2 layers344.7 × 123.6 mm
2 layers270 × 100 mm
XplodePCB
LeeZard79/XplodePCB- Size
- 270 × 100 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 194
- Nets
- 161
- Pads
- 946
- Tracks, vias
- 2,197, 274
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 12 Dec 2024
- Updated
- 20 Feb 2025
Overview
XplodePCB is an open-source printed circuit board by LeeZard79, from the LeeZard79/XplodePCB repository on GitHub. It is a 2-layer board of 270 × 100 mm with 194 parts on 161 nets, routed with 2,197 tracks and 274 vias.
It is built around the RP2040, 74AHCT1G125SE and W25Q128JVSIQ, with the SRV05-4 among its other parts. Its parts include 101 diodes, 17 capacitors, 9 resistors, 5 ICs and 4 switches. It belongs with the RP2040 boards of this library.
Main components
4
RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)
74AHCT1G125SE
SOT-353-40℃~+125℃ 1 1 4.5V~5.5V 4.7ns@5V,50pF 40uA 74AHCT 8mA 8mA Schmitt trigger Tri-State Unidirectional SOT-353 Buffers, Drivers, Receivers, Transceivers ROHSDiodes IncorporatedBuffers, Drivers, Receivers, Transceivers
W25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASH
SRV05-4
SOT-23-6L-55℃~+150℃ 15V 1pF 4A 5V 5uA 6V 80W ESD Four channels IEC 61000-4-2、IEC 61000-4-5 Unidirectional SOT-23-6L ESD and Surge Protection (TVS/ESD) ROHShongjiachengESD And Surge Protection (TVS/ESD)
Parts
194| Qty | Value | Footprint | References |
|---|---|---|---|
| 51 | D_Small | Diode_SMD:D_SOD-123 | D1, D2, D10, D11, D12, D13, D14, D15, D16, D17, D18, D19, D20, D21, D22, D23 +35 |
| 50 | MX_SK6812MINI-E | PCM_marbastlib-mx:LED_MX_6028R | LED1, LED2, LED10, LED11, LED12, LED13, LED14, LED15, LED16, LED17, LED18, LED19, LED20, LED21, LED22, LED23 +34 |
| 49 | MX_SW_HS | PCM_marbastlib-mx:SW_MX_HS_CPG151101S11_1u | MX1, MX2, MX10, MX11, MX12, MX13, MX14, MX15, MX16, MX17, MX18, MX19, MX20, MX21, MX22, MX23 +33 |
| 8 | 100n | Capacitor_SMD:C_0402_1005Metric | C4, C7, C8, C9, C13, C14, C15, C16 |
| 5 | 1u | Capacitor_SMD:C_0402_1005Metric | C1, C2, C3, C6, C10 |
| 5 | 5.1k | Resistor_SMD:R_0402_1005Metric | R1, R2, R3, R4, R5 |
| 2 | 1k | Resistor_SMD:R_0402_1005Metric | R6, R9 |
| 2 | 22p | Capacitor_SMD:C_0402_1005Metric | C11, C12 |
| 2 | 27 | Resistor_SMD:R_0402_1005Metric | R7, R8 |
| 2 | LOGO | LOGO | G***, G*** |
| 2 | MX_stab | PCM_marbastlib-mx:STAB_MX_P_3u | S3, S4 |
| 2 | SW_Push | Button_Switch_SMD:SW_SPST_TL3342 | BOOT1, RST1 |
| 1 | 100nF | Capacitor_SMD:C_0402_1005Metric | C17 |
| 1 | 10u | Capacitor_SMD:C_0603_1608Metric | C5 |
| 1 | 74AHCT1G125 | Package_TO_SOT_SMD:SOT-23-5 | U5 |
| 1 | Crystal_GND24 | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | Fuse_Small | Fuse:Fuse_1206_3216Metric | F1 |
| 1 | MX_SW_HS | Rotary_Encoder:RotaryEncoder_Alps_EC11E-Switch_Vertical_H20mm | MX6 |
| 1 | MX_SW_HS | PCM_marbastlib-mx:SW_MX_HS_CPG151101S11_1.25u | MX7 |
| 1 | MX_stab | PCM_marbastlib-mx:STAB_MX_P_ISO | S1 |
| 1 | MX_stab | PCM_marbastlib-mx:STAB_MX_P_2u | S2 |
| 1 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U3 |
| 1 | SRV05-4 | Package_TO_SOT_SMD:SOT-23-6 | U2 |
| 1 | USB_C_Receptacle_USB2.0_16P | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.23x5.23mm_P1.27mm | U4 |
| 1 | XC6206PxxxMR | Package_TO_SOT_SMD:SOT-23-3 | U1 |
Similar boards
- 2 layers158.8 × 100.2 mm
- 2 layers92.3 × 115.4 mm
Macropad
wwintjong/macropad
My take on a macropad that I think will suit me. The layout is a 5x4 keys with hot-swappable switch and LED. Current iteration has no knobs or display implemented, but that is an idea for future versions.
120 parts - 2 layers149 × 224 mm
GDEK
GilDev/GDEK
Low-profile, compact, beginner-friendly, assembly-friendly 4×6 with 5-keys thumb cluster ergonomic keyboard with universal keyswitch support, per-key RGB LED, encoder and RP2040 controller. Phew, that’s a lot!
324 parts3CERN-OHL-S-2.0 - 4 layers51.8 × 68.3 mm
- 2 layers248.6 × 81.9 mm
Alpha curISO
calvin-mcd/alpha-curISO
The Alpha CurISO is a community pcb for the Curio. It supports two different Alpha Staggers and Ortho Layouts. This is a collaboration between jadethemaid, airuei, galvy0 and calvin.
241 parts2 - 2 layers79.2 × 106.7 mm
MacroPad
landodoughty/MacroPad
A Custom Macro Pad I Designed and Built based on the RP2040
111 parts2MIT - 2 layers83 × 127 mm
Numpad
blafr103/pico-numpad
Hand-wired 17-key USB numpad on Pi Pico W. CircuitPython, diode matrix, event-driven scanning.
120 partsMIT
Questions
How big is the XplodePCB PCB?
It measures 270 × 100 mm and has 2 copper layers, 1.6 mm thick.
What parts does the XplodePCB use?
194 parts, built around the RP2040, 74AHCT1G125SE, W25Q128JVSIQ and SRV05-4. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the XplodePCB KiCad files?
From the LeeZard79/XplodePCB repository on GitHub, at the commit this page was made from: the board is Rev2PCB.kicad_pcb and its schematic Rev2PCB.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the XplodePCB design in my own project?
Its repository states no licence, so its author keeps all rights: ask LeeZard79 before reusing the design.