
Jbc station
hrandib/jbc_station
3 channel universal soldering station for T12, T115, T210, T245, T470 handles

Embedded MOSFET with Active Brake and cross-conduction protection for Airsoft electric guns (AEG).
Active Brake DC motor is an open-source printed circuit board by lazarev-lab, from the lazarev-lab/AEG_Active_Brake repository on GitHub, published under the MIT licence. It is a 2-layer board of 30 × 13 mm with 21 parts on 11 nets, routed with 162 tracks and 14 vias.
It is built around the LM5106MM, GT007N04TL and BAT54, with the SMBJ18A among its other parts. Its parts include 6 resistors, 3 capacitors, 3 diodes, 2 transistors and 1 IC. It belongs with the robots and motor control boards of this library.
A compact high-performance MOSFET module for Airsoft Electric Guns (AEGs).
The design replaces traditional mechanical trigger contacts with an electronic switching system based on a half-bridge MOSFET driver, improving trigger response, reducing contact wear, and providing active motor braking to minimize overspin.
Mechanical trigger contacts carry only a low-current control signal while all motor current flows through dedicated power MOSFETs.
Benefits:
Upon trigger release, the half-bridge actively drives the motor terminals toward the supply rail, rapidly dissipating the motor's rotational energy.
This significantly reduces gearbox overspin and helps prevent unintended double-shots, especially in high-speed builds.
The design uses the LM5106MM half-bridge gate driver with a fixed 600 ns dead time.
This hardware-enforced delay guarantees that the high-side and low-side MOSFETs cannot switch simultaneously.
Benefits:
The circuit includes dedicated protection against voltage spikes generated by the motor.
| Component | Function |
|---|---|
SMBJ18A | Clamps supply voltage transients during switching and braking |
SS34 | Provides an additional low-loss current path and suppresses inductive transients |
The trigger input uses an active-low configuration with a pull-up resistor.
This helps prevent accidental firing caused by:
The trigger controls the HB input of the LM5106MM.
HB = LOWHB = HIGHThe gate driver automatically inserts a fixed 600 ns dead time during every switching transition.
| Parameter | Value |
|---|---|
| Operating Voltage | 7.4 V – 14.8 V Li-Po (2S–4S) |
| Gate Driver | LM5106MM |
| Dead Time | 600 ns |
| Power MOSFETs | 2 × GT007N04TL |
| TVS Diode | SMBJ18A |
| Schottky Diode | SS34 |
| Trigger Type | Dry Contact / Microswitch |
| Active Brake | Yes |
| Pad | Connection |
|---|---|
| +Bat | Battery Positive (+) |
| -Bat | Battery Negative (-) |
| +Motor | Motor Positive (+) |
| -Motor | Motor Negative (-) |
| Buton | Trigger Contact |
| Buton_2 | Trigger Contact (GND) |
The trigger simply shorts Buton to Buton_2 when pressed.
This design does not include reverse-polarity protection.
Connecting the battery backwards may permanently damage:
Always verify wiring before connecting a battery.
.
├── *.kicad_pro # KiCad project
├── *.kicad_sch # Schematic
├── *.kicad_pcb # PCB layout
└── .gitignore # KiCad-specific ignore rulesReleased under the MIT License.
You are free to use, modify, manufacture, and distribute this design, including commercial use, provided that the original copyright notice and license text are retained.
See the LICENSE file for details.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 3S_PADS_1WAY_1MM | Vault:PADS_1WAY_1MM | -B, -M, +B, +M, S, S1 |
| 2 | 10 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R5, R6 |
| 2 | 100K | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R2, R4 |
| 2 | 100nF | Vault:FP-CGA3E-0_3-0_1-IPC_C | C2, C3 |
| 2 | GT007N04TL | Vault:FP-100CU-MFG | Q1, Q2 |
| 1 | 100K | Vault:0402_RESC1005N | R3 |
| 1 | 1uF | Vault:FP-CGA3E-0_3-0_1-IPC_C | C1 |
| 1 | 2K | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R7 |
| 1 | BAT54 | Vault:FP-SOD-523-MFG | D1 |
| 1 | LM5106MM | Package_SO:VSSOP-10_3x3mm_P0.5mm | U1 |
| 1 | SMBJ18A | Diode_SMD:D_SMA | D3 |
| 1 | SS34 DO-214AC | Vault:FP-SMA-MFG | D2 |

hrandib/jbc_station
3 channel universal soldering station for T12, T115, T210, T245, T470 handles

FPV-Drone-STM32F411/DroneController
All-in-one FPV drone PCB with integrated flight controller, PDB, and ESCs built around STM32F411.

OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.

nuerolynx/embedded-systems-lab
Arduino UNO R4 WiFi and ESP32 prototypes for access control, automation, displays, monitoring, and Bluetooth audio.

AssaadMH/shadow-4wd-motor-shield-pcb
The 24-signal interface board that replaces SHADOW's perfboard wiring — and the two pin conflicts that only appeared on re-checking the spec.

dhruxraj/stm32-can-ecu
A compact, "ECU-style" CAN node for learning and prototyping automotive-type embedded software. It has an STM32G4 MCU, a CAN transceiver with protection and switchable termination, a 6-axis IMU, a protected 8-18 V…

quangvd917/ab125-kline
Bản mới của kline-l9637d: C3 SuperMini cắm thẳng lên mạch qua rào cái, không còn giắc J2. PCB một mặt, kích thước 70 × 38 mm, để tự làm. Firmware dùng env c3supermini như cũ, không phải sửa.

renatorgr/Boards
Hardware and firmware for the AgOpenGPS AiO v4.5 autosteer boards: Teensy 4.1 firmware with its own web page (GPS, IMU, autosteer), a XIAO ESP32 Wi-Fi status page, XIAO adapter boards, and an Arduino Nano sprayer…
It measures 30 × 13 mm and has 2 copper layers, 1.6 mm thick.
21 parts, built around the LM5106MM, GT007N04TL, BAT54 and SMBJ18A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the lazarev-lab/AEG_Active_Brake repository on GitHub, at the commit this page was made from: the board is Active_Brake_DC_motor.kicad_pcb and its schematic Active_Brake_DC_motor.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).