mm
- 2 layers88.9 × 88.9 mm
Knob v1
bmo/tuning-knob-pcboard
KiCAD PC Board design for a tuning knob that works with Flex Radio SmartSDR, PowerSDR, and RHR. Uses STM32 hardware.
25 parts7MIT - 2 layers100 × 100 mm
JBT01
jbteja/tj01-ms51-heater-controller
A heater control system featuring deterministic operation, safety auto-cutoff, predefined timer modes, and temperature measurement using a K-type thermocouple.
79 parts1 - 2 layers45 × 45 mm
- 6 layers104 × 91.5 mm
Electronic Board V2.0
lucacros/GuitarePedal_2324Project
Projet de 2ème année à l'ENSEA, création d'une pédale de guitare. CROSETTO Luca / THOMASSET Jolan / LANFREDI Camille
109 parts - 2 layers100 × 100 mm
Questions
How big is the TeensyBreakout PCB?
It measures 116.8 × 119.4 mm and has 2 copper layers, 1.6 mm thick.
What parts does the TeensyBreakout use?
112 parts, built around the TEENSY 4.1, SGTL5000XNAA3, TDA7265 and ZLDO1117G33TA. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the TeensyBreakout KiCad files?
From the leighmurray/TeensyBreakout repository on GitHub, at the commit this page was made from: the board is TeensyBreakout.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the TeensyBreakout design in my own project?
Its repository states no licence, so its author keeps all rights: ask leighmurray before reusing the design.